We offer Electromagnet, EMU-75 is useful in general laboratory and R&D labs. It has the most widely used 'U' shaped soft iron yoke. The soft iron is of a special quality, structurally uniform, well machined and finished to meet the rigid standards. The pole pieces are made from dead annealed soft iron blocks of the best quality available. They are well shaped, machined and finished. The air-gap is continuously variable up to 75mm with two way knob bed wheel screw adjusting system. Normally flat pole pieces are supplied. Tapered pole pieces can be supplied on special request. The coils are wound on non-magnetic formers with uniform layers of S.E. copper wire. The new and modern design of the coils provides good thermal conductivity characteristics and eliminates troublesome hot spots even at high magnetic fields.
Specifications of EMU-75
Pole Pieces: Φ75mm flat in EMU-75
: Φ75mm tapered to 25mm in EMU-75T
Field: EMU-75: 10.75KG at 10mm air gap
: EMU-75T: 17.5KG at 10mm air gap
Energizing Coils: Two, each having a resistance of approx. 13Ω
Power Requirement
*0-90Vdc, 3A, if coils are connected in series
*0-45Vdc, 6A, if coils are connected in series
Constant Current Power Supply DPS-175 is designed to be used with the Electromagnet, Model: EMU-75 as a constant current power supply to generate magnetic field up to 11KG.
Specifications of DPS-175
Current: 0-3A per coil Smoothly adjustable
Line Regulation: ±0.1% for 10% mains variation
Load Regulation: ±0.1% for load variation from 0 to max.
Display: 3½ digit, 7 segment LED display
Protection: Protected against overload, short circuit and transients caused by the load inductance.
Power: 220V 10%, 50Hz or 110V 10%, 60Hz as required
Weight: 13Kg.

We offer Electromagnet, EMU-75 is useful in general laboratory and R&D labs. It has the most widely used 'U' shaped soft iron yoke. The soft iron is of a special quality, structurally uniform, well machined and finished to meet the rigid standards. The pole pieces are made from dead annealed soft iron blocks of the best quality available. They are well shaped, machined and finished. The air-gap is continuously variable up to 75mm with two way knob bed wheel screw adjusting system. Normally flat pole pieces are supplied. Tapered pole pieces can be supplied on special request. The coils are wound on non-magnetic formers with uniform layers of S.E. copper wire. The new and modern design of the coils provides good thermal conductivity characteristics and eliminates troublesome hot spots even at high magnetic fields.
Specifications of EMU-75
Pole Pieces: Φ75mm flat in EMU-75
: Φ75mm tapered to 25mm in EMU-75T
Field: EMU-75: 10.75KG at 10mm air gap
: EMU-75T: 17.5KG at 10mm air gap
Energizing Coils: Two, each having a resistance of approx. 13Ω
Power Requirement
*0-90Vdc, 3A, if coils are connected in series
*0-45Vdc, 6A, if coils are connected in series
Constant Current Power Supply DPS-175 is designed to be used with the Electromagnet, Model: EMU-75 as a constant current power supply to generate magnetic field up to 11KG.
Specifications of DPS-175
Current: 0-3A per coil Smoothly adjustable
Line Regulation: ±0.1% for 10% mains variation
Load Regulation: ±0.1% for load variation from 0 to max.
Display: 3½ digit, 7 segment LED display
Protection: Protected against overload, short circuit and transients caused by the load inductance.
Power: 220V 10%, 50Hz or 110V 10%, 60Hz as required
Weight: 13Kg.