Bade Ispat And Metal Pvt Ltd

Kalbadevi, Mumbai, Maharashtra

Details :

• Lap Joint Flanges have all the same common dimensions as any other flange named on this page however it does not have a raised face, they used in conjunction with a “Lap Joint Stub End”.
• These flanges are nearly identical to a Slip On flange with the exception of a radius at the intersection of the flange face and the bore to accommodate the flanged portion of the Stub End.
• Their pressure-holding ability is little, if any, better than that of Slip On flanges and the fatigue life for the assembly is only one tenth that of Welding Neck flanges.
• They may be used at all pressures and are available in a full size range. These flanges slip over the pipe, and are not welded or otherwise fastened to it. Bolting pressure is transmitted to the gasket by the pressure of the flange against the back of the pipe lap (Stub End).

Lap Joint flanges have certain special advantages :

• Freedom to swivel around the pipe facilitates the lining up of opposing flange bolt holes.
• Lack of contact with the fluid in the pipe often permits the use of inexpensive carbon steel flanges with corrosion resistant pipe.
• In systems which erode or corrode quickly, the flanges may be salvaged for re-use.

Carbon Steel/ Stainless Steel Lap Joint Flange Pressure :

• ANSI/ASME B16.5 Lap Joint Flange 150lb
• ANSI/ASME B16.5 Lap Joint Flange 300lb
• ANSI-ASME B16.5 Lap Joint Flange 400lb
• ANSI/ASME B16.5 Lap Joint Flange 600lb
• ANSI/ASME B16.5 Lap Joint Flange 900lb
• ANSI/ASME B16.5 Lap Joint Flange 1500lb
• ANSI/ASME B16.5 Lap Joint Flange 2500lb

Carbon Steel Slip On Flanges/ SORF Flanges : ASTM A105/A105N, A350 LF1, LF2 CL1/CL2, LF3 CL1/CL2, A694 F42, F46, F48, F50, F52, F56, F60, F65, F70, A516.60, 65, 70 (Spectacle Blind Flange, Spacer Ring/Spade Flange), Steel RST37.2, C22.8

Carbon Steel/ Stainless Steel Slip On Flanges Pressure :

• ANSI/ASME B16.5 Slip On Flanges 150lb
• ANSI/ASME B16.5 Slip On Flanges 300lb
• ANSI-ASME B16.5 Threaded Flange, Screwed Flange 400lb
• ANSI/ASME B16.5 Slip On Flanges 600lb
• ANSI/ASME B16.5 Slip On Flanges 900lb
• ANSI/ASME B16.5 Slip On Flanges 1500lb
• ANSI/ASME B16.5 Slip On Flanges 2500lb

Carbon Steel/ Stainless Steel Blind Flange Pressure :

• ANSI/ASME B16.5 Blind Flange 150lb
• ANSI/ASME B16.5 Blind Flange 300lb
• ANSI/ASME B16.5 Blind Flange 400lb
• ANSI/ASME B16.5 Blind Flange 600lb
• ANSI/ASME B16.5 Blind Flange 900lb
• ANSI/ASME B16.5 Blind Flange 1500lb
• ANSI/ASME B16.5 Blind Flange 2500lb
• ANSI/ASME B16.47 Series B Blind Flange 75lb
• ANSI/ASME B16.47 Series B Blind Flange 150lb
• ANSI/ASME B16.47 Series B Blind Flange 300lb
• ANSI/ASME B16.47 Series B Blind Flange 400lb
• ANSI/ASME B16.47 Series B Blind Flange 600lb
• ANSI/ASME B16.47 Series B Blind Flange 900lb
• ANSI/ASME B16.47 Series A (MSS SP44) Blind Flange 150lb
• ANSI/ASME B16.47 Series A (MSS SP44) Blind Flange 300lb
• ANSI/ASME B16.47 Series A (MSS SP44) Blind Flange 400lb
• ANSI/ASME B16.47 Series A (MSS SP44) Blind Flange 600lb
• ANSI/ASME B16.47 Series A (MSS SP44) Blind Flange 900lb

Carbon Steel/ Stainless Steel Plate Flange Pressure :

• ANSI/ASME B16.5 Plate Flange 150lb
• ANSI/ASME B16.5 Plate Flange 300lb
• ANSI-ASME B16.5 Plate Flange 400lb
• ANSI/ASME B16.5 Plate Flange 600lb
• ANSI/ASME B16.5 Plate Flange 900lb
• ANSI/ASME B16.5 Plate Flange 1500lb
• ANSI/ASME B16.5 Plate Flange 2500lb

Details :

• Forged flange the conventional flange products. It is invented on the basis of the cast flange into production, its intensity to be higher than the cast steel flange many interconnected so that the tube with the tube parts, is connected to the tube end.
• Hammered holes in the flange bolt flange abuts. Forged flange gasket sealing. Forged flange fittings (flanged pipe fittings) fittings with forged flange (flange or disk access). It can be cast from (Figure N), can also be threaded connections, or welding. Flanged connections (flange, joint) by a pair of flange, a gasket and a number of bolts and nuts. Gasket on the between two flange sealing surface, tighten the nut, than on the gasket surface deformation pressure reaches a certain value, and fill the sealing surface asperities join not leak tight.

Carbon Steel/ Stainless Steel Forged Flange Pressure :

• ANSI/ASME B16.5 Forged Flange 150lb
• ANSI/ASME B16.5 Forged Flange 300lb
• ANSI-ASME B16.5 Forged Flange 400lb
• ANSI/ASME B16.5 Forged Flange 600lb
• ANSI/ASME B16.5 Forged Flange 900lb
• ANSI/ASME B16.5 Forged Flange 1500lb
• ANSI/ASME B16.5 Forged Flange 2500lb

Socket weld flange is similar to the slip-on flange in outline, but the bore is counter-bored to accept pipe. Socket welding pipe flanges are typically used on smaller sizes of high pressure pipes. Socket weld flanges are widely used in high pressure systems such as hydraulic equipment and steam lines. Socket weld pipe flanges are attached by inserting the pipe into the socket end and then applying fillet weld around the hub of the flange. This allows for a smooth bore and better flow of the fluid or gas inside of the pipe. An optional internal weld may be applied in high stress applications.

Carbon Steel Socket Weld Flange/ SW Forged Flanges : ASTM A105/A105N, A350 LF1, LF2 CL1/CL2, LF3 CL1/CL2, A694 F42, F46, F48, F50, F52, F56, F60, F65, F70, A516.60, 65, 70 (Spectacle Blind Flange, Spacer Ring/Spade Flange), Steel RST37.2, C22.8

Carbon Steel/ Stainless Steel Socket Weld Flange Pressure :

• ANSI/ASME B16.5 Socket Weld Flange 150lb
• ANSI/ASME B16.5 Socket Weld Flange 300lb
• ANSI-ASME B16.5 Threaded Flange, Screwed Flange 400lb
• ANSI/ASME B16.5 Socket Weld Flange 600lb
• ANSI/ASME B16.5 Socket Weld Flange 900lb
• ANSI/ASME B16.5 Socket Weld Flange 1500lb
• ANSI/ASME B16.5 Socket Weld Flange 2500lb

Carbon Steel Threaded/ Screwed Flanges : ASTM A105/A105N, A350 LF1, LF2 CL1/CL2, LF3 CL1/CL2, A694 F42, F46, F48, F50, F52, F56, F60, F65, F70, A516.60, 65, 70 (Spectacle Blind Flange, Spacer Ring/Spade Flange), Steel RST37.2, C22.8

Carbon Steel/ Stainless Steel Threaded Flanges Pressure :

• ANSI/ASME B16.5 Threaded Flange/Screwed Flange 150lb
• ANSI/ASME B16.5 Threaded Flange/Screwed Flange 300lb
• ANSI-ASME B16.5 Threaded Flange, Screwed Flange 400lb
• ANSI/ASME B16.5 Threaded Flange/Screwed Flange 600lb
• ANSI/ASME B16.5 Threaded Flange/Screwed Flange 900lb
• ANSI/ASME B16.5 Threaded Flange/Screwed Flange 1500lb
• ANSI/ASME B16.5 Threaded Flange/Screwed Flange 2500lb

Details :

• We offer threaded pipe flanges manufactured at our facility to companies in various industries including shipbuilding, power generation, petrochemical plants, oil refineries, waste water treatment plants, paper mills, pharmaceutical plants and turnkey projects among others.
• Our products are widely exported to countries and regions such as the United States, Europe, Russia, Turkey, Malaysia, the UAE, Saudi Arabia, Iran, Brazil, Chile, Mexico, South Africa, Jordan, Tunisia, Vietnam, Indonesia, Thailand, Singapore, Colombia, and Sri Lanka.

Carbon Steel WNRF Flange/ Weld Neck Flange : ASTM A105/A105N, A350 LF1, LF2 CL1/CL2, LF3 CL1/CL2, A694 F42, F46, F48, F50, F52, F56, F60, F65, F70, A516.60, 65, 70 (Spectacle Blind Flange, Spacer Ring/Spade Flange), Steel RST37.2, C22.8

Carbon Steel/ Stainless Steel Weld Neck Flange Pressure :

• ANSI/ASME B16.5 WNRF Flange/ Weld Neck Flange 150lb
• ANSI/ASME B16.5 WNRF Flange/ Weld Neck Flange 300lb
• ANSI-ASME B16.5 WNRF Flange/ Weld Neck Flange 400lb
• ANSI/ASME B16.5 WNRF Flange/ Weld Neck Flange 600lb
• ANSI/ASME B16.5 WNRF Flange/ Weld Neck Flange 900lb
• ANSI/ASME B16.5 WNRF Flange/ Weld Neck Flange 1500lb
• ANSI/ASME B16.5 WNRF Flange/ Weld Neck Flange 2500lb