Clients can avail from us Ultimate Waterproof Coating which is a thermal insulating, an elastomeric, resilient and waterproof coating. ULTIMATE is a single component, water based high solids, elastomeric acrylic resin based coating. Ultimate Waterproof Coating is an advanced acrylic technology product manufactured by combination of pigments, reinforcing fillers and an Australian thermal non-conductive material. On application, Ultimate Waterproof Coatings form a waterproof elastomeric seal in the form of monolithic uniform membrane, which provides protection from ageing, ultraviolet rays and normal weathering. It reflects heat as well as it does not allow the heat flux transmission. Ultimate Waterproof Coating reduces building maintenance cost as well as saves air conditioning energy up to 25 %. Its performance is more effective than that of the conventional waterproofing and protective products available in the market.

Benefits

• Single component, easily applicable by brush, roller or spray.
• Adheres strongly to a wide variety of sound substrates such as concrete, metal, modified bitumen wood, polyurethane foam etc.
• Water vapor transmission decreases maintenance cost.
• Water seal increases longevity.
• Ultraviolet light protection maintains aesthetic appearance.
• Heat - non - conductive property saves air conditioning energy cost up to 25%.
• Unique non-conductivity (to heat) properly keeps the building warm in cold season and cool in hot season.
• Prevents growth of moss, fungus and algae.
• Repels airborne pollutants and dirt that makes the substrate look new for years after application.
• Lightweight-puts less stress on the building.
• Nontoxic-safe for the environment and the people, applying it.
• High reflective-light reflection value of 92 at 700nm.
• Attractive color shades available, if required.

Grades

• Ultimate HL : zontal surface. Has extra elastomeric resilient property to meet the coefficients of expansion and contraction, wear tear erosion & abrasion resistant.
• Ultimate VL : ertical surface. Has elastomeric membrane property to meet the movement.

End Uses Building roof, terraces and exterior walls, industrial - factory roofing - concrete, asbestos, tin etc. Cold storages, Electronic exchange building roofs, hospital buildings, etc. Direction For Use Surface Cleaning Surface preparation is very important to get the best result and to avoid failure. The substrate must be sound enough, clean and free of dirt, grease, oil, sludge, moss, blistered cement coating, loose plaster etc. Thoroughly wire brush the surface to remove saturated dirt and lose particles. Wash the surface to remove dust. Allow the surface to dry completely. Sealer / Primer Coat The concrete or cementitious substrates are highly porous. It is necessary to make the substrate less Absorptive so that the top coats film thickness remains same. Krishna SEALER is highly elastomeric acrylic emulsion polymer without filled system has extra ordinary penetrating power which seals the porosity. Micro crevices of the substrate. It provides strong adhesion to the substrate and top coating. Due to non-filled system it overcomes the problem of linear stress and strain created in the substrate. Apply one coat of SEALER as a primer coat by brush. Apply the top coat after one hour but within four hours of drying of SEALER coat. Application Seal the cracks of parapet wall and roof substrate by creating a groove of 3mm size, with acrylic sealant. Allow the sealant to dry for 24 hours before applying a sealer / primer. Mixing Mix the content of pack in its original container by stirring with the help of a wooden stick to a uniform, homogenous free flowing paste consistency. Apply the first coat of Ultimate by brush or roller generously. Allow the coating to dry for attest 3 hours before applying second coat. Minimum two coats are recommended. If required, additional coat may be applied. Allow the coating to dry / cure on its own, external curing is not required. Cleaning : Tools and equipment to be cleaned with water immediately after the use. Storage & Shelf Life : Store the material in cool dry place. Shelf life of the unopened container is one year from the date of manufacture. Packing : 1, 4, 20 Liter packs Precaution

• Do not apply on wet or damp substrate.
• Do not apply in rain.
• Do not dilute more than 20% with water.

Clients can avail from us Ultimate Waterproof Coating which is a thermal insulating, an elastomeric, resilient and waterproof coating. ULTIMATE is a single component, water based high solids, elastomeric acrylic resin based coating. Ultimate Waterproof Coating is an advanced acrylic technology product manufactured by combination of pigments, reinforcing fillers and an Australian thermal non-conductive material. On application, Ultimate Waterproof Coatings form a waterproof elastomeric seal in the form of monolithic uniform membrane, which provides protection from ageing, ultraviolet rays and normal weathering. It reflects heat as well as it does not allow the heat flux transmission. Ultimate Waterproof Coating reduces building maintenance cost as well as saves air conditioning energy up to 25 %. Its performance is more effective than that of the conventional waterproofing and protective products available in the market.

Benefits

• Single component, easily applicable by brush, roller or spray.
• Adheres strongly to a wide variety of sound substrates such as concrete, metal, modified bitumen wood, polyurethane foam etc.
• Water vapor transmission decreases maintenance cost.
• Water seal increases longevity.
• Ultraviolet light protection maintains aesthetic appearance.
• Heat - non - conductive property saves air conditioning energy cost up to 25%.
• Unique non-conductivity (to heat) properly keeps the building warm in cold season and cool in hot season.
• Prevents growth of moss, fungus and algae.
• Repels airborne pollutants and dirt that makes the substrate look new for years after application.
• Lightweight-puts less stress on the building.
• Nontoxic-safe for the environment and the people, applying it.
• High reflective-light reflection value of 92 at 700nm.
• Attractive color shades available, if required.

Grades

• Ultimate HL : zontal surface. Has extra elastomeric resilient property to meet the coefficients of expansion and contraction, wear tear erosion & abrasion resistant.
• Ultimate VL : ertical surface. Has elastomeric membrane property to meet the movement.

End Uses Building roof, terraces and exterior walls, industrial - factory roofing - concrete, asbestos, tin etc. Cold storages, Electronic exchange building roofs, hospital buildings, etc. Direction For Use Surface Cleaning Surface preparation is very important to get the best result and to avoid failure. The substrate must be sound enough, clean and free of dirt, grease, oil, sludge, moss, blistered cement coating, loose plaster etc. Thoroughly wire brush the surface to remove saturated dirt and lose particles. Wash the surface to remove dust. Allow the surface to dry completely. Sealer / Primer Coat The concrete or cementitious substrates are highly porous. It is necessary to make the substrate less Absorptive so that the top coats film thickness remains same. Krishna SEALER is highly elastomeric acrylic emulsion polymer without filled system has extra ordinary penetrating power which seals the porosity. Micro crevices of the substrate. It provides strong adhesion to the substrate and top coating. Due to non-filled system it overcomes the problem of linear stress and strain created in the substrate. Apply one coat of SEALER as a primer coat by brush. Apply the top coat after one hour but within four hours of drying of SEALER coat. Application Seal the cracks of parapet wall and roof substrate by creating a groove of 3mm size, with acrylic sealant. Allow the sealant to dry for 24 hours before applying a sealer / primer. Mixing Mix the content of pack in its original container by stirring with the help of a wooden stick to a uniform, homogenous free flowing paste consistency. Apply the first coat of Ultimate by brush or roller generously. Allow the coating to dry for attest 3 hours before applying second coat. Minimum two coats are recommended. If required, additional coat may be applied. Allow the coating to dry / cure on its own, external curing is not required. Cleaning : Tools and equipment to be cleaned with water immediately after the use. Storage & Shelf Life : Store the material in cool dry place. Shelf life of the unopened container is one year from the date of manufacture. Packing : 1, 4, 20 Liter packs Precaution

• Do not apply on wet or damp substrate.
• Do not apply in rain.
• Do not dilute more than 20% with water.