The gas detection controller GMA200continues with the tradition of the company under consideration of innovative technology and trend-setting flexibility. It is designed for commercial and industrial applications for the measurement of combustible and toxic gases as well as for the measurement of oxygen. The compact construction of the GMA200-MW4provides a cost-efficient solution for safe gas monitoring of industrial facilities.Parallel Measurement and flexible applicationUp to four analog and 16 digital transmitters can be connected to GMA200-MW4 and monitored simultaneously.Via the configuration software the measurement range, the measurement designation, the type of transmitter and the type of gas can be set individually as well as three alarm thresholds can be programmed for every connected single transmitter.The microprocessor of the GMA200-MW4 evaluates all receiving signals and activates alarm and relays. In doing so one single gas detection controller GMA200-MW4 can master different gas detection tasks.Integrated RelaysPermanent increasing demands on safety measures require complex gas detection systems and redundant protective measures to protect from gas hazards.Therefore the GMA200-MW4 has six internal relays. For the implementation of safety measures and alarm, four relays can be programmed freely so that in case of alarm the safety measures can be triggered automatically. The programming grants wide-ranged and flexible possibilities like allocation of one or more measurement point s to relay, single alarm per measurement point, configuration of collective alarm and group alarm, error report and voting function. For each, safety related error report and maintenance, one further relay is available.Graphic displayThe clear conception of the controllerGMA200-MW4 allows the rapid recognition of hazardous situations. Current measurement values are shown continuous on the LCD- graphic display.At Alarm a red back light is active.Technical dataMeasuring gases: combustible and toxic gases and vapours, for all GfG transmittersDisplay and control elements: 2, 2"-LCD graphic display; 5 button keyboard (left, right, up, down, OK); 13 LEDs for Alarms, operation and Relay statusEnvironmental conditions: for storage:-25.+60C 0.99%r.F. (recommended 0.+30C)for operation: -20.+55C 0.99%r.F.Power supply:Operating voltage: 100-240V AC 50-60Hz or/and 24V DC (20-30V DC valid)Power consumption: max.7W (without Transmitter) max.25W (with Transmitter)Fuse: F1=T 500mA (for GMA200-MW4) F2=M 1A (for Transmitter)Transmitter connection:Power supply: 24V DC 3% with built in power supplyunit, otherwise 20-30VDC (see above) 4x 150mA respectively Itotal=0, 6A atany other subdivisionRS485 outputs:TRM-Bus1+2: RS485; Half-Duplex; max. 38400 Baud (only for GMA200-MW4 relay modules)GMA-Bus: RS485; Half-Duplex; galvanically isolated; max. 230400 Baud (for GMA200-MW4 relays modules, control center, PC, SPS or Gateway)Relay Outputs:Contactors: Six Relays with one open contact eachContact current capacity:3A/250V AC or 3A/30V DCAnalog outputs: 2 x analog output4-20mA (burden max.560)free allocatableAlarm acknowledgement inputs: 2 x Reset, free allocatableData logger (optional): 2GB microSD memory card with FAT (FAT16) formattingUSB terminal: Mini USB jack for configuration of the device via PCConnection cable:Cable entries: max. 9 units M16x1, 5 (for cable cross section 4, 5-10mm)Housing:Protection: IP65Material: PlasticsWeight: ca. 890gDimensions: 209 x 180 x 64mm (W x H x D)Approvals/Testings:Electromagnetic compability: DIN EN 50270:2006Electrical Safety: DIN EN 61010:2010
Additional Information:
- Item Code:GMA200
- Pay Mode Terms:T/T (Bank Transfer), Other
- Port of Dispatch:Mumbai
- Packaging Details:One Sensor Per Box