Our Products
Gearboxes
1 Products availableTransformers
1 Products availableWe offer the best product range of Three Connection FIG Pump, Rotary Gear Pump, SS Rotary Gear Pump, rotary twin gear pumps and Three Screw Pump.
Pump In Cast Iron Construction
Model | Suc. X Del. in Inches |
Capacity | Recommended Motor hp at Diffrential Pressur of 'X' kg/cm2 at 325 CST Viscosity |
Weight of Bare Pump Kg | ||||||||||
Ipm | m3 / hr | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | |||
PRG - 050 | ½ Χ ½ | 20 | 1.2 | 0.5 | 0.75 | 2.3 | ||||||||
PRG - 075 | ¾ Χ ¾ | 30 | 1.8 | 0.5 | 0.75 | 1 | 4.5 | |||||||
PRG - 100 | 1" Χ 1" | 50 | 3 | 0.5 | 0.75 | 1 | 1.5 | 6.2 | ||||||
PRG - 125 | 1 ¼ Χ 1 ¼ | 75 | 4.5 | 1 | 1.5 | 2 | 3 | 8.5 | ||||||
PRG - 150 | 1 ½ Χ 1 ½ | 110 | 6.6 | 1.5 | 2 | 3 | 5 | 10 | ||||||
PRG - 200 | 2" Χ 2" | 225 | 13.5 | 3 | 5 | 7.5 | 18 | |||||||
PRG - 250 | 2 ½ Χ 2 ½ | 350 | 21 | 5 | 7.5 | 10 | 12.5 | 27.3 | ||||||
PRG - 300 | 3" Χ 3" | 500 | 30 | 10 | 12.5 | 15 | 20 | 38.5 |
Applications :
The suction and delivery connection are available in 1/4 to 2 ½” size. These Gear Pumps can be operated up to pressure of 10 kg/cm² with 8.33 LPM to 300 LPM flow capacity and has suction lift of 1m to 5m at rated speed of 1440 RPM. These pumps are designed up to maximum Viscosity of 1, 00, 000 SSU and maximum temperature up to 200ºc
Technical Features :
INTERNAL POWER LOSSES
The internal power losses in rotary pumps are of two types the mechanical losses is the power necessary to overcome frictional drag of all the moving part withing the pump while viscous losses id power required to overcome liquid viscous drag & shearing action of the fluid. this can be computed from the graph on the opposite sideH.P CALCULATION
The break horse power required to drive a rotary pump is sum of the theoretical hp & internal losses. the theoretical horse power is the actual work done is moving the fluid from inlet port to out let pressure condition & is product of constant C=0.037, Capacity in cub. Mt/hr. & pressure Kg/Sq. Cm or constant C=2.39, Capacity is us G.P.M. & Pressure in PSIPUMP SELECTION & USES
The bush bearing type of pump can be used for clean viscous liquid having sufficient lubricating Value such as clean lube oil vegetable oil, Fish & Animal oil, Gear oil, Glycerine, Hydraulic oil for intermittent duty. However for continues duty pump with needle roller bearing in SI Series should be selected for liquid having low viscosity poor lubricating values of containing dirts or impurities Such as asphalt bitumen Furnace oil tar, Cellulose, Starch LSHS, HPS, Molasses Napthia, Phenol resin, RFO, Silicate Soap Solution Viscous wax etc.INSPECTION AND TESTING
All pumps are individually tested for its performance as per JIS B- 8312- 1976
Available Model Size & Capacity
Size & Model | 1440 RPM CAPACITY | PUMP GD2 IN KGM2 | ELE MOTOR H.P | FR.SIZE | ||
LPM | US GPM | M3/HR | ||||
½" 50 P-M-L | 06.30 / 16.60 / 25.00 | 02.20 / 04.40 / 06.60 | 0.50 / 1.00 / 1.50 | 0.0008 / 0.0009 / 0.0010 | 0.50 / 0.75 / 1.00 | 71M / 80M / 80M |
1" 100 P-M-L | 33.30 / 50.00 / 60.00 | 08.80 / 13.20 / 15.94 | 2.00 / 3.00 / 3.60 | 0.0007 / 0.0008 / 0.0009 | 0.75 / 1.00 / 2.00 | 80M / 80M / 90L |
1.½" 150 P-M-L | 83.30 / 100.00 / 125.00 | 22.00 / 26.40 / 33.30 | 5.00 / 6.00 / 7.60 | 0.0008 / 0.0009 / 0.0032 | 2.00 / 3.00 / 5.00 | 90L / 100L / 112M |
2" 200 P-M-L | 150.00 / 166.00 / 200.00 | 39.00 / 44.00 / 52.80 | 5.00 / 6.00 / 7.60 | 0.0069 / 0.0074 / 0.008 | 3.00 / 5.00 / 7.50 | 100L / 112M / 132S |
2.½" 250 P-M-L | 250.00 / 299.88 / 333.30 | 66.00 / 79.20 / 88.00 | 9.00 / 10.00 / 12.0 | 0.01 / 0.013 / 0.015 | 5.00 / 7.50 / 10.00 | 112M / 132S / 132M |
3" 300 P-M-L | 415.00 / 449.82 / 500.00 | 105.00 / 118.00 / 132.00 | 15.00 / 18.00 / 20.00 | 0.02 / 0.024 / 0.027 | 10.00 / 12.50 / 15.00 | 132M /160M / 160M |
4" 400 P-M-L | 599.76 / 666.66 / 833.30 | 158.40 / 176.00 / 220.00 | 25.00 / 27.00 / 30.00 | 0.056 / 0.062 / 0.072 | 15.00 / 20.00 / 25.00 | 160M / 160L / 180M |
5" 500 P-M-L | 1000.00 / 1250.00 / 1499.00 | 264.00 / 330.00 / 396.00 | 60.00 / 75.00 / 90.00 | 0.098 / 0.112 / 0.177 | 20.00 / 30.00 / 40.00 | 160L / 180L / 200L |
6" 600 P-M-L | 1660.00 / 1832.00 / 2083 .00 | 440.00 / 484.00 / 550.00 | 100.00 / 110.00 / 125.00 | 0.27 / 0.31 / 0.335 | 30.00 / 50.00 / 60.00 | 180L /225S / 225M |
6" 600 P-M-L | 2499.00 / 2915.50 / 3332.00 | 660.00 / 770.00 / 880.00 | 160.00 / 175.00 / 200.00 | 0.4561 / 0.542 / 0.601 | 50.00 / 75.00 / 100.00 | 225S/ 250M / 280S |
Graph Image
Features :
Lubrication, Hydraulic jacking, Firing, Transfer, CirculationTypical Industries
Power generation, Marine, Navy, Oil & Gas, General Industrial, Machine Tool, Steel, Cement, Chemical, Rayon
Application :
Instruction:
General Specification : "PARAS" Fuel Injection Gear Pumps are positive displacement gear pumps. Available with without built in pressure relief valve. Pimps are of High Pressure and Internal Lunrication system is so design ed that the liquid running through the pump acts as a lubricant. Pumps are designed for wide range of applications. They should not be used for handling abrasive liquids with solid matter. Pumps are self priming and give maximum vaccum of 610-660 mm of Hg. They can handle non-corrosive and non abrasive liquids of maximum vicosity of 455 cents-stocks(CS) and temperature 200 degree celcius.
Salient Features :
Technical Specification
Model | Inlet & Outlet Size | Capacity Iph | Speed rpm | Recommended Motor hp at | ||
5 kg/cm2 | 15 kg/cm2 | 30 kg/cm2 | ||||
PIG-50 | ½ Χ ½ | 150 | 1440 | 0.25 HP | 0.75 HP | 1.5 HP |
300 | 0.25 HP | 0.75 HP | 1.5 HP | |||
450 | 0.5 HP | 1 HP | 1.5 HP | |||
600 | 0.5 HP | 1 HP | 2 HP | |||
PIG-75 | ¾ Χ ¾ | 1000 | 0.75 HP | 2 HP | 3 HP | |
1500 | 0.75 HP | 2 HP | 3 HP | |||
2000 | 1 HP | 3 HP | 5 HP | |||
2500 | 1 HP | 3 HP | 5 HP |