Listing ID #902081
Company Information
Ask for more detail from the seller
Contact SupplierC.R.I. 150 mm (6") Borewell submersible pumpsets are built with different materials of construction together with extremely hardwearing bushes which makes this pumpsets highly durable. Radial flow submersible pumpsets are supplied with stainless Steel impellers and stage casings and mixed flow pumpsets are supplied with LTB-2 and casted steel impellers to give better performance and longer life. The optimal design of impellers and diffusers offers best possible hydraulic efficiency. These pumpsets are powered by a water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked in stainless steel stator shell. Specially designed high performance thrust bearings (SS with Carbon) are used to withstand axial and down thrust loads with minimum wear and tear. Dynamically balanced rotor gives vibration free and noise free operation, thereby increases efficiency and life cycle of the motor.
Applications :
Salient Features :
Pumped Liquids : Clean, thin, non-aggressive, Non explosive, clear, cold, fresh water without abrasives, solid particles or fiber having the following characteristics
Power range | 1.1kW – 26 kW (1.5HP – 35HP) |
---|---|
Speed | 2900 RPM |
Version | 200 – 240V, Single Phase, 380 – 415V, Three Phase, 50 Hz, A.C. Supply |
Maximum total head | 503 m |
Maximum flow rate | 22.2 lps (80 m /h) |
Nominal outlet size in inches | 50, 65, 80 & 100 |
Degree of Protection | IP 58. |
Maximum outer diameter in mm | 143 & 145 |
Direction of Rotation | Clockwise from driving end. |
Thrust Load | 1500 lbs. 1.1kW to 4.5kW, 3500 lbs. 5.5 kW to 15kW, 6000 lbs.18kW to 26 kW |
Minimum cooling flow along the motor | 0.15 m/sec |
Type of duty | S1 (Continuous) |
Method of starting | Single Phase, Capacitor Start and Capacitor run (CSCR), Three Phase, DOL upto 5.5 kW, SD upto 26 kW. |
Maximum starts per hour | 12 times |
MATERIAL OF CONSTRUCTION OF PUMP | |
Part Name | Material |
Check Valve housing | CI / S.S 304 |
Check Valve Seat | Nitrile Butyle Rubber |
Diffuser Chamber | SS 304 & Cast Iron |
Impeller | SS, LTB 2 & Casted SS |
Suction Inter Connector | CI, SS 304 |
Inlet screen | SS 202 |
Pump shaft | SS 410 / 431 |
Cable guard | SS 202 |
Coupling | SS 410 |
MATERIAL OF CONSTRUCITON OF MOTOR | |
Upper and Lower Housing | Cast Iron |
Stator Shell | SS304 |
Shaft | SS 410 & EN 9 with 410 |
Journal Bushes | Leaded Bronze / Graphite Carbon |
Thrust Assembly | SS 420 and Graphite Carbon |
Maximum liquid temperature | 33 oC |
---|---|
Permissible amount of sand | 50g/m3 (max.) |
Chlorine ion density | 500 ppm (max.) |
Allowable solid | 3000 ppm (max.) |
Specific Gravity | 1.004 (max.) |
Hardnesws (drinking water) | 300 (max.) |
Viscosity | 1.75 x 106 m2/sec (max.) |
Turbidity | 50-ppm silica scale (max.) |
PH value | 6.5 to 8.5 |