Nylon Proximity Switches, For Magnetic Use, Voltage : 200VDC

We are a quality-conscious firm and make sure that our offerings are prepared using the world-class raw material and work methods. Also, the material is sourced from the trusted places only. All thanks to our smart inventory management owing to which safe and quick deliveries are furnished by us. It is also RPM Sensor.

Operation :
Before connecting power supply insure that you are connecting I/P voltage to the right terminals. On application of proper power supply & input sensor. The instrument will display set (range) value in lower display and actual RPM in upper display.
Key Operation :

• By pressing SET key, Digit fleshing ON upper display. The fleshing can be shift to next digit by pressing
• Shift key.
• By pressing UP key fleshing digit value can be change from 0 to 9, and again press SET key for store modified value.

Relay Operation :

• Relay : Relay OFF when RPM is less than Set value & ON
• when is more than Set value and 
• RPM : Vice-versa.

Terminal details :

• P (phase)
• Note :  supply 220 volt AC  @ 50/60HZ or /
• 24v/15VDC
• N (Neutral)
• 5 : NO2
• 6 : NC2
• 7 : P2(POLE2
• 8 : NO1
• 9 : NC1
• 10 : P1(POLE1)
• 16 : -mA (4-20 mA output)
• 17 : +mA  (4-20 mA output)
• 18 : -12v (sensor)
• 19 : +12v(sensor)
• 20 : +o/p (PNP-NO/NC)
• 21 : - o/p (NPN-NO/NC)

Indication :

• I/P LEDstart blinking as the sensor sense the pulse.
• O/P LED get ON when relay goes ON.

Spefications :

• Main (auxiliary supply) : 220vAC @50Hz / 24 VDC/15V DC
• RPM Range : 0000-9999
• Heat or cool function : Settable for relay
• Output (Analog) : 4-20mA
• Control Relay : one pair normallyopen potential free contact  :  @ 5A at 240v AC 
• Senor : PNP-NO/NC or NPN-NO/NC proximity switch
• Operating temp. : 0 dec. –  50 dec
• Overall size : 72x72x120 mm (HWD )
• Panel cutout : 67X67mm(WXH)

Parameters :

• By using Set key following parameters can be scroll.
• RL1 : 0000 -9999
• Range : 0000 – 9999 (set higher range of 4-20mA)
• RL2 : 0000 - 9999
• Scale : 0000 – 4.999 (multi/div. factor parameter)
• Hc1 : 1 -  2  (Heat / cool) parameter for relay RL1
• Hc2 : 1 -  2 (Heat/ cool) parameter for Relay RL2
• Teth : 1-99 setable
• Over : Over message display when RPM over than set range parameter
• RL 1&2:Set value of RPM. If actual RPM Lower than Set value Relay will be ON and ifactual Values cross the Set value. Relay goes to change its control.
• Range : This is setting value for retransmission output 4-20mA.
• Scale :  This parameter is selectable for multiplier and divider factor for RPM display
• Actual rpm x scale value =result (manipulated RPM)
• Example1: 1800( actual rpm ) x .834=1501 rpm (result)
• Example 2. : if actual RPM  3000 but you want display 1535 RPM then
• Actual rpm/ required rpm= result(it is the multiplier value)
• Hc 1&2 : In this parameter user can be select relay position N/O N/C, If value 1 setthen N/O, if value 2 set then  N/C
• Teeth  : in this parameter user can be adjust input teeth or pulse.

Configuration :
Pressset key  for 5 seconds,display rl1 again press set key now display  last load value, if change then use shift key for digit selection and up key use for 0 – 9 value again press set key now modified value store and display rl2 same process apply for all parameters. If user not touch any for some time then system automatically exit from configuration mode. The system can be exit from configuration mode if user press shift key at the time rl1 display.