We designed and manufactured a Twin Station, 8 Axes, CNC Controlled, Stock Turning SPM for a large scale component manufacturing industry in Bangalore. This SPM is designed to take the load off 8 high end turnin

Problems faced by the customer:

• The cast job of the customer has a stock removal of around 8 mm in the bore and face.
• The customer cannot reduce the stock during casting stage, as the job profile is such that any reduction in stock at one point would eat up into the finished area at another point, leaving no option, but to retain huge, machining stock on all the walls of the components.
• On a CNC turning center, the cycle time required is 10 minutes for rough turning of 7 mm stock and the rest 1 mm would be finish-turned in a cycle time of 2 minutes. Total cycle time is about 12 minutes.
• It is noted that the turning centers is not suitable for heavy cuts beyond 3 mm which was leading to the increase in the cycle time.
• Customer approached us to manufacture a CNC turning SPM, which could cut 7-8 mm in one single go.

g centers.

• A twin station concept – one station to bore and face the front end of the job, the other to bore and face the rear end of the job.
• Each station has 2 sets of compound slides with servo driven cross and longitudinal axes. One set of compound slide does facing while the other will be used to bore.
• Both the facing and boring slides will work simultaneously to reduce the cycle time.
• Slides made of male, heavy duty, extra rigid, case hardened guideway strips and female turcite lining.
• Many innovative design features for reducing the cost, without diluting the stock removal capabilities within the specified time.

• Manually load cast job onto left hand chuck & on the auto-cycle button.
• Job gets clamped automatically & head stock starts rotating
• Machining of the face & ID of the front end of the job takes place.
• While machining on LH station is going on, operator loads an ID machined job on RH station.
• On the auto-cycle button & rear side machining of the job takes place in the RH station.

Every 75 seconds, one rough turned component is achieved.

• The customer is now getting a rough turned component at the rate of 1 piece/75 seconds, compared to the earlier 1 piece/10 minutes. i.e. a cycle time reduction of 87.5%
• A comparatively less accurate, highly affordable, Stock Turning CNC SPM is expected to result in elimination of 8 high end, accurate, expensive CNC turning centers, which are hitherto used for rough turning operations.
• Reduction in man power – 8 CNC operators along with 8 turning centers are now available for more gainful work.
• Increased output.
• After rough turning in our machine, finish turning is carried out on CNC tuning centers, thereby cutting down the whole cycle time from 1 piece/12 minutes to 1 piece/3.25 minutes. i.e. a cycle time reduction of around 73%.

We designed and manufactured a Twin Station, 8 Axes, CNC Controlled, Stock Turning SPM for a large scale component manufacturing industry in Bangalore. This SPM is designed to take the load off 8 high end turnin

Problems faced by the customer:

• The cast job of the customer has a stock removal of around 8 mm in the bore and face.
• The customer cannot reduce the stock during casting stage, as the job profile is such that any reduction in stock at one point would eat up into the finished area at another point, leaving no option, but to retain huge, machining stock on all the walls of the components.
• On a CNC turning center, the cycle time required is 10 minutes for rough turning of 7 mm stock and the rest 1 mm would be finish-turned in a cycle time of 2 minutes. Total cycle time is about 12 minutes.
• It is noted that the turning centers is not suitable for heavy cuts beyond 3 mm which was leading to the increase in the cycle time.
• Customer approached us to manufacture a CNC turning SPM, which could cut 7-8 mm in one single go.

g centers.

• A twin station concept – one station to bore and face the front end of the job, the other to bore and face the rear end of the job.
• Each station has 2 sets of compound slides with servo driven cross and longitudinal axes. One set of compound slide does facing while the other will be used to bore.
• Both the facing and boring slides will work simultaneously to reduce the cycle time.
• Slides made of male, heavy duty, extra rigid, case hardened guideway strips and female turcite lining.
• Many innovative design features for reducing the cost, without diluting the stock removal capabilities within the specified time.

• Manually load cast job onto left hand chuck & on the auto-cycle button.
• Job gets clamped automatically & head stock starts rotating
• Machining of the face & ID of the front end of the job takes place.
• While machining on LH station is going on, operator loads an ID machined job on RH station.
• On the auto-cycle button & rear side machining of the job takes place in the RH station.

Every 75 seconds, one rough turned component is achieved.

• The customer is now getting a rough turned component at the rate of 1 piece/75 seconds, compared to the earlier 1 piece/10 minutes. i.e. a cycle time reduction of 87.5%
• A comparatively less accurate, highly affordable, Stock Turning CNC SPM is expected to result in elimination of 8 high end, accurate, expensive CNC turning centers, which are hitherto used for rough turning operations.
• Reduction in man power – 8 CNC operators along with 8 turning centers are now available for more gainful work.
• Increased output.
• After rough turning in our machine, finish turning is carried out on CNC tuning centers, thereby cutting down the whole cycle time from 1 piece/12 minutes to 1 piece/3.25 minutes. i.e. a cycle time reduction of around 73%.