Ratan Ancillaries

Naya Bazar, Ajmer, Rajasthan

CLEVELAND FLASH POINT & FIRE POINT APPARATUS

This apparatus is used for determination of flash point and fire point of petroleum products open cup flash above 80C as per specification IP 36 and IS: 1448 (P: 69) 1969. The apparatus consists of a cup, heating plate to specific dimension thermometer clip and test flame attachment with swivel joint for passing over test liquid surface in the prescribed manner, Heating is controlled by means of energy regulator fitted to the apparatus. Suitable for operation on 220 Volts 50 cycles AC Circuits.

RAP 132 - Cleveland flash point & fire point Apparatus Electrical Heating with Energy Regulator Gas Test Jet

RAP 133 - With OIL WICK Arrangement

RAP 134 - - Same as above with - Gas Jet & Oil Wick Arrangement COMBINED Model

• This apparatus is made as per IP 34, ASTMD-93 and IS 1448 (Part I) 1270 (P.21) and IS 1209-1953 method B. Used for finding out Flash Point above 70 C and below 300 C. The Instrument having Oil Test Jet/GasTest Jet Flame Device, stirrer with flexible shaft. The Assembly rests in Air Bath which is covered with Dome shape metal top. The cup is fitted with insulated Handle and locking arrangement near Cup flange. The assemble is kept on round shape electric heater with Seperate temp.regulator. Suitable for operation on 220 Volts 50 cycles AC Circuits
  RAP 125 - P. M. Flash Point App. Elect. Heated with Energy Regulator Oil Test Jet
  RAP 126 - -- Same as above -J Elect. Heated With Concealed Hot Plate & Oil Test Jet
  RAP 127 - P. M. Flash Point App. with Electronic Temp. Indicator and Regulator Oil Test Jet
  RAP 128 - P. M. Flash Point App. Elect. With energy Regulator, Geared Motor Stirrer (120 R.P.M.) Oil Test Jet
  RAP 129 - Pensky Martens Flash Point App. with Electronic voltage Variac and Digital Temp. Indicator and Constant Speed. Stirring device Oil Test Jet
  RAP 130 - Semi Automatic Flash Point Apparatus with Electronic Temp. Controller, Automatic Dipping cycle with Remote Control Oil Test Jet or Gas Test Jet.
  RAP 131 - Fully Automatic Flash Point App. Micro Controller based with LCD Display Temp. Range form 80C to 350 C 0.1c Direct Resolution. Automatic Stirrer Gas Test Jet System.
  
  Request Note :All above models can be supplied with \"Gas Test Jet\" system with Reducing Valve in place of Oil Jet Flame at extra cost.
  
  OPTIONAL ACCESSORIES:
  RAP 125 a - Openclip for Converting Close Model To Open Cup test Model as per IP 35
  RAP 125 b - IP 15C Low range (-7/110Cx05C) thermometer
  RAP 125 c - IP 16C High range (90x370Cx2C) thermometer
  RAP 125 d - Polish wooden case
  RAP 125 e - Spare Cup with Handle
  RAP 125 f - Spare Cover Assembly
  RAP 125 g - Spare Nichrome heating element

REDWOOD VISCOMETER MULTIPLE APPARATUS

It consists, One Red Wood No.1 cup and One Red Wood No. 2 cup are installed in the bath. The bath is made from S.S. Sheet The temperature is Controlled by Electonic Digital Temperature Controller. The Stirring is done by FHP electric motor in the heating compartment The unit has 2 sets of Oil Cup covers, thermometer Clips and ball valve.Suitable to operate on 220 volts AC Circuits.

RAP 109 :REDWOOD VISCOMETER MULTIPLE APPARATUS

TAR VISCOMETER APPARATUS As per IP 72 and is 1206 standards. It is used for determination the viscosity of road oils and cut back bitumen. It consists S.S. Bath with cup of 10 mm or 4mm orifice and sleeve, Stirrer with lifting clip and ball. The assembly kept on Suitable stand with leveling Screws. Suitable to operate on 220 Volts AC Mains.
RAP 110 - Electrical Heating with energy Regulator Control
RAP 110 A - Electrical Heating with Digital Indicator and Regulator
RAP 110 B - Electrical Heating with Voltage Varrier (Copper Coil)

TAR VISCOMETER MULTIPLE APPARATUS Consist 2 cups in a S.S. Water Bath mounted on Stand with levelling feet. Fitted with 1000 watts heater. Temperature is controlled by DIGITAL ELECTRONIC CONTROLLER with F.H.P. electric motor Stirrer. Supplied with one Tar Cup lOmm and one 4 mm orifice with Valves.
RAP 111 - Tar Viscometer Multiple Apparatus


Optional Accessories.
RAP 110 a - Spare Silver Plated Cup 10mm or 4mm orifice
RAP 110 b - Measuring Cylinder 100 ml cap.
RAP 110 c - IP8C (0/45CX0.2C) Low Range Thermometer
RAP 110 d - IP9C (40x85Cx.2C) Medium Range Thermometer
RAP 110 e - IPI OC (76x122Cx0.2C) High Range Thermometer
RAP 110 f - Polish Wooden case RAP 110 g Spare Heater 400 W
RAP 110 h - Electronic Stop Watch

SAYBOLT VISCOMETER APPARATUS

Made as per ASTMD-88 specifications with Universal and Furol Jets made of Stainless Steel. Stirring is done by hand with turn table arrangement (without Strainer, withdraw) Tube and glass wares).
Suitable to operate on 220 Volts AC mains.

RAP 113 - Elect. Heating with Energy Regulator control

RAP 113 A - Elect. Heating with Electronic Indicator and Regulator

RAP 114 - Single Tube Saybolt Viscometer with Control Pannel (Double Walled) Digital Electronic Temp. Controller and F.H.P. Motor Stirrer

RAP 114 A - ----Same as above---- with Two Tubes Set

OPTIONAL ACCESSORIES

RAP 113 a - Strainer for filtering oil

RAP 113 b - Withdrawl Tube (Metal)

RAP 113 c - Spare Cup without Jets

RAP 113 d - Spare Jet Universal

RAP 113 e - Spare Jet Furol

RAP 113 f - Flask 60 cc.

RAP 113 g - Polish Wooden Case for above App.

RAP 113 h - ASTM 17C Range 19 to 27C 0 Thermometer

RAP 113 i - ASTM 18C Range 34 to 42C Thermometer

RAP 113 j - ASTM 19C Range 49 to 57C Thermometer

RAP 113 k - ASTM 20C Range 57 to 65C Thermometer

RAP 113 l - ASTM 21 C Range 79 to 87C Thermometer

RAP 113 m - ASTM 22C Range 95 to 103C Thermometer

RAP 113 n - COMMON RANGE Thermometer 0-100C

ENGLER VISCOMETER APPARATUS

As per IP 212 and ASTMD-490. Used for determining the Viscosity of lubricating and fuel oils.

RAP 112 - Electrical Heating with energy regulator control

RAP 112 A - Electrical Heating with Electronic Indicator and Regulator

OPTIONAL ACCESSORIES

RAP 112 a - Engler ASTM 24C Thermometer (39/54Cx0.2C)

RAP 112 b - Engler ASTM 25C Thermometer l(95/105Cx0.2C)

RAP 112 c - Teflon Valve

RAP 112 d - Spare Wooden Valve

RAP 112 e - flask 200 ml. capacity

RAP 112 f - Wooden case for above Apparatus

RAP 112 g - Spare Heater for above

DISTILLATION APPARATUS
[As per IP 123, 191 and IS 1448 P : 18 specifications]

This apparatus is used for determinations of distillation characteristics of petroleum products . The instrument consists of metal shield to support distillation flask with GEARED HEIGHT ADJUSTABLE DEVICE. It has a slot for vapour tube. A glass window is provided in front side for clear view of inside objects. It also has cooling bath or condenser with M.S. black painted stand. Electrically heated. The instrument is supplied with two square asbestos board with 50 mm and 70 mm holes. (without glass wares)

RAP 140 - Single Distillation Apparatus electrically heated with energy Regulator with Gear device

RAP 141 - Single Distillation Apparatus with Energy Regulator and Digital Temp. Indicator with Gear device

RAP 142 - Twin (Duplex) Distillation Apparatus elect. Heated model with two energy Regulators with Gear device

RAP 143 - Twin (Duplex) Distillation Apparatus with Electonic Regulator and Digital Temp. Indicator with Gear Device

RAP 144 -Distillation Apparatus for Crude Petrloeum as per IP-24 with One glass Condensor Elect., with Energy regulator control CESSORIES.


OPTIONAL ACCESSORIES

RAP 140 a - Distillation Flask 125ml

RAP 140 b - Distillation Flask 250ml

RAP 140 c - Measuring Receiver 100 ml

RAP 140 d - spare Asbestos Board 38mm or 50 mm or 70 mm Dia Hole.

RAP 140 e -Thermometer IP 5C (-2/3000Cx1C)

RAP 140 f - Thermometer IP 6C (-2/4000Cx1C)

It is made as per IP 13, ASTM D- 189 Specifications . It is useful to determine amount of Carbon Residue when an oil is evaporated under Specified Conditions. The apparatus consists of spun sheet iron crucible 25 c c Capacity, Sheet Iron hood and sheet iron block on a stand, gas Burnor.

RAP 150 A - Conradson Carbon Residue single Test Apparatus (Gas Burner)

RAP 150 B - Elect. Heating With Energy Regulator Control

RAP 151 A - Conradson Carbon Residue Four Test App. (Gas Burner)

RAP 151 B - -same as above- but Elect Heating with Separate Energy Regulator Controls

This is made according to specification laid by IP 15 & IS 1448 (P : 10) 1970. The pour point is lowest temperature at which the oil will just fail to flow. The apparatus Consists main cooling bath made out of S.S. sheet and stand unit with drain plug and cover has provision for fitting thermometer and a filling aperture for adding freezing mixture. A Glass jar for containing oils, Jacket, disc and gasket as specified are also provided.

RAP 152 - Cloud & Pour Point Single Test with Insulated Body

RAP 153 - Cloud & Pour Point Two Test with Insulated Body

RAP 154 - Cloud & Pour Point Four Test with Insulated Body

RAP 155 - Cloud & Pour Point Six Test with Insulated Body

RAP 156 - Cloud & Pour Point App. WITH REFRIGERATION SYSTEM (for 2 test App.) Temp. upto - 30C.

optional accessories
RAP 152 a - Cloud & Pour Point Thermometer IP IC

RAP 152 b - Cloud & Pour Point Thermometer IP 2C

RAP 152 c - Spare Glass Jar with cork

RAP 152 d - Spare Metal Jacket with Disc.

RAP 152 e - Polish wooden case for - Single Test, Four Test, Six Test

RAP 152 f - Rexine Dust Cover for refrigeration Unit

REID VAPOUR PRESSURE TEST APPARATUS

Made as per IP 69 & IS 1448 (P: 39). 1967 elect. Heated with FHP motor Stirrer temp. controlled by Electronic Digital Temp. Controller. The apparatus consists one air chamber, one Liquid Chamber without cock and pressure gauge.

RAP 157 - Single Test Bath

RAP 158 - Double Test Bath


OPTIONAL ACCESSORIES

RAP 157 a - Liquid Chamber with Cock (if Required)

RAP 157 b - Spare Airchamber only RAP 157 c NP Pressure Gauge 0-1 Kg. / Cm2

copper strip corrosion test apparatus

double walled stainless steel chamber bath outer chamber made of mild steel sheet attractive painted. As per ip 154 and is 1448 (p - 15) to accomodate . Temperature is controlled by electronic digital controller (without s.s. Bomb)

rap 159 - water bath

rap 160 - water bath

optional accessories

rap 159 a - stainless steel bomb

rap 159 b - vice single strip

rap 159 c - vice four strip

rap 159 d - copper strip (pack of 3)

rap 159 e - test tube

[ As per IP 49, 50 & 167 specifications and also per IS 1448 (P: 60) & (P: 93)]

This apparatus is used for penetration test on a wide variety of materials. It consists of a head Support mounted on a vertical rod which can be adjusted for height. A rack and pinion and pointer assembly provides fine adjustment of needle tip to Sample and in Corporates a Slipping clutch mechanism which make reading of penetration and subsequent resetting a sample and accurate operation. The dial graduate from 0-400 in one tenth millimeter Sub Division. The Instrument is supplied with two sample containers & 2 Wts.

RAP 137 - Penetrometer with containers and weights having peneteration Needle. (Bitumen)

RAP 138 A - Penetrometer Apparatus with containers and weights having peneteration CONE HOLLOW type (Grease)

RAP 138 B - -Same as above - but with Geared arrangement for moving the arm with geared unit

RAP 139 A - Penetrometer with Brass Cone & Needle With DIGITAL TIMMER DEVICE (Adjustable)

RAP 139 B - --- Same as above --- but with Geared arrangement for moving the arm with geared unit

OPTIONAL ACCESSORIES:
RAP 137 a - Spare penetration Needle (Pack of Two)

RAP 137 b - Spare penetration solid cone

RAP 137 c - Spare penetration Brass hollow cone

RAP 137 d - Grease worker hand operated

RAP 137 e - Grease worker hand operated Big Handle (Lever Type)

RAP 137 f - Grease cutter as per IP 50

RAP 137 g - Transfer Dish

SOFTENING POINT APPARATUS
(Ring & Ball Apparatus)

For determination of softening point of bituminious materials according to IP 58 and IS 1205-1958. Softening point is that temperature at which the speciman under test becomes soft enough to allow a steel ball of specific dimensions to fall a required distance under test condition. The apparatus consists of glass beaker, ring Stand, two steel balls with rings and ball guides, hand Stirrer.

RAP 161 - Softening Point Apparatus (without Glass Beaker)

RAP 162 - Softenting Point Apparatus with glass Beaker

RAP 163 A - Softening Point Apparatus with F.H.P. elect.motor driven Stirrer and electric heater with Energy. Regulator Control.

RAP 163 B - ---Same as Above--- with DIGITAL TEMP. CONTROLLER UNIT

OPTIONAL ACCESSORIES.

RAP 161 a - Thermometer IP 60C

RAP 161 b - Thermometer IP 61 C

RAP 161 c - Spare Ring with Ball-Centring Guide and Steel Ball (pack of 2)

SMOKE POINT APPARATUS

RAP 172 - Smoke Point Apparatus as per IP 57 & IS 1448 (P-31) & ASTM D 1322

RAP 172 a - Spare Candle

RAP 172 b - Spare Wick

MELTING POINT APPARATUS

This apparatus consists of a cylindrical block of Aluminium with a built in electrical heating element.The mounted Alum. block illuminates from below by a lamp fixed in its housing. The aluminium block accept three capillary tubes and mercury thermometer.The temperature is controlled by rotary switch. The magnifying lense provided for viewing objects clear. Suitable for operation on 220 Volts AC circuits

RAP 166 - Melting Point Apparatus

RAP 167 - Melting Point App. Digital Temp. Indicator with Cooling Plug

RAP 166 a - IP 63C Thermometer