Nashik, Maharashtra, India
Verified
Add Review
Our Products
Softening Point apparatus is used for locating softening point of bituminous materials. Our product is manufactured as per IP58 and IS 1205-1958 standards. Softening point is that temperature at which the sample under test becomes soft enough to allow a steel ball of specific dimensions to fall a required distance under test condition. The apparatus consists of glass beaker, rings and ball guides, hand stirrer.
Our range of product includes:
However, we also provide these optional accessories along with product:
Features:
| Accessories Provided |
| Acrylic Drums (2). |
| Special Locking Magnetic Tray (2). |
| Operating Manual (1). |
Bulk Density Apparatus Bulk Density Apparatus is specially designed to study the packing down of powder beds of different pharmaceuticals and chemicals powders, flakes, pellets, granules and other bulk substances. Bulk Density is an essential test required in the process of tablet manufacturing, Capsule filling and cosmetic manufacture.
Aniline point apparatus as per IP 2 & IS 1448 (p-3), ASTM D 611 method a a complete with jacket (without thermometer) aniline point apparatus as per IP 2 method b is 1448 (p-3), ASTM D 611 by thin film method b electrically heated with motorized stirrer (without thermometer) spare tap spare contraction chamber spare metal stirrer aniline point apparatus as per IP 2 1977 method d by U-tube method electrically heated with motorized stirrer (without thermometer) spare ‘U’ tube dean and stark apparatus for estimation of moisture in lubricating oils as per IP-74, ASTM D 95 is 1448 (P-40). with one 10 CC receiver flask, condenser with clamp holder and elect. Heater with energy regulator.
Product Description
Features:
Accessories Provided:
Specifications:
Melting Point Apparatus is usable to estimate the Melting Point of chemicals, Pharmaceuticals, Foods etc., This is very useful to determine the melting point of any substance. Max Temp. up to 350°C. Consist with aluminum cylindrical block for heating, Radial holes admits a thermometer and glass capillary. Temp. Controlled by energy regulator. Regulator fitted to the unit and with high, low heat switch.
1) SINGLE SPEED
2) TWELVE SPEED
The apparatus comprises of the following :
Loading Unit: Supplied with loading yoke with direct and lever for applying load. Normal stress capacity 8Kg/Sq.cm. Load is applied either directly or through a counter balanced detachable lever. Provision is made for the load to be applied either through a steel ball recessed in the loading pad or direct through a boss on the pre calibrated loading. Yoke. The loading unit is provided with V strips and roller strips for frictionless movement of shear box housing.
Consists of loading unit, shear box assembly for 60 mm x 60 mm x 25 mm complete with two halves of loading pad, one base plate. All made of gunmetal with two porous stones. Share box housing of gunmetal, specimen Cutter of steel with set of weight to give normal stress of 3 kg/cm2. Through lever as follows.
To give kg/cm2. Qty.
0.05 4Nos.
0.1 1No.
0.2 1No.
0.5 3Nos.
1.0 1No.
Multiple reversal type, Motorized, Single speed , electrically operated to give a single constant rate of strain of 1.25mm/min. Suitable for 230v. A.C. Without dial gauge and proving ring. AS PER IS:2720 (PART VIII)
OR
Unit is electrically operated to give the following 12 rates of strains. 1.25, 0.625, 0.125, 0.05, 0.01, 0.005, 0.002, 0.001, 0.0004 and 0.0002mm/min. The apparatus is suitable for operation on 230 volts single phase A.C. supply. Without dial gauge and proving ring.
OPTIONAL ACCESSORIES:
Dial Gauge 0.01 mm x 25 mm travel
High sensitivity proving ring 200 kg. fitted with 0.002 mm dial gauge with our calibration certificate in a case.
Shear box complete with two plain gripper plates, two perforated gripper plates, two porous stones, one top loading pad, one base plate and U-bracket. 60x60x25mm.Made of Gunmetal.
Spare Housing.
Field CBR apparatus.
It is useful in determining the load carrying capacity in the field when in place density and water contents are such that the degree of saturation is 80% or greater, when material is cohesion less and course grained. Such that it is not effected by changes in water contents and when the material has been in place for considerable time. The loading is effected by means of a mechanical load frames which can be fixed to the under side of a truck.
Specifications: mechanical screw loading jack, 10, 000 kg. Capacity with u-bracket and swivel head. Penetration piston, 50mm dia. Threaded at the upper end. Extension rods consisting of 2 lengths 5cm. 2 lengths 10cm, 1 length 30cm, 1 length 50cm and 1 length 100cm, used as spacers between the proving ring and penetration piston. The lengths are machined from steel tubing. Connector set has eight connectors for coupling the penetration piston and proving ring assembly either directly or through extension pieces. Dial gauge support of seamless pipe construction. It stands 30 cm high and 45 cm wide at the base. Provided with a quick release screw type clamp capable of sliding and locking anywhere along 2 meter length of the bridge. Supplied with annular metal weight 5 kg, 250mm dia with 53mm dia central hole, slotted metal weight 5 kg. 215mm to 250mm dia with 53mm dia slot, 2 nos. Slotted metal weights, 10 kg, 215mm to 250mm dia with 53 mm dia slot 2 nos. Dial gauge 0. 01mm x 25mm. High sensitivity proving ring 5000 kg capacity with calibration chart & carrying case.
Moisture contents at which soil has smallest plasticity is called limit. For determination purpose plastic limit is defined as the water content at which a soil will just begin to crumble when rolled into a thread of 3mm. dia.
Salient Features
Specifications: The complete set consists of one each:-
1. Glass plate 20 cm x 115 cm having ground ends and one side frosted.
2. Brass or stainless steel rod 3 mm dia x 150 mm long.
3. Flexible spatula.
4. Set of 6 moisture containers.
5. Porcelaine basin 150 mm dia.
6. Plastic wash bottle 500ml.
We are manufacturers and exporters ofSlump Conethat finds application in determining the consistency of freshly mixed concrete, where the maximum size of the aggregate does not exceed 38 mm. This equipment consists of one slump cone with handles and foot pieces and ensures hassle free performance at all levels of operations.
Features:
The slump cone has internal dimensions 20 cm dia at base 10 cm top dia and 30 cm height
Foot pieces can be fixed to the clamps on the base plate
The base plate has lifting handle for easy transportation
One graduated steel rod 16 mm dia x 600 mm long, rounded at one end and graduated in mm, is also supplied
We offer Vicat Needle Apparatus that is widely used in determining the normal consistency and setting time of cement. The test is undertaken by mixing cement with water and then measuring its resistance to penetration of a standard probe at varying intervals of time, until a certain value is reached. This equipment is very rugged and hence can withstand the harsh weather conditions. We offer this apparatus to our clients from construction industry at very competitive rates.
Set of Accessories:
We are manufacturer, exporter, trader, supplier & distributor of Friability Test Apparatus.
Soxhlet Apparatus, quick surface heating save extraction time. Fiber glass hand knitted heating surface having nichrome heating elements. Body made up of M.S. with powder coating. The housing has two retort rods and a cross bar. This apparatus has a built in regulator which controls the heater Heating elements have a individual regulators Pilot lamp to indicate working of the elements. To work on 230 Volts AC Only.
Manual Blood Pressure Monitor(B.P. Appratus Mercury) Traditional desk mercurial sphygmomanometer in the aluminum painted case with self Locking device, with adult Velcro cuff and metal D ring, Inter5nal graduated glass scale With inside diameter of 3.5 mm and a clear reading glass scale. On and OFF mercurial Tap for measuring range 0 to 300 mmhg air releases at closed tap max 4 mmhg per minute Graduated scale from 2 mmhg to 2 mmhg with bigger botches graduated every 10 units Single Packing in carton box.
This apparatus is suitable for determining the close cup flash point of Petroleum and mixtures according to IP 33 & IP 170 and also IS 1448 (Part I) 1985 (P:20). It is suitable for oils whose flashes below 70C. It is supplied with oil cup, cover fitted with stirrer, thermometer socket S.S. Water Bath, Stand. An electric heater is fitted at bottom for operation on 220 Volts AC Circuits.Following Models are available Abels Flash Point Apparatus electrical heating with Energy Regulator Control Oil Test Jet. Abels Flash Point Apparatus electrical heating with Energy Regulator Control & Concealed Hot Plate Oil Test Jet. Abel Flash Point Apparatus with VOLTAGE VARRIER CONTROL Oil Test Jet. Abel Flash Point Apparatus with Voltage varrier, digital temp. Indicator oil test jet. abel flash point apparatus with voltage varrier, digital temp. Indicator Gas Test Jet with geared FHP. Elect. Driven Stirrer (120 R.P.M) Abel Flash Point Apparatus Temp. Range -18C to +70C with REFRIGERATION SYSTEM as per IP-70 with Oil Test Jet & Gas Test Jet combine system. With digital temperature. Indicator and FHP motor stirrer.
Optional accessories:
Supported by our latest technology and robust team of experts, we are considered as pioneers in manufacturing premium grade Cloud and Pour Point. These scientific instruments are ideallyused in Oil industries to test the pour point in minimum temperatures at which, the oil is not able to flow.
We ensure to conduct stringent quality tests on the entire product range, based on industry set norms. With our client friendly payment policies and transparent business dealings, we have attained a good reputation in the markets.
Temperature ranges:
0C -17C, -34C -51C for four tank model. -70C to 0C for Single tank model.
Following are the Technical Specifications of Cloud and Pour Point:
Model:
Temperature Controller:
Construction:
Refrigeration System:
Power Supply:
DEAN & STARK APPARATUS FOR ESTIMATION OF MOISTURE IN TAR & BITUMENS As per IS 1211 ASTM D 2448 IP-291. The apparatus consist of 500 ml heat resistant glass with neck having ground glass joint, a condenser made of heat resistant glass as per fig. 2 of IS 1211, receiver also made of heat resistant glass with ground glass joint leading to the flask and graduated tube. Capacity of receiver will be 2 or 10 ml
This is used for determining drop point of greases . It is an indication of the critical temperature of the solid or semi solid to the liquid state. The apparatus consists of brass sleeve and case with metal cup and a glass boiling tube with cork fitted to a bath (Beaker) is provided . A stirrer is also provided in the bath.
Optional Accessories:
Flash & Fire Point Apparatus used for determining the flash point of fuel oils and lubricating oil, bitumen other than cutback bitumen and suspension of solids in liquids, having a flash point above 49C. For determination of (OPEN CUP) flash & fire points of petroleum products and other liquids except fuel oils and those materials having an open cup flash below 79 C (175 F) as per specification IP 36 and IS 1448.The apparatus consists of brass test cup with handle removable cup cover with the spring operated rotated shutter having oil test jet flame device, stirrer with flexible shaft. The assembly rests in Air Bath which is covered with dome shape metal top. The cup assembly is positioned in a cast iron air bath, fitted with a chrome plated brass top having electric heater with temperature controller. Suitable for operation on 220V, 1Ph, 50Hz AC Supply.
Suitable for Operation on 220V, Single Phase, 50Hz, AC Supply
Features:
Specifications
Optional special software for transferring data to local PC.
We are a well known name in this domain who is engaged in offering a wide range of Smoke Point Apparatus. The offered range is manufactured using premium grade components and sophisticated technology in adherence with the set international standards. This apparatus is used to determine the smoke point of kerosene and aviation turbine fuel by measuring the maximum flame height prior to smoke formation and comparing the results with those of known standards. We are providing the entire range in different designs and sizes as per our clients specific demand.
Features:
Product Description
To know the quality of paint on the pre-painted sheet therefore, samples are cut and deep drawn according to Erichsen Principle to determine the depth to which they can be drawn before the paint cracks.
Conforms to German Standards DIN 53156 and ISO Recommendation R149.
Pressing the clamped test piece into a die by means of a ball or penetrator with a spherical end until rupture commences; measuring the depth of the cup.
The term Opacity Chart refers to charts on which the test pattern is a simple combination of black and white areas, large enough for wide aperture reflectance instruments, as well as for visual opacity and color observations.
Sag Index used to determine the level of Wet Film Thickness of Paint Film. It will help to evaluate visually for sag resistance of coating. The instrument is commonly used in laboratories for quality control and experimental purposes for various fields like Paint, Ink & Powder Coating Industries. Our range is available with seven pairs of gaps for leveling assessment 50, 75, 100, 125, 150, 175, & 200 micron.
Features:
Product Description
Features:
Features:
Features:
Applications:
Specifications:
| Parallel Port Printer Interface for Dot Matrix Printer |
| Compliant with USP Specifications |
The Dairy Industry, trade and the public analysts in India prefer to use The Gerber Method for the rapid and routine determination of Fat in milk and milk products, when relatively large number of samples has to be analyzed at a time. The use of apparatus standardized and calibrated according to the conditions and materials available in our country and the adoption of uniform methods of determination of fat will enable one to obtain comparable results, within a reasonable degree of accuracy.
Butyrometers
Milk Butyrometer 0-8%
Milk Butyrometer 0-10%
Cream Butyrometer 0-70%
Cheese Butyrometer 0-40%
Butter Butyrometer 0-90%
Milk Powder Butyrometer 0-35%
Ice Cream Butyrometer 0-20%
Skim Milk Butyrometer 0.5%
It is made as per IP 13, ASTMD-159 specifications. It is useful to determine amount of Carbon residue when an oil is evaporated under specified conditions. The Carbon residue values of crude oil, residuum etc. These are useful in the manufacture of various lubricants. The apparatus consists of spun sheet iron crucible 25 cc Capacity, Sheet Iron hood and sheet iron block on a stand gas humor.
