Q- Log Controls And Systems

Bhumkar Nagar, Pune, Maharashtra

Features DIN rail mountableEightFour phototriacs on a single boardLED indication for input signalPositive supply commonnegative supply common selection by jumpers for ip signalOutput points in onetwo groups. Each group consists four op pointsIndividual op point can be grouped ungrouped by jumper selection Technical Specifications Input signal voltage:20 VDC-28VDC28VDC4-9 VDC 10-15 vdcMax. input current:20 mA @24VDCMax. output voltage:600 VACMin.output voltage:24 VACMax. load (rms) per output point:1 AmpPeak non repeatitive surge current:10 AmpInput to output electrical isolation: 3.55 KVMax. Voltage drop in output voltage: 1.7 V @ 1 Amp loadSwitching delay Off to ON and ON to OFF:Less than half cycleLoad type:Resistive and Inductive Size:8 point :-118x90x50 (WXHXD)4 point :-62x90x50 (WXHXD) Applicationsa) For switching contactors from PLC outputs.b) For switching AC loads like single phase motors, AC actuators, AC solenoid valves, AC electromagnets in industrial use directly from controller outputs.c) To switch Air conditioner, microwave ovens, washing machines, personal hygiene systems, refrigerators, fan heaters, domestic fans, inductive heating cookers, water heaters directly from controller outputs.d) In all applications where we need very fast switching and require isolation between driver and driven circuits. The load can be inductive or resistive.Available in 48 points variants.Solid State Relay boards with input signal other than 24VDC can be supplied on demand. StandardsApprovals CE certifiedPCB:IEC 61373Optotriac:ULVDEConnectors:CEProfile and end plates:UL Caution: DO NOT USE SSR BOARD FOR SWITCHING DC SUPPLY !

Features DIN rail mountable, compact and easy for troubleshooting.TwoFourEight phototransistors on a single board.Sink or Source type input connectableLED indication for input signal.Ideal to drive hydraulic and pneumatic solenoid coils.Built in free wheeling diode across driving load for every individual output point Technical Specifications Input signal voltage:3 VDC-100 VDC, Typical voltage is 24105VDCMax. input current:20 mA @24VDCMax. output voltage:60 VDCMin.output voltage:Supply voltage-4 VDCMax. load per output point:5 AmpsPeak non repeatitive surge current:8 AmpsInput to output electrical isolation: 3.55 KVMax. Voltage drop in output voltage: 2.5 V @ 2 Amp loadSwitching ONOFF delay:10 microsecondsLoad type:Resistive and InductiveSize:40X90 (2 POINTS), 70x90 (4 points), 90x140 (8 points) Applicationsa) For switching contactors from PLC outputs.b) For switching DC loads like solenoid valves, DC actuators, DC Lamps, DC electromagnets in industrial use directly from controller outputs.c) In all applications where we need very fast switching and require isolation between driver and driven circuits. The load can be inductive or resistive.Available in 248 points variants.Solid State Relay boards with input signal other than 24105 VDC can be supplied on demand.Caution: DO NOT USE SSR BOARD FOR SWITCHING AC SUPPLY ! StandardsApprovals CE certifiedPCB:IEC 61373Optoisolatortransistor:ULVDEConnectors:CEProfile and end plates:UL CONNECTION DETAILS ON NEXT PAGE !

Application Relay Interface Module 1 changeover ACDC used to interface 24VACDC digital outputs to contactorssoleoid valvesindications etc.Load and PLC ops or transformer secondary are galvanically isolated COMPONENT SPECIFICATIONS Relay:24VDC coil, 1 changeover OmronRelay socket:1changeover PCB soldering typeTerminals:screw type suitable for 2.5 sq. mm wires TECHNICAL SPECIFICATIONS Input data: Operating voltage: 24 VAC24 VDC +- 10%Input current: Max 20mA@24 VDCACProtection across relay coil: Free wheeling diodeIndication: 3mm LEDSinkSource: Selectable by jumpersNo of relays: 2 or 4 or 8Terminals: Screw type suitable for 2.5 sq. mm wiresConductor size: 025-2.5 sq. mmInsulation stripping length: 7 mm Output Data: Contact type: SPDT (1 changeover NO-Pole-NC)Max. current: 10Amps@250 VAC or 30 VDCFuse protection :available on request Output wiring :Potential freeTerminals : screw type suitable for 2.5 sq. mm wiresConductor size :025-2.5 sq. mmInsulation stripping length :7 mmModule dimensions (HXLXD) : 90x36x70 (2 Relay board) 90x68x70 (4 Relay bo ard) 90x130x70 (8 Relay board)

Application Relay Interface Module 1 changeover DC used to interface 24DC digital outputs to contactorssolenoid valvesindications etc.Load and PLC ops secondary are galvanically isolated. COMPONENT SPECIFICATIONS Relay: 24VDC coil, 2 changeover OmronRelay socket: 1 changeover PCB soldering typeTerminals: Screw type suitable for 2.5 sq. mm wiresProfile and end plates:Phoenix make TECHNICAL SPECIFICATIONS Input data: Operating voltage: 24 VDC +- 10%Input current: Max 20mA@24 VDCACProtection across relay coil: Free wheeling diodeIndication: 3mm LEDSinkSource: selectable by jumpersNo of relays: 2 or 4 or 8Terminals: screw type suitable for 2.5 sq. mm wiresConductor size: 025-2.5 sq. mmInsulation stripping length: 7 mm Output Data: Contact type: SPDT (1 changeover NO-Pole-NC)Max. current: 10Amps@250 VAC or 30 VDCFuse protection: Available on requestOutput wiring: Potential freeTerminals: Screw type suitable for 2.5 sq. mm wiresConductor size: 025-2.5 sq. mmInsulation stripping length: 7 mmModule dimensions (HXLXD): 90x36x70 (2 Relay board) 90x68x70 (4 Relay bo ard) 90x130x70 (8 Relay board)

Features DIN rail mountableEightFour DC SSRs on a single boardSink or Source input selection by jumper selectionLED indication for input signalSemiconductor Fuse protection for short circuit and overcurrent.Output points in two groups. Each group consists four op points. Technical Specifications Input signal voltage:20 VDC-28VDC, Typical voltage is 24VDCMax. input current:20 mA @24VDCMax. output voltage:100 VDCMin.output voltage:5 VDCMax. load per output point:5 AmpPeak non repeatitive surge current:8 AmpInput to output electrical isolation: 3.55 KVMax. Voltage drop in output voltage: 2.5 V @ 2 Amp loadSwitching ON delay:7 microsecondsSwitching OFF delay:10 microsecondsLoad type:Resistive and Inductive Applicationsa) For switching contactors from PLC outputs.b) For switching DC loads like solenoid valves, DC actuators, Lamps, DC electromagnets in industrial use directly from controller outputs.c) In all applications where we need very fast switching and require isolation between driver and driven circuits. The load can be inductive or resistive.Available in 8 points and 4 points variants. Solid State Relay boards with input signal other than 24VDC can be supplied on demand. Caution: DO NOT USE SSR BOARD FOR SWITCHING AC SUPPLY ! StandardsApprovalsCE certifiedPCB:IEC 61373OptoisolatorTransistor:ULVDEConnectors:CEProfile and end plates:UL

Application Relay Interface Module 1 changeover DC used to interface 24DC digital outputs to contactorssolenoid valvesindications etc. Load and PLC ops secondary are galvanically isolated. COMPONENT SPECIFICATIONS Relay: 24VDC coil, 1 changeover OmronRelay socket: 1 changeover PCB soldering typeTerminals: Screw type suitable for 2.5 sq. mm wiresProfile and end plates: Phoenix make TECHNICAL SPECIFICATIONS Input data: Operating voltage: 24 VDC +- 10%Input current: Max 20mA@24 VDCACProtection across relay coil: Free wheeling diodeIndication: 3mm LEDNo of relays: 2 or 4 or 8Terminals: Screw type suitable for 2.5 sq. mm wiresConductor size: 025-2.5 sq. mmInsulation stripping length: 7 mm Output Data: Contact type: SPDT (1 changeover NO-Pole-NC)Max. current: 10Amps@250 VAC or 30 VDCFuse protection: Available on requestOutput wiring: Potential freeTerminals: Screw type suitable for 2.5 sq. mm wiresConductor size: 025-2.5 sq. mmInsulation stripping length: 7 mmModule dimensions (HXLXD): 90x36x70 (2 Relay board) 90x68x70 (4 Relay board) 90x130x70 (8 Relay board)

Application Relay Interface Module 1 changeover DC used to interface 24DC digital outputs to contactorssolenoid valvesindications etc. Load and PLC ops secondary are galvanically isolated. Fast acting fuse is at NO point for short circuit protection. COMPONENT SPECIFICATIONS Relay: 24VDC coil, 1 changeover OmronRelay socket: 1 changeover PCB soldering typeTerminals: Screw type suitable for 2.5 sq. mm wiresProfile and end plates: Phoenix make TECHNICAL SPECIFICATIONS Input data: Operating voltage: 24 VDC +- 10%Input current: Max 20mA@24 VDCACProtection across relay coil: Free wheeling diodeIndication: 3mm LEDNo of relays: 2 or 4 or 8Terminals: Double decker screw type suitable for 2.5 sq. mm wiresConductor size: 025-2.5 sq. mmInsulation stripping length: 7 mm Output Data: Contact type: SPDT (1 changeover NO-Pole-NC)Max. current: 10Amps@250 VAC or 30 VDCFuse protection: AvailableOutput wiring: Potential freeTerminals: Screw type suitable for 2.5 sq. mm wiresConductor size: 025-2.5 sq. mmInsulation stripping length: 7 mmModule dimensions (HXLXD): 130x38x70 (2 Relay board) 130x70x70 (4 Relay board) 130x134x70 (8 Relay board)

Features DIN rail mountableEightFour DC SSRs on a single boardSink or Source input selection by jumper selectionLED indication for input signalSemiconductor Fuse protection for short circuit and overcurrentOutput points in two groups. Each group consists four op points Technical Specifications Input signal voltage:20 VDC-28VDC, Typical voltage is 24VDCMax. input current:20 mA @24VDCMax. output voltage:100 VDCMin.output voltage:5 VDCMax. load per output point:5 AmpPeak non repeatitive surge current:8 AmpInput to output electrical isolation: 3.55 KVMax. Voltage drop in output voltage: 2.5 V @ 2 Amp loadSwitching ON delay:7 microsecondsSwitching OFF delay:10 microsecondsLoad type:Resistive and Inductive Applicationsa) For switching contactors from PLC outputs.b) For switching DC loads like solenoid valves, DC actuators, Lamps, DC electromagnets in industrial use directly from controller outputs.c) In all applications where we need very fast switching and require isolation between driver and driven circuits. The load can be inductive or resistive.Available in 8 points and 4 points variants.Solid State Relay boards with input signal other than 24VDC can be supplied on demand. Caution: DO NOT USE SSR BOARD FOR SWITCHING AC SUPPLY ! StandardsApprovals CE certifiedPCB:IEC 61373OptoisolatorTransistor:ULVDEConnectors:CEProfile and end plates:UL