Antique Base Wall Mortar

“Antique Wall Mortar” is a water resistant Luster wall coating for interior as well as exterior use.
“Antique Wall Mortar” make building components totally water proof.”Antique Wall Mortar” is totally crack proof with high bonding which gives colour resistancy as well as weather proofing. Get luster finish
with UV resistance & eco friendly with high bond luster coating.

Salient features of “Antique Wall Mortar”
*Make building component Totally Water
*Made wall totally crackproof with high bonding.
*Colour resistancy as well as Weatherproofing.
*Use for interior as well as exterior coating.
*Get Luster Finish With UV Resistance and Eco friendly’’Antique Wall Mortar”

Application Procedure
Remove all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and clean water. The substrate should be clean, free from dust, grease and loose materials.
Dry and absorbent surfaces should be moistened with sufficient quantity of clean water.
Mix “Antique Wall Mortar” with 60-65% clean water slowly to make paste. Continue the mixing for 10-15 minutes with putty grind machine till a uniform paste is formed. After thoroughly mixing “Antique Wall Mortar” apply the first coat with Antique base mortar on already moistened wall surface from bottom to upward direction uniformly with the help of putty blade. This would ensure less wastage and proper finish. After drying of first coat of Antique base mortar just rub the surface gently with west sponge or rub the surface very gently with the putty blade in order to remove the loose particles. Allow the surface to dry for atleast 24 hours and then apply second coat of with Antique finish mortar Leave the surface to dry completely. After drying of second coat remove marks if any with the help of moist sponge or rub the surface very gently with the putty blade. Leave the surface to dry preferably for overnight. Always prepare a required quantity of putty and use it within 2-3 hrs. of mixing with water The total thickness of the coats should be limited to maximum 1.5mm. It is not essential to rub the surface done with “Antique Wall Mortar”, however if you need to remove unevenness before applying any kind of paint/distemper, gently level the walls/ceiling surface with very fine water proof emery paper of not less that 500 number to get a glossy white surface.

Precautions During Application
Mixing of “Antique Wall Mortar” is very important and hence extreme care is to be taken for proper and thorough mixing with hand or mechanical stirrer in order to get best results. “Antique Wall Mortar” should be done over fully cured surface. It is recommended not to rub “Antique Wall Mortar” strongly and harshly with rough emery paper. This breaks the film formed over “Antique Wall Mortar”, which decreases the water repellency properties. The total thickness of the coat should be limited to maximum 1.5mm. In case of fresh concrete/mortar surface it is recommended that two coats of Antique Base Mortar be apply before application of “Antique Wall Mortar”.

Coverage
The coverage area of “Antique Base Wall Mortar” on smooth normal mortar wall is 25 to 30 Sq. Ft/Kg/mm
The coverage area of “Antique Finish Wall Mortar” on smooth normal mortar wall is 35 to 40 Sq. Ft/Kg/mm
The coverage area, however, will depend upon the quality of the substrate.

Note
Generally the cause of efflorescence on the walls surface is the brick masonry, which is due to the quality of bricks, sand and water, If the effect of efflorescence on the brick masonry seems to be very high then proper care should be taken to control the efflorescence. The efflorescence problem on brick masonry if exists impairs the bonding of “Antique Wall Mortar” as is with any other product.
* for High Effected efflorescence walls Contact our Customer Care for solution.

Packing
“Antique Base Wall Mortar” is available in 20Kg Pack.

“Antique Finish Wall Mortar” is available in 10Kg Box Pack.