The modular workstation for any number of persons with work surface of any size with half  height

partition should comprise of:

a) for 70 mm (of height 4' and thickness and minimum overall thickness of 70 

mm) made of : 

i) Structural members fabricated of 1.50 mm to 2.20 mm pure 100%  aluminium 

extrusion channel with epoxy / powder coating  min. of 40 to 50 micron. 

ii) Two sides of partition panels finished partially with 9 mm thick prelaminated particle 

board and in between space of 52 mm out of over all thickness of 70 mm to be kept 

vacant for universal data and cable management system. Partial panel may be  with 

glass panel of minimum thickness 5mm. for some areas for better visibility and 

lighting. 

iii) Box type raceways open able on both sides at bottom level and as required below or 

above table height for carrying electrical and data cables. Skirting covers of height 

120 – 130 mm with materials fabricated with prelaminated particle board of 

thickness 9mm. 

iv) Slots in vertical sides for horizontal wire management of cables. 

v) General: Trims finish –Aluminium epoxy coated with 40-50 micron. All metal 

sections,  cantilever brackets to hold the work tables and tops and aluminium profile 

finished in epoxy coating of thickness 45 to 50 micron of approved shade.

for 30 mm-  The entire structural frame viz. horizontals and verticals are made of 30mm 

thick high quality aluminum extruded interlocking sections. Semi-circular top and 

vertical trims are made of aluminum extrusions which are snap fit. Provision of dual 

management facility is available. As per the international standards corner caps and 

top caps are made of Zinc moulds. Levelers are provided to overcome unevenness 

in the flooring. Snap fit tiles compromises of 15 mm prelam board on both making 30 

mm thick over all, Magnetic Fabric board. 30mm snap fit panel fixtures are made of 

zinc moulds. The top, vertical and corner trims are available in standard powder 

coating finish of international standards.  ( Decor-x make )

for 60 mm-  The entire structural frame viz. horizontals and verticals are made of 60mm 

thick high quality aluminum extruded interlocking sections. Semi-circular top and 

vertical trims are made of aluminum extrusions which are snap fit. Provision of dual 

management facility is available. As per the international standards corner caps and 

top caps are made of Zinc moulds. Levelers are provided to overcome unevenness 

in the flooring. 60mm snap fit panel fixtures are made of zinc moulds. The top, 

vertical and corner trims are available in standard powder coating finish of 

international standards.  ( Decor-x make )

for 50 mm- The entire structural frame viz. horizontals and verticals are made of 50mm 

thick high quality aluminum extruded interlocking sections. Semi-circular top and 

vertical trims are made of aluminum extrusions which are snap fit. Provision of dual 

management facility is available. As per the international standards corner caps and 

top caps are made of Zinc moulds. Levelers are provided to overcome unevenness 

in the flooring. Snap fit tiles compromises of 4 mm prelam board on both side 

making 48 mm thick over all, Magnetic Fabric board . 50mm snap fit panel fixtures 

are made of zinc moulds. The top, vertical and corner trims are available in standard 

powder coating ( moon shell grey ) finish of international standards.

The modular workstation for any number of persons with work surface of any size with half  height

partition should comprise of:

a) for 70 mm (of height 4' and thickness and minimum overall thickness of 70 

mm) made of : 

i) Structural members fabricated of 1.50 mm to 2.20 mm pure 100%  aluminium 

extrusion channel with epoxy / powder coating  min. of 40 to 50 micron. 

ii) Two sides of partition panels finished partially with 9 mm thick prelaminated particle 

board and in between space of 52 mm out of over all thickness of 70 mm to be kept 

vacant for universal data and cable management system. Partial panel may be  with 

glass panel of minimum thickness 5mm. for some areas for better visibility and 

lighting. 

iii) Box type raceways open able on both sides at bottom level and as required below or 

above table height for carrying electrical and data cables. Skirting covers of height 

120 – 130 mm with materials fabricated with prelaminated particle board of 

thickness 9mm. 

iv) Slots in vertical sides for horizontal wire management of cables. 

v) General: Trims finish –Aluminium epoxy coated with 40-50 micron. All metal 

sections,  cantilever brackets to hold the work tables and tops and aluminium profile 

finished in epoxy coating of thickness 45 to 50 micron of approved shade.

for 30 mm-  The entire structural frame viz. horizontals and verticals are made of 30mm 

thick high quality aluminum extruded interlocking sections. Semi-circular top and 

vertical trims are made of aluminum extrusions which are snap fit. Provision of dual 

management facility is available. As per the international standards corner caps and 

top caps are made of Zinc moulds. Levelers are provided to overcome unevenness 

in the flooring. Snap fit tiles compromises of 15 mm prelam board on both making 30 

mm thick over all, Magnetic Fabric board. 30mm snap fit panel fixtures are made of 

zinc moulds. The top, vertical and corner trims are available in standard powder 

coating finish of international standards.  ( Decor-x make )

for 60 mm-  The entire structural frame viz. horizontals and verticals are made of 60mm 

thick high quality aluminum extruded interlocking sections. Semi-circular top and 

vertical trims are made of aluminum extrusions which are snap fit. Provision of dual 

management facility is available. As per the international standards corner caps and 

top caps are made of Zinc moulds. Levelers are provided to overcome unevenness 

in the flooring. 60mm snap fit panel fixtures are made of zinc moulds. The top, 

vertical and corner trims are available in standard powder coating finish of 

international standards.  ( Decor-x make )

for 50 mm- The entire structural frame viz. horizontals and verticals are made of 50mm 

thick high quality aluminum extruded interlocking sections. Semi-circular top and 

vertical trims are made of aluminum extrusions which are snap fit. Provision of dual 

management facility is available. As per the international standards corner caps and 

top caps are made of Zinc moulds. Levelers are provided to overcome unevenness 

in the flooring. Snap fit tiles compromises of 4 mm prelam board on both side 

making 48 mm thick over all, Magnetic Fabric board . 50mm snap fit panel fixtures 

are made of zinc moulds. The top, vertical and corner trims are available in standard 

powder coating ( moon shell grey ) finish of international standards.