Reliable Storage System, Mumbai

Vasai, Mumbai, Maharashtra

Drive in Racks allow a lift truck to enter the rack from one side to pick up or pull out pallets. This is done because pallets can slide backwards on a continuous rail. Forklifts drive into the rack to access pallets two or more deep.

Drive- in rack can be configured to store loads three, four or more deep, creating extremely dense storage. A drive-in system, that stores pallets four high and five deep, for example, can hold 20 pallets storage bay, place a load in the desired position and the back out.

To allow lift trucks in to the bays, drive in systems are designed without traditional beams placed across the bays. Instead, pallets rest on rails that run along the insides of the bays, perpendicular to the aisles. Pallets in a drive-in racking system are stored on a First-in / Last-out basis (FILO). Each bay is typically dedicated to a single product, so drive-in rack is best used in warehouse storing large quantities of the same product.

USAGES

Drive - In racking is used where high-density storage is required. It is frequently used in facilities with a low number of product lines. Pallets are stored in a block system with two blocks generally served by one operating aisle. The trucks drive into the racking to load or retrieve pallets, which are stored on cantilevered rails running throughout the system. The first pallet in is the last one out unless a Drive-Through system is used whereby pallets can be loaded or retrieved from either side. Forklift trucks drive into lanes on racking specially built to provide support to the pallet along the pallet sides. Stacking often to 10 metres high and 4 or 5 but occasionally even 10 pallet positions deep. This system can provide a very dense storage capacity, often low in access and rotation of products. As the truck enters the racking, special precautions apply to ensure the compatibility of design between the truck, pallet, load and the racking. Flat floors are advantageous.Usually the rack design incorporates a stability structure at the rear of the rack and therefore drive in indicates single access from one side. Drive through requires this same stability to be provided by a variation in design.

his design is the same as drive-in rack. The difference is drive- through rack allows life trucks to enter the bays form either end. This considerably increases access to pallet loads, but requires an aisle on both ends of the racking system. Drive-through rack can be loaded from one end and emptied from the other, allowing first-in/first-out(FIFO).

	It is Cost effective.
	High density storage.
	Running into Depth.
	Can drive deep.
	Reduces the need for aisles.
	Drastically increases cubed space utilization.
	Loading & Retrieval from same side (LIFO).
	Loading from one side and retrieval from another side is also possible.
	Maxima space power Drive In storage system is recommended for large volumes storage requirements.

We offer long Span Racking System which is ideally used for storing bulky loads. These can be designed for single, multi tier or high rise applications. Its complete range of frames and beams fulfills a wide range of loading requirements, especially in tools room.

Some features of Long Span Non-Palletized Racking are:

	Most suitable for loads between 200-1500 kg.
	Easy to install and disassemble Available in different sizes
	Easy to install and disassemble Available in different sizes

Reliable pallet racking system representsthe best response for those warehouses in which it is necessary to store palletised products with a wide range of load types. The simplest of all Pallet Rack Storage Systems provides access to every pallet. Low cost equipment can be used offering simple adjustability and adaptability.

Pallet racking warehouse is generally laid out with single-entry wall racks on the perimeter sides and double-entry racks in the middle.

The working aisle measurement between each rack and the rack height depends upon the characteristics of the forklift trucks or lifting devices, pallet size and the height of the warehouse itself.

All cantilever uprights from can be used as single-sided or dual-sided designs and the rows of uprights can be any length required. The cantilever arms can be modified flexibly for stored goods with different heights and loading requirements. Subsequent adjustments and adaptations can be made without tools. In case you would like to store special materials or need to meet specific ambient conditions, our expert consultants will be happy to design customized concepts for you.

FEATURES
1.	All bolted arm connections
2.	Pre-punched connection hole
3.	Connection holes on side, not
corners of column
4.	Base is welded to column at
factory

the widest range of slotted angle shelvings custom built to suit your specific, needs supported by wide range of optional accessories like Cladding Sheets, Box Covers, Partition Plates, Panel guards, Punched Strips etc & load Carrying capacity ranging from 50 kgs to 600 kgs on each shelf.