Payal Industries

Thakkarbapa Nagar, Ahmedabad, Gujarat

This Machine is available in PE, PM & PI series Standard Features for PM Series 5 Point double Toggle clamping system of steel casting Mould opening and clamping in three stage Manual mould setting gear arrangement Automatic lubricating system in Toggle side Single stroke hydraulic ejector Square tie bar distance with large mould height High tensile, hard-chrome plated tie bar Electrical interlocks in front and rear safety guards Ceramic Band heater High torque hydraulic motor for screw drive Automatic suck back system Two Stage injection speed Gas-nitride screw barrel with standard L/D Ratio Injection movement is actuated by two hydraulic cylinders, for perfect alignment to the clamp unit Injection unit siding on hard-chrome steel treated ground tie bars. Easy access to the screw is ensured Stainless steel hopper with magnetic grill with swiveling system to permit the easy change of the material Limit switch for stroke control MCB Control for each heating zone Star Delta starter for pump motor 200 TO 650T Overload protection for pump motor CLAMPING BIDE     5 Point double Toggle clamping system of steel casting Mould opening and clamping in three stage Manual mould setting gear arrangement Easy & fast lubricating system Square tie bar distance with large mould height High tensile, hard-chrome plated tie bar Electrical interlocks in front and rear safety guards   INJECTION BIDE     Digital temperature controllers and timers High torque hydraulic motor for screw drive Automatic suck back system Two Stage injection speed Gas-nitride screw barrel with standard L/D Ratio Injection movement is actuated by Twin hydraulic cylinders, for perfect alignment to the clamp unit Injection unit siding on hard-chrome steel treated ground tie bars. Stainless steel hopper with magnetic grill with swiveling system.   HYDRALIC & ELECTRICAL     Resiliently mounted hydraulic pump Suction Iine oil filer Limit switch for stroke control MCB Control for each heating zone Star Delta starter for pump motor 200 TO 650 Tonnes Overload protection for pump motor Standard Features for PI Series 5 Point double Toggle clamping system of steel casting with steel link and steel bushes with tempered steel pins Hydraulic ejector through plate with multiple ejector cycles through nine strokes Multiple point automatic lubricating system Clamp closing and clamp opening profile with programmable and independent strokes and speeds Low pressure mould protection with high mould safety Freely programmable control of max. 2 core pulls and air for the control of max. 1 valve Mould opening and clamping in Four stages Mould setting gear arrangement by Hydro-motor Square tie bar distance with large mould height High tensile, hard-chrome platted tie bar Electrical interlocks in front and rear safety guards Ceramic heater High torque hydraulic motor for screw drive Automatic suck back system Four stage injection and four stage holding time Cold start protection Gas-nitride screw barrel with standard L/D Ratio Injection movement is actuated by two hydraulic cylinders, for perfect alignment to the clamp unit Injection unit sliding on hard-chrome steel treated ground tie bars Stainless steel hopper with magnetic grill mounted on a swiveling system Injection speed, pressure and holding time profile on 7 steps Proportional valve for pressure and flow control with electronic feedback Suction and return oil filter Component easily accessible for maintenance purpose Resiliently mounted hydraulic pump Sealed oil tank with oil temperature 24 Volt DC solenoid valve Clamping and injection strokes are monitor by linear transducers M C B Control each heating zone Star Delta starter for pump motor 200 TO 650T Overload protection for pump motor  

LAMP UNIT       5 Point toggle clamping System Of steel Casting with steel link and Steel pin. Hydraulic ejector through plate with multipal ejector cycles up to 9 strokes. Multiple point automatic lubrication system. Clamp closing and clamp opening profile with programmable and independent strokes and speeds. Low pressure mould protection . Freely programmable control of max.2 core pulls and air for the control of max.1 vaves.   INJECTION UNIT       Injection movement is actuated by two hydraulic cylinders for perfect alignment to the clan unit. Injection unit sliding on hard chrome steel treated, groung tie-bars easy access to the screw is ensured by the swivelling movement. Gas nitride screw barer with standaed l/d ratio. Stainless Steel hopper with magnetic grill mounted on a swivelling system to permit easy change of material. Injection Speed, pressure and holding time profile on 7 steps. Cold start protection. HYDRAULIC SYSTEM       Components easily accessible for maintenance purposes. Suction and delivery oil filters. Proportion balves for pressure and delivery control with electronic feed-back. Sealed oil tank with oil temperature Control. Resiliently mounted hydraulic pump. OPTIONAL FEATURES       Core pulls Air Ejector with Time Stop Machine Timer Photocell with Drop-Out Mould Temperature Control Hydraulic Shutoff Nozzle Robot-interface Oneumatic Gate Variable Pump Unscrewing Device Accumulator for High Speed Injection.

5 Point double Toggle clamping system of steel casting Mould opening and clamping in three stage Manual mould setting gear arrangement Automatic lubricating system in Toggle side Single stroke hydraulic ejector Square tie bar distance with large mould height High tensile, hard-chrome plated tie bar Electrical interlocks in front and rear safety guards Ceramic Band heater High torque hydraulic motor for screw drive Automatic suck back system Two Stage injection speed Gas-nitride screw barrel with standard LD Ratio Injection movement is actuated by two hydraulic cylinders, for perfect alignment to the clamp unit Injection unit siding on hard-chrome steel treated ground tie bars. Easy access to the screw is ensured Stainless steel hopper with magnetic grill with swiveling system to permit the easy change of the material Limit switch for stroke control

5 Point toggle clamping System Of steel Casting with steel link and Steel pin. Hydraulic ejector through plate with multipal ejector cycles up to 9 strokes. Multiple point automatic lubrication system. Clamp closing and clamp opening profile with programmable and independent strokes and speeds. Low pressure mould protection . Freely programmable control of max.2 core pulls and air for the control of max.1 vaves.