GST : 03AAHCP3513H1ZS
Verified
Write a Review
Our Products
Emulsifiers
1 Products availableCatalysts And Absorbents
1 Products available
PTSC CREPE 6188 is an oil based crepe release aid containing a blend of oils, esters and nonionic surfactants that makes this product easily emulsify in water. PTSCCREPE 6188 is specifically formulated as an effective crepe release in the manufacturing of tissue and towel products. It is compatible with all commercial crepe adhesives, to provide the proper balance for effective creping.
Features:
Guidelines for use
PTSCCREPE 6188 is applied through the spray boom onto the Yankee dryer surface. Our representative will recommend the optimum dosage rates and delivery system required for your process.
Handling and Compatability
Diaphragm pump with Teflon diaphragm, PVC, 316 SS drum transfer or air diaphragm pumps are recommended for feeding. Refer to Safety Data Sheet containing detailed information relative to this product before handling.
Regulatory Information
PTSC CREPE6188 is manufactured in compliance with the regulations of 21 FDA 176.170 and 176.180.
Packaging and Storage
PTSC CREPE 6188 is available in 210-litre capacity drum and 1, 000-litre capacity tote bin. PTSC CREPE 6188 should be stored at 10 - 40 ° C .Recommended shelf life is 12 months from the date of manufacturing.
PTSC WSR 3632 Wet Strength Resin PTSC WSR 3632 is a cationic polyamide wet strength resin supplied as an aqueous solution containing Approximate 12.5% solids. When applied under acidic or alkaline stock conditions, PTSC WSR 3632 will efficiently increase the wet strength properties of finished paper or paperboard products. Use and Application PTSC WSR 3632 resin is highly effective for developing wet strength in facial tissue, napkins, towels, carrier board, liquid packaging, bag paper, linerboard, medium, and other Speciality papers. PTSC WSR 3632 performs over a broad pH range of 4.0 – 9.0 (with best efficiency between 6.5 – 8.0) in the presence of normal papermaking additives. Typical furnish levels range from 0.2 to 0.75% (dry basis), which is dependent upon the wet strength level desired and the grade being manufactured. PTSC WSR 3632 can be added to either the thin or thick stock systems. Best results are achieved with sufficient random dilution and maximum available stock agitation at the point of addition. PTSC WSR 3632 should be added after rosin size and alum addition
The wet strength is not fully developed by the time a paper product reaches the end of a paper machine, and strength continues to develop as the paper is stored. The rate of curing is affected by the temperature and the length of time in contact with heat. The bonds that are eventually formed are not readily broken under either acid or slightly alkaline conditions, and the wet strength is therefore permanent. Whilst this can be an advantage in certain applications, it does make the paper or paperboard more difficult to disintegrate. However, the difficulties for the disintegration of WSR -treated paper have not been reported practically when the dosage level of WSR resin is below 4%.
Benefits
Safety
According to the experience we have gained over many years and other information they do not exert any harmful effect on health, provided they are used properly. For details go through the safety data sheet
Handling & Storage
Should be stored in original packaging in cool and dry place, away from sources of heat, flame and direct sunlight, this product will be stable for at least 24 months.
Standard Package
PTSC WSR 3632 is delivered in 225 kg HDPE drum. other packing sizes on request
FIXING AID (P FIX)
Application
P-FIX is recommended to use after dilution with fresh water in any concentration preferably 50-300 GPL in thick stock of pulp. The best point of addition is thick stock line which leads to Fan pump or suction of machine chest pump.
Solution Preparation
Water is to be added into the chemical, Not Vise-Versa
P-FIX is a copolymer of epichlorohydrin and alkylamine which extends high cationicity to the fiber to neutralize its anionicity to reduce its potential difference with respect to the ionic charge of AKD molecule, in order to fix the AKD molecule to the fiber being used in paper production.
COPOLYMER OF EPICHLOROHYDRIN AND ALKYLAMINE
Material Safety Data Sheet
This chemical is declared in "NON-HAZARDOUS" category
Chemical Handling Instruction
Action in case of contact with Chemical
Fire-Fighting Measures
Ecological Information
Effects in sewage treatment plants (bacteria toxicity: respiration / reproduction inhibition) according to present experience, no adverse effects on water purification plants.
Application
P MICRO-P is recommended to be used after preparing the solution in range of maximum upto 5 GPL concentrations and the final concentration at the point of addition should be 0.5 GPL. The best point of addition is in thin stock after the pressure screen and after the point of addition of retention aid.
Solution Preparation
To prepare a ready to use polymer solution it is recommended to use suitable make-down equipment which provides a homogenous and lump free solution and a minimum holding time of 60 minutes prior to application. In-line filtration of the polymer solution is recommended.
P-MICRO-P is an anionic copolymer of acrylamide/ sodium acrylate to enhance drainage phenomenon without affecting the formation of paper and board.
COPOLYMER OF ACRYLAMIDE / SODIUM ACRYLATE
Material Safety Data Sheet
This chemical is declared in "NON-HAZARDOUS" category
Chemical Handling Instruction
Action in case of contact with Chemical
Ecological Information
Our firm is offering Dry Strength Resin to our highly valued clients. It is most suitable product for short fiber pulp like Bagasse, Straw, Waste paper, Bamboo, hard wood etc. It also improves strength properties like burst factor, stiffness, breaking length, ply bonding, tear factor of Kraft, Duplex board and writing and printing paper also increases machine run ability. It improves retention of fillers and eliminates press picking problem of paper.
Additional Information:
Packaging Details : HDPE Drums (200 Kg)
Application
P-FLOC is recommended to be used after preparing the solution in a range maximum up to 5 GPL concentrations and the final concentration at the point of addition should be 0.5 GPL. The best point of addition is in thin stock either before or after the pressure screen depending upon the machine response.
Solution Preparation
To prepare a ready to use polymer solution it is recommended to use suitable make-down equipment which provides a homogenous and lump free solution and a minimum holding time of 60 minutes prior to application. In-line filtration of the polymer solution is recommended.
P-FLOC is a cationic polyacrylamide powder to serve the purpose of retention of fines and fillers in paper & board production.
COPOLYMER OF ACRYLAMIDE/ETHANAMINIUM N, N, NTRIMETHYL- 2-(1-OXO-2-PROPENYL) OXY CHLORIDE.
Material Safety Data Sheet
This chemical is declared in "NON-HAZARDOUS" category
Chemical Handling Instruction
Action in case of contact with Chemical
Ecological Information
Mr. Parth Aggarwal (Papertex Speciality Chemicals Pvt. Ltd.)
1st Floor, 4 Kashmir Plaza, Batala Road, Amritsar, Punjab - 143001, India
Share us via
