Post Buy Requirement
RA

Rotomech Automation Limited

Add Review

Our Products

  1. Testing Equipment

    2 Products available
  2. Surveillance Systems

    1 Products available
  3. Laboratory Apparatus

    1 Products available
  4. Electrical & Electronic Testing Devices

    1 Products available
  5. Surveillance Services

    1 Products available
  6. Industrial Heaters

    1 Products available
  7. Medical Accessories

    1 Products available
  8. Others Products 1 Products available

Our Products

Our Complete range of products are RD1000 Ground Penetrating Radar (GPR) and IAQ Analyzer.

Cable Pipe Locator

In an ever more regulated industry, the next generation of Radiodetection Cable Avoidance Tools, C.A.T4 and Genny4, build on over 30 years of Cable Avoidance expertise to enable operators to find more buried utilities, faster. These two innovative tools have been engineered to deliver a step change in capabilities with minimal change in work practices and training requirements. The C.A.T4 and Genny4 range is designed to assist in avoiding buried cables and pipes during excavation, reducing the risk of injury to personnel and damage to utilities. The C.A.T4 is designed to detect signals whether generated by the Genny4, inherently radiating from metallic services, or from the complimentary range of Sondes (Mice) and accessories designed to enable the location of non-conductive services. C.A.T4 and Genny4 is Radiodetections most advanced Cable Avoidance system to date, designed to deliver optimal performance, higher levels of safety, advanced features and at competitive cost of ownership
View Complete Details

Condition Monitoring

METZIN modern induction shrink-fit technology uses the expansion and contraction properties of metal to enable smaller shafts carry the same torsion moment. Proper shrink fitting prolong the roller bearings life by several times. Induction heating is also ideal for shrink-fit many other shaft mounted machine parts such as gears, pinions, seals and spacers that often require shrink fitting to avoid from suffer of reduced life expectancy due to improper installation. What constitutes "proper" fitting technique? Mechanical methods such as hammers and hydraulic presses risk damaging the inside surface of the inner ring and the bearing races. The better shrink fitting solution is via heating. But beware: blow torches and hot plates tend to overheat, while oil baths are slow heating, present environmental and safety hazards, cause bearing contamination and loss of prepublication.
View Complete Details

Condition Monitoring & Vibration Inst.

Solving difficult complex machinery problems require modern technologyinstrumentation experienced personnel & old fashioned commitment to meet the need of todays industries. Rotomech provide all three element, whenever our team of field engineersexecutives are deputed at our customer site for carrying out total condition monitoring field services provided on annual contract basis using software based single channeldual channel vibration spectrum analyzer our instruments are in compliance with ex ii 3g, ul, lloyds register & d n114 for use in hazardous location of all groups, class, zone & division making it intrinsically safe for use in class i, division 2, group a b c d t4 & class I zone 2 aex nc iic t4 and ex nc iic t4 and totally intrinsically safe to be used in petrochemcials, refinery, oil field etc.
View Complete Details

Geophysical & Structural Monitoring

The Freedom DATA instrument systems provides the user with unmatched flexibility for stress-wave based condition evaluation of concrete, masonry, asphalt, wood and other construction materials, as well as seismic testing of soil and rock and virtually any general testdata acquisition measurement. By changing instrument modules in the two built-in bays, the user can quickly switch between tests using any of the available NDE methods, while using similar software for data acquisition and analysis.
View Complete Details

Geovane Soil Shear Strength Tester

A 19mm vane blade is screwed in to the base of the Geovane and the vane is pushed into the soil. Simply rotate the Geovane at a rate of 1 revolution per minute and take a reading off the face when the soil fails. A pointer stays in place when failure occurs so all you have to do is look up the reading from the face on the supplied calibration chart to get your reading in kPa.
View Complete Details

Corrosion Monitoring

CORROSION MONITORING Division with a high technical skills base in corrosion, erosion and materials degradation processes and mechanisms. applies knowledge, skills and experience to provide solutions and systems that optimise the safety, integrity and life cost of clients' assets. Specialist cathodic protection (CP) services for the offshore industry, which includes the design, supply and installation of CP systems and monitoring.
View Complete Details

Intrinsically Safe Infrared Thermometer

It is a new generation of intelligent detecting instrument integrated with optical, mechanical and electronic technique. It is widely used to make non contact temperature measurement in the working environment where inflammable and explosive mixed gases exist. It has the functions of laser guide, backlight display, display keeping, low voltage alarm of the battery, easy to operate and continent to use.
View Complete Details

RD1000 Ground Penetrating Radar (GPR)

The RD1000 is an exciting and powerful addition to the utility surveyors toolkit. Using radar technology, the RD1000 displays an image map of underground features. With the RD1000, the technician can see a pipe or cable in its topographical context making it ideal for locating and excavating utilities. The advantage over a traditional, electromagnetic locator is that the RD1000 can see non-conductive materials including plastic pipes.
View Complete Details

METZIN Induction Heater

Induction heater design have utilized the eddy current induction principle like a transformers - its core and windings can be seen as the primary side, but the work piece acts as a short-circuited secondary winding, which heats up rapidly due to its great electrical resistance. This phenomenon allows the induction heater to control the heating by continuously monitoring the work piece temperature and adjusting its own heating power during the process. Hence results in even heating of only the inner bearing ring but the heater itself remains cool and safe to handle
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us