Our Products

Scaffolding And Scaffolding Parts
2 Products available
- Telescopic Prop
- Telescopic Span
Industrial Coupler
2 Products available
- Right Angle Coupler
- Swivel Coupler
Brackets
1 Products available
- Beam Brackets
Scaffolding Frame
1 Products available
- Cantilever Frame
Hardware Fittings And Accessories
1 Products available
- Adjustable Base Plate
Industrial Jacks, Lifts & Winches
1 Products available
- Adjustable Fork Head Jack
Scaffoldings
1 Products available
- H-Frame Scaffolding
Wall Decor
1 Products available
- Wall Form Panel
Scaffold Planks
1 Products available
- Floor Forms
Others Products 6 Products available

Our Products

Our Complete range of products are Pallet Fork, Cuplok Verticals, Cuplok Horizontal, Bridging Horizontal and Dropheads.

Pallet Fork

Features Fork width can easily be adjusted, The forks are made of high tensile forged steel, Precise steering and drive control

View Complete Details

Ask Latest Price & Details

Cuplok Verticals

POLYTECHVertical are complete out of 40 NB B Class tube verify to 1S 11611239 Pair of cups are produce at 500 mm cc, but cups at 1000 mm cc are obtainable in usual size of 3.0 mtr, 2.5 mtr, 2.0 mtr, 1.5 mtr, 1.0 mtr & 0.5 mtr. imperfect sizes can be supplied on demand.

View Complete Details

Ask Latest Price & Details

Cuplok Horizontal

POLYTECHHorizontals, make out of 48.3 OD scaffold tube verify by IS 11611239 with fake end blade welded at equally ends to tube and are obtainable in length of 2.5 mtr, 2.0 mtr, 1.8 mtr, 1.5 mtr, 1.25 mtr and 1.0 mtr.

View Complete Details

Ask Latest Price & Details

Cantilever Frame

This grade is designed for helping the formwork & scaffold at lump limits they are obtainable in two sizes of 1.5 mtr & 1.0 mtr lift. It is situated in cup joints.

View Complete Details

Ask Latest Price & Details

Bridging Horizontal

The Bridging horizontal is produced to make a working place or stage where a obvious span of above 2.5 mtr to 5.0 mtr is necessary by the chief scaffold run.

View Complete Details

Ask Latest Price & Details

Beam Brackets

To hold drop beams, eliminate the requirement of further rows of hold up below the beams, the beam bracket might be situated on uppermost cup joints.

View Complete Details

Ask Latest Price & Details

Adjustable Base Plate

For utilize in rolling ground situation & where it is necessary for building up for elevation variation when used beneath supports. obtainable in 32 & 36 , changeable length of 350 mm & 450 mm with adjustment by way of screw upto 275 mm & 350 mm correspondingly.

View Complete Details

Ask Latest Price & Details

Adjustable Fork Head Jack

A weighty duty fork head (U-Head) which provide modification able to 350mm to meet a extensive variety of unreliable height. It is designed to produce considerable bearing places. It has a usual acme thread and obtainable in 32 & 36 .

View Complete Details

Ask Latest Price & Details

H-Frame Scaffolding

Consists of rigid welded border make out of 48.3 OD pipe in two plumb and two horizontals. The frames are connected by scissor (Cross) Braces made out of 25 NB NB pipes via the pin welded on frame and secure in spot care of clips.

View Complete Details

Ask Latest Price & Details

Telescopic Prop

Size 1P, 2P, 3P, 4P

POLY TECH telescopic prop are mainly ideal and inexpensive process of hold for all type of formwork to slab, beams, walls and column.

View Complete Details

Ask Latest Price & Details

Telescopic Span

Size ESO-ESI, SO-ESI, SO-SI

POLY TECH Telescopic span is outcome of a lot of years of knowledge in building industry. Their capacity to add in different length modification.

View Complete Details

Ask Latest Price & Details

Right Angle Coupler

One part load coupler use for involving two scaffold tubes at correct Angle or 90 Pressed form elevated rating steel, check for bend & slip.

View Complete Details

Ask Latest Price & Details

Swivel Coupler

A one portion freight bearing coupler for between any two & scaffold tubes at some through 360 . press from elevated status steel and check for distortion & slip.

View Complete Details

Ask Latest Price & Details

Wall Form Panel

Wall formwork is perfect for weighty and light duty versatile formwork and is appropriate for vast kind of cast in situ concrete construction such as walls, adequately stiffened with longitudinal stiffener, foundation, Rectangular or circular tanks, Dams, Bridges, beams, column, etc. Made out of 12G10G, MS sheet with 45mm 50mm deep Angle frame.

View Complete Details

Ask Latest Price & Details

Dropheads

The quick action drop head supplied complete with nuts and bolts. Is designed to fit on Cuplok scaffolding.They allow infills and beams to be struck re-used after only 3 or 4 days, leaving the support in position for the remainder of of the curing period of the concrete slab.

View Complete Details

Ask Latest Price & Details

Floor Forms

PLOY-TECH floor are make out of 14G12G press bent sheet and light in heaviness as compare to the conservative centering plate obtainable in the marketplace. PLOY-TECHfloor forms are easygoing weight sufficient rigidity gives excellent concrete finish, cuts labour cost and gives a perfect solution to slab shuttering problems.

View Complete Details

Ask Latest Price & Details

Adjuster Floor Form

PLOY-TECH adjuster floor forms are too the vital part of floor form, which is use to evade imperfect slab formwork, thus eliminate of timber in slab formwork.

View Complete Details

Ask Latest Price & Details