Our Products
Tube Mill
2 Products availableWire Forming Machinery
2 Products availableGarden & Outdoor Furniture
2 Products availableIndustrial Machinery
1 Products availableConstruction Machines
1 Products availableMachines And Equipments
1 Products availableRoll Forming & Bending Machines
1 Products availableDraw bench for ferrous & non-ferrous Tubes, Wires & Rods | ||||||||||
Rotary Draw Bench for drawing tubes in coil form up to 25 mm OD | ||||||||||
Over 120 installations in lndia & abroad | ||||||||||
| ||||||||||
Toggle action type pneumatic tube gripping & hooking system for positive gripping | ||||||||||
Mechanized trolley reversing arrangement | ||||||||||
Die head holder mounted on spherical seat for better straightness in the drawn tube | ||||||||||
Riveted construction of chain. Heat treated & ground link & pin | ||||||||||
Single or Double plug rod system as per customer's requirement | ||||||||||
Pneumatically operated discharging arms for automatic tube collection | ||||||||||
Mechanised Mother Tube singling & feeding arrangement | ||||||||||
PLC based automatic control with variable speed drive |
Model Name | Pull Capacity | Typical Mother Tube ODxThk Combination (mm)* |
PARTH 5 DB | 50KN | 32x1.5 - 25x2.0 - 20x2.5 |
PARTH 10 DB | 100KN | 38x2.5 - 32x3.0 - 25x4.0 |
PARTH 20 DB | 200KN | 51x3.6 - 45x4.0 - 38x5.0 |
PARTH 30 DB | 300KN | 76x4.0 - 65x5.0 - 51x60 |
PARTH 40 DB | 400KN | 90x4.0 - 76x5.0 - 65x6.0 |
PARTH 60 DB | 600KN | 141x4.5 - 115x5.5 - 90x7.0 |
PARTH 80 DB | 800KN | 141x6.0 - 115x7.5 - 90x10.0 |
PARTH 100 DB | 1000KN | 168x6.0 - 141x7.0 - 115x9.0 |
PARTH 120 DB | 1200KN | 168x7.0 - 141x8.5 - 115x11.0 |
PARTH 150 DB | 1500KN | 194x7.5 - 168x9.0 - 141x11.0 |
Tube Straightening MachineFor Ferrous & Non Ferrous Metals. | ||||||||||
Over 100 installations in lndia & abroad | ||||||||||
| ||||||||||
3 x 3 skew roll design to achieve 1 in 1500 straightness | ||||||||||
5 x 5 skew roll design to achieve 1 in 3500 straightness | ||||||||||
M.S. Fabricated & duly stress relieved top & bottom main frames | ||||||||||
All the guiding holes in main frames for roll brackets & supporting columns machined in single setting | ||||||||||
Single piece integrated roll bracket design | ||||||||||
Rolls supported on two matched pair taper roller bearings on each side. Straightening machine for tube in coil form
|
Hydraulic testing machine suitable for stainless stell and carbon steel longitudinally welded tubes | ||||||||||
Custom made design to suit requirements of water and gas tubes to Oil country tubes | ||||||||||
| ||||||||||
Specially designed sealing arrangement for high pressure testing | ||||||||||
PLC controlled Auto & Manual cycles | ||||||||||
Quick changing type tooling for quick size change | ||||||||||
Testing pressure range from 200 to 600 atmosphere | ||||||||||
Heavy and rugged heads fabricated from tested carbon steel | ||||||||||
Selection of Power pack and intensifier from most standard and dependable sources | ||||||||||
Suitable for tube length ranging form 4 meters to 8 meters. Easy & quick length change through adjustable moving tailstock | ||||||||||
Single or multi-head design to suit different production quantum requirements . |
Model Name | Tube Size Range* | Pressure | |
Min O.D. | Max O.D. | (bar) | |
PARTH 170 HSTB | 50 | 170 | 200 |
PARTH 220 HSTB | 75 | 220 | 400 |
PARTH 220 HSTB-S | 115 | 220 | 600 |
PARTH 220 HSTB-E | 75 | 270 | 400 |
Low cost machine with high productivity | |
Most suitable for small diameter tubes | |
No end loss as swaged end is prepared through series of hammer stocks | |
2 Jaw type & 4 Jaw type arrangement for various diameter tubes. |
Model Name | Tube Size Range* | Tube Thickness* | ||
Min O.D. | Max O.D. | Min | Max | |
PARTH 2 SW-R | 0.6 | 0.3 | - | 0.2 |
PARTH 4 SW-R | 2.0 | 4.0 | - | 0.3 |
PARTH 10 SW-R | 2.5 | 9.5 | - | 0.5 |
PARTH 22 SW-R | 6.0 | 22.0 | 0.7 | 0.2 |
PARTH 32 SW-R | 8.0 | 32.0 | 0.7 | 2.5 |
PARTH 50 SW-R | 15.0 | 50.0 | 0.8 | 3.5 |
PARTH 63 SW-R | 20.0 | 63.5 | 1.0 | 4.5 |
Tube mills for Various grades of stainless Steel | ||||||||||
Over 150 installation in lndia and abroad | ||||||||||
| ||||||||||
Cross key ways for permanent alignment of forming & sizing stands on the base frames | ||||||||||
Shafts from alloy steel, duly heat treated, ground, hard-chrome plated & ground again | ||||||||||
Idler Roll stand assembly designed for vertical height adjustment while the mill is in operation | ||||||||||
Screw down movement of Turk's head rolls by link-pin mechanism for ease in reforming thick walled sections | ||||||||||
W-forming system in Roll design for better edge-forming & freedom from wrinkle while forming sizes with adverse t/D ratio | ||||||||||
Bead Rolling System with hydraulic operation for continuous rolling of inside bead of welding operation. | ||||||||||
Duly heat treated & ground Rolls from High Carbon High Chromium (HCHC), finished on CNC profile cutting machine |
Model Name | Tube Size Range* | Tube Thickness | ||
Min O.D. | Max O.D. | Min. | Max. | |
PARTH 10 TM | 3 | 10 | 0.25 | 0.6 |
PARTH 15 TM | 6 | 16 | 0.3 | 1.0 |
PARTH 25 TM | 6 | 25 | 0.4 | 1.6 |
PARTH 40 TM-S | 9 | 27 | 0.4 | 3.0 |
PARTH 40 TM | 9 | 38 | 0.5 | 2.5 |
PARTH 40 TM-E | 9 | 51 | 0.6 | 2.0 |
PARTH 50 TM | 12 | 51 | 0.6 | 3.0 |
PARTH 50 TM-E | 12 | 65 | 0.6 | 2.5 |
PARTH 65 TM | 15 | 65 | 0.8 | 3.6 |
PARTH 65 TM-E | 15 | 76 | 0.8 | 3.0 |
PARTH 90 TM-S | 20 | 76 | 1.0 | 4.5 |
PARTH 90 TM | 20 | 90 | 1.0 | 4.0 |
PARTH 115 TM-S | 25 | 90 | 1.2 | 5.0 |
PARTH 115 TM | 25 | 115 | 1.2 | 4.5 |
PARTH 140 TM-S | 32 | 115 | 1.6 | 6.0 |
PARTH 140 TM | 32 | 141 | 1.6 | 5.4 |
PARTH 170 TM | 50 | 168 | 2.0 | 6.0 |
PARTH 220 TM | 60 | 219 | 2.5 | 7.0 |
PARTH 270 TM | 75 | 273 | 2.8 | 8.0 |
Coil Slitting Line suitable for ferrous & non ferrous metals such as Mild Steel, Carbon Steel, Stainless Steel, Aluminum, Brass, Copper etc | ||||||||||
Custom made designs as per requirement | ||||||||||
| ||||||||||
Push-Pull mode for precision slitting | ||||||||||
Pull through mode for heavier gauges | ||||||||||
Coil weight up to 30 MT | ||||||||||
Coil Width up to 2000 mm | ||||||||||
Strip thickness up to 8 mm. | ||||||||||
Duly heat treated &ground slitting cutters & spacers | ||||||||||
Rubber lined spacers for smoother edges by reducing tear area of the slitted strips |