Navkar Engineering

Udhna, Surat, Gujarat

The B series balancers come standard with NO CONTROLS, and are designed for integration with an end effector or handling device that includes a control package.

• If the air supply is ever interrupted, the unit will maintain the load in the suspended position
• If the load is accidentally lost, a spring loaded centrifugal brake automatically stops the rapid upward cable travel
• The load being lifted can never exceed the units maximum rated capacity at a given air pressure
• Eliminates the down-drift of suspended loads within 6 inches (152 mm) if air supply is shut down
• Length of wire rope up to 30 ft (9.1 m) with cable travel up to 120 inches (3048 mm) depending on model and configuration
• Suspension kits are available for virtually all enclosed track manufacturers, as well as I-beam, Patented/Hardened track, and Hook mounted configurations

The operator experiences virtually no part weight or resistance in manipulating the load. The BA; controller is a self-relieving regulator that automatically adds or exhausts air to raise or lower (float) the load to the desired height where it will remain suspended. The regulator can also be adjusted to slowly raise a load up and out of an operators way. The primary application for the BA series balancer is for suspending and/or positioning constant weight items.

• Standard Z-Servo control (BA balancers over 200 lb (90.7 kg)) amplifies the inputs and reduces the effort required to lift the load
• If the air supply is ever interrupted, the unit will maintain the load in the suspended position
• If the load is accidentally lost, a spring loaded centrifugal brake automatically stops the rapid upward cable travel
• The load being lifted can never exceed the units maximum rated capacity at a given air pressure
• Eliminates the down-drift of suspended loads within 6 inches (152 mm) if air supply is shut down
• Length of wire rope up to 30 ft (9.1 m) with cable travel up to 120 inches (3048 mm) depending on model and configuration
• Suspension kits are available for virtually all enclosed track manufacturers, as well as I-beam, Patented/Hardened track, and Hook mounted configurations

When the pendant is in the LO- and UN-LOAD position, balancer air pressure is released to allow the lighter loads to be in balance. When the pendant is in the HI-LOAD position, no pressure is released, and the heaviest load can be balanced. The EA series balancers are ideally suited for applications where up to 3 load sizes are frequently lifted, and operator hands-on the part is required. The UN-LOAD position is also often used for handling device balancing (loaded/unloaded).

• Rotary thumb switch pendant selects HI-LOAD, LO-LOAD, or NO-LOAD setting
• If the air supply is ever interrupted, the unit will maintain the load in the suspended position
• If the load is accidentally lost, a spring loaded centrifugal brake automatically stops the rapid upward cable travel
• The load being lifted can never exceed the units maximum rated capacity at a given air pressure
• Eliminates the down-drift of suspended loads within 6 inches (152 mm) if air supply is shut down
• Length of wire rope up to 30 ft (9.1 m) with cable travel up to 120 inches (3048 mm) depending on model and configuration
• Suspension kits are available for virtually all enclosed track manufacturers, as well as I-beam, Patented/Hardened track, and Hook mounted configurations

The InteLIFT Basic unit comes with no controls and is designed to be integrated with a Handling Device and operated with the Handling Devices control package.

• Intuitive speed control for a variety of different weights
• Electric controls plus air operation give you continuous duty cycle with minimal maintenance
• Eliminates the potential to accidentally drop a part
• 3 speed selector enables speeds to match each application and operator comfort level
• Lift and lower is the default mode of the InteLIFT unit and allows the operator precision handling of variable weight loads
• Allows the operator to manually raise, lower and position Float a load with virtually no part weight or resistance to the operator
• Is part of the new Intelligence for balancers and allows dumping or pouring of material while maintaining load position and stability
• Allows for the automatic release of a load by a Handling Device once the load is lowered and no longer supported by the InteLIFT

The pendant handle contains a rocker switch for quick up/down load positioning. Float mode is active at the touch of a button.

• Intuitive speed control for a variety of different weights
• Electric controls plus air operation give you continuous duty cycle with minimal maintenance
• Eliminates the potential to accidentally drop a part
• 3 speed selector enables speeds to match each application and operator comfort level
• Lift and lower is the default mode of the InteLIFT unit and allows the operator precision handling of variable weight loads
• Allows the operator to manually raise, lower and position Float a load with virtually no part weight or resistance to the operator
• Is part of the new Intelligence for balancers and allows dumping or pouring of material while maintaining load position and stability
• Allows for the automatic release of a load by a Handling Device once the load is lowered and no longer supported by the InteLIFT

The InteLIFT IC series balancers come standard with a force-sensing load cell that converts small levels of operator force into up/down movement through the full lifting range, without the need for up/down pendant controls. These models also come equipped with a 12 ft (3.7 m) twin-bonded pre-coil cable including air hose and electronic control hose.

• Intuitive speed control for a variety of different weights
• Electric controls plus air operation give you continuous duty cycle with minimal maintenance
• Eliminates the potential to accidentally drop a part
• 3 speed selector enables speeds to match each application and operator comfort level
• Senses force input of the user and translates it to assisted lifting and lowering of the load without the need for pushing additional up/down buttons.
• Lift and lower is the default mode of the InteLIFT unit and allows the operator precision handling of variable weight loads
• Is part of the new Intelligence for balancers and allows dumping or pouring of material while maintaining load position and stability
• Allows for the automatic release of a load by a Handling Device once the load is lowered and no longer supported by the InteLIFT
• Allows the operator to manually raise, lower and position Float a load with virtually no part weight or resistance to the operator

A pendant handle that contains a rocker switch for quick up/down load positioning. Float mode is active at the touch of a button.

• Intuitive speed control for a variety of different weights
• Electric controls plus air operation give you continuous duty cycle with minimal maintenance
• Eliminates the potential to accidentally drop a part
• 3 speed selector enables speeds to match each application and operator comfort level
• Lift and lower is the default mode of the InteLIFT unit and allows the operator precision handling of variable weight loads
• Allows the operator to manually raise, lower and position Float a load with virtually no part weight or resistance to the operator
• Is part of the new Intelligence for balancers and allows dumping or pouring of material while maintaining load position and stability
• Allows for the automatic release of a load by a Handling Device once the load is lowered and no longer supported by the InteLIFT

Up/down movement is accomplished through the use of an ergonomically designed pendant with low-effort, color coded thumb levers. After positioning the load with the pendant control, the unit defaults into a Float; mode that allows the operator up to 18 in (457 mm) to manually adjust the load for final positioning.

• Ergonomic Up/Down pendant control for variable speed and feathering of load
• If the air supply is ever interrupted, the unit will maintain the load in the suspended position
• If the load is accidentally lost, a spring loaded centrifugal brake automatically stops the rapid upward cable travel
• The load being lifted can never exceed the units maximum rated capacity at a given air pressure
• Eliminates the down-drift of suspended loads within 6 inches (152 mm) if air supply is shut down
• Length of wire rope up to 30 ft (9.1 mm) with cable travel up to 120 inches (3048 mm) depending on model and configuration
• Suspension kits are available for virtually all enclosed track manufacturers, as well as I-beam, Patented/Hardened track, and Hook mounted configurations

• This 1:1 ratio, one-inch diaphragm pump hasdual inlets(3/4-inch NPTF) to allowsimultaneous pumping and blending of antifreeze and water.

• 66100 Wall mount bracket

• Designed for the purpose of evacuating and filling tires with calcium chloride ballast solution.
• 613201-2-C Calcium Chloride Tire Fill Package: Includes Inlet and outlet hoses, Strainer, Tire Filling 8 Suction hose, Control handle, and Check valve

• Designed for heavy duty cleaning of equipment and washing down parts with detergents, caustics, and dilute acid type cleaners!!
• 10:1 ratio double acting pump section is separated from the air motor to prevent any cleaning solution from coming in contact with and damaging the air motor
• Mounting versatility wall mounted or directly mounted in 2 bung of a standard 55 gal. drum
• Reliable 4-1/4 diameter air motor, 4 stroke, stub mounted