Neo Pack Plast Pvt. Ltd

Vapi, Gujarat

Description:

NEOSHIELD PU Paints are 2 part polyurethane based top coat offering good resistance to chemical, UV. These products are designed to offer best gloss retention. The product has got excellent adhesion strength and also offers a balanced aesthetic and corrosion protection. NEOSHIELD PU Paints are available in Clear / High Glossy / Semi Glossy varieties. Special products with non yellowing fetaures are also available. These products cure at Room temperature and provides excellent flexibility, toughness, good abrasion, chemical & UV resistance.

Surface Preparation:

Abrasive blasting to Sa 2 Swedish standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3. The surface should be absolutely dry, moisture and oil free before primer application. And for Application on Primer scuff with 100 no types emery paper for proper bonding and performance.

Application Method:

Stir the Base part thoroughly. Mix base and Hardener as per our recommended ratio, by volume, Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add suggested Thinner into mix, if required, depending on application method, and stir gently for few minutes. Stain the paint through nylon filter cloth of 300 mesh size and apply uniformly over the surface. All equipment used for above should be properly cleaned. Apply By Brush/By Conventional spray.

Neo Bituminous products segment has full fledged range meeting different customer requirements. Neo has individual products for following uses a) Water Tank Coating b) Anti Corrosive Coating IS 158, c) Fast Drying Bituminous varnish, d) Special purpose Bitumionous primers that are useful for waterproofing products. They are all specially designed solvent based, products formulated with high quality bitumen, petroleum solvent & selective additives. It is resistant to acid, alkali and water. The product dries rapidly to give a smooth glossy black finish. The product imparts good adhesion strength on coated surfaces. The product performs as a anticorrosive brushable liquid primer cum paint as well as a good blending agent for the manufacture of waterproof membrane coating.

NEOPOXY RESIN & HARDENER systems are specially formulated product based on epoxy resins and amine based hardener. This product react by cross linking to form cured hard mass at room temperature. RESIN & HARDENER are to be mixed as per ratio suggested in data sheet and application to be completed within the pot life of the mixed product.

This is a single pack Polymer modified Cementitious System based Tile Adhesive. The product offers excellent resistance to complete immersion & adhesion to all building material. Curing is not required for Permanent tile fixing. Ideally suitable for ceramic, mosaic tile bonding. Coverage : 13-14 kg/m2 when applied by 7 mm notched trowel.

This is a thixotropic solvent free, epoxy resin based hard wearing & attractive tile joint grout. The system has low odour & is resistant to water, weathering & wide range of industrial chemicals. The product comes with unique colour pack system to match tiling colours. Apply the mixed component (Resin + Hardener + Filler) with a spatula into the spaces between the tiles & around the edges. Remove excess material with a dry cloth. Finds extensive use for bathrooms/ swimming pools/ factories/ hospital where a stain free easily cleanable product is required. Coverage : 0.25 kg /m2.

Acrylic Wall Putty is a water based ready-to-use putty. It is designed to give the best properties as an under coat, provides a very strong, durable foundation and brings out the best of finish paints in looks and durability. AWP is a perfect product meant for filling and smoothening out cracks and dents on the plastered wall or similar interior surfaces. A very finely mixed and quick drying putty with superior acrylic binders, AWP not only gives a firm grip on the wall surface but makes painting over it extra rich. Over and above the putty surface has limited porosity and good breathability as against conventional putties. It also exhibits good alkali resistance.

NEOPROOF FILCRAK is a single pack, ready to use flexible non sag paste specially designed for filling the cracks in plastered surfaces. Composed of high quality durable acrylic polymer, finely graded fillers, light fast pigment & additives, it offers excellent bonding to Cementitious surfaces, water & UV resistance, aesthetic non staining appearance & durability. Conforming to ASTM C 834 91 it is suitable for use in internal & external plastered brick masonry wall cracks of upto 5mm width. Being flexible accommodates minor movements in cracks. It is non toxic, environmental friendly product. Application is done with a spatula / knife. Its better to apply bond coat of the product with 1:1 water diluted mix. Allow to dry for 24 hours and then proceed with sequential activities. Limitations -Should not be used for cracks more than 5 mm thick. Not to be used in cracks of structural members, expansion joints & separation gaps.

NEOs RUST-O-KILL is a single part adduct of polar solvents & organic acids specially formulated to remove rust, convert rust into non corrosive coating & also act as an active oil & de-greasing agent. Its 3 in 1 action of RUST REMOVAL/RUST CONVERSION/DEGREASING offers a handy product for all maintenance needs. Finds use in all industries/building & construction etc. Dilution is possible with water but for badly rusted areas undiluted usage is preferable. Apply with brush or dry cloth/sponge or spray gun on surfaces which are rusted or where initial rusting has started & requires re-painting. Wait for 5 to 10 mins & then scrub clean the surface with Sand or Emery paper. Remove loose particles & wipe with wet cloth & then with dry cloth. Apply primer or paint as required immediately.

NEO PRIME GUARD RED OXIDE PRIMERS are specially developed 2 part epoxy based anti corrosive product containing Zn Phosphate added with superior corrosion inhibiting pigments. The product is phenalkamine curing red oxide primer. Recommended as primer on MS Surface for OEMs, process industries like fertilizers, refineries, chemical & other plants. Also useful in diverse areas of tank exteriors, equipments, pipelines, structural steel, etc. Not to be used for immersion application. The product gives Red Oxide Matt Finish whose surface dry will be in 1530 mins & hard dry in 12 hrs. Coverage is approx 10-11 sq m / ltr for 35 micron DFT. Mix base and hardener as per ratio advised. Pot life of mixed content is 2 hrs & the coating is compatible to all types of top coats. Neo has in its range RED OXIDE PRIMERS made with different base other than epoxy.