Heating element

• The hot end roughness D1 of the silicon molybdenum rod is 7mm, the average manufacturer adopts 6MM, the heating end is thick, the surface load of the rod is low, and the service life is long.
• It adopts hot bending technology, with uniform resistance and long service life
• The length of the cold end of the Lu is 210mm, 400X300X300 furnace is 260, the general manufacturer adopts 180mm, and the cold end has a low temperature.
• The surface oxidation of silicon molybdenum rod is compact and can better protect the silicon molybdenum rod.

Install air switch and leakage protector:

When an electric current or leakage, an empty meeting automatically disconnects.

Can connect with computer

This furnace is equipped with communication interface and software, can be directly through the furnace computer control of each parameter, and can be observed from the computer PV on the stove and SV temperature value and instrument operation, the actual temperature of the furnace curve drawing computer real time, and can keep the temperature data of each time, can call up at any time.

Chamber

Imported VS Chinese

• High quality high pure alumina polycrystalline fiber cured furnace with vacuum suction and filter molding.
• Adopt Japanese technology to form.
• The spacing and pitch of the resistance wire in the furnace are arranged according to the best thermal technology of Japan, and the temperature field is simulated by thermal software
• Using 4 weeks heating, the temperature is more balanced The furnace can not remove powder, heat insulation, high reflectivity and temperature balance, which is strong against heat and shrinkage

Optional UL certified electrical board (all imported electrical appliances approved by UL)

Trigger VS Soft start limited flow trigger   Most of the manufacturers use the non – limited Xiamen botany trigger

• Phase shift trigger (with soft start and current limiting function)
• Current limiting function: no matter how the heating time is adjusted, the secondary current of our electric furnace after the transformer is limited to 170A, and the equipment is limited. Unlimited-flow triggers, if the heating rate is set wrong or too fast, The current is so large at low temperature that the device can trip or burn.
• Soft start function: the current will gradually increase when starting up, and the impact on the heating element will be small, which will help to prolong the life of the heating element
• Protection function: if the current exceeds the limiting current, the trigger will automatically cut off the trigger function to cut off the current protection furnace.

UL certified transformer

• The transformer cable is pure copper
• Small transformer
• Low temperature of transformer

The stainless steel tank of hydrogen atmosphere furnace is installed in the chamber of a stove or furnace a stainless steel tank, the tank oven door USES silicone O ring seal, in order to reduce O ring seal temperature in the furnace door is equipped with water cooling system, thermocouple, inlet valve, the valve installed on the tank, pressure gauge, etc; This furnace installation with hydrogen detector, burner, the combustion controller, alarm lights, torches, explosion-proof valve, etc., after gas after flow meter by chamber in and out, tail gas from the door of the oven after cooling water system. Can pass, argon, nitrogen, oxygen, hydrogen gases such as carbon monoxide, ammonia decomposition gas, &energy-saving equilibrium temperature field, the surface temperature is low, lifting speed, energy saving, clean furnace temperature is not easy to contaminated, universities, research institutes, industrial and mining enterprises do protect the sintering atmosphere, reducing atmosphere, skim the ideal product.

NST-1400C Atmosphere has many advantages of uniform temperature field, low surface temperature, heating or cooling promptly and so on. it is the ideal atmosphere muffle furnace for atmosphere protection sintering, atmosphere reducing in Industry, Scientific research institutes, Universities, which offer Heating element of Sic and double layer housing, phase-shift trigger, controlled silicon. Operation system is Shimaden 40-segments digital controller imported from Japan. The chamber is made of Polycrystalline alumina fibre. There is wind cooling system between the double walled housing to help the furnace heat or cool promptly. Sealed housing, silicon gel sealed cover, sealed door with silicon gel gasket and water cooling system, gas float through flow meter, then come out from back side, there are many gas inlets and gas outlets on the furnace with burning mouth, which can pre-vacuum and pass H2, Ar, N2, O2, CO, NH3 and so on.

• Temperature controller: Shimaden FP93 40 programmable segments (Shimaden fp93 made in Japan), It can separate into 4, 2, 1 programs, ie. 4×10 segments. FP93 have 6 PID controls, different PID are used for low, middle, high temperature for precise control.Over-temperature and over-current protection, shutdown automatically when thermocouple is broken( it will shut down power when temperature is higher than 1420 or thermocouples is broken, “ON” on the board is off and “OFF” is on)There is Fahrenheit (F) and Celsius (C) for option.With 485 communication interface: which can stop the furnace automatically.
• Cover opening protection system: overtravel-limit switch is installed to protect user, it will cut off power when the cover is opened.
• Chamber:it is imported from Japan,   good performance of heat preservation, high reflectivity, even temperature field, good ability of anti thermal expansion and cold contraction.
• Heating elements:This furnace is installed with Sic to ensure uniform temperature field and long service life.
• Leakage protection function:the furnace is installed with leakage air switch, it will cut off power Automatically when electricity leak or current exceed rated current.
• Software controlling system:this furnace can control every parameter directly and observe PV
• and SV on the computer by communication interface and software, computer can draw and save actual heating curve, it is convenient to call these dates at any time.
• Controlling system: Power control: Chint; Controlled silicon:Germany Semikron 106/16E; Trigger:Phase-shift trigger
• Gas system:floating flow meter or digital flow meter is for option to control gas Speed.
• Vacuum system: Vacuum level can be 10-1 or 10-4 with German molecular pump. TW-1.5 vacuum pump is for option.Pre-vacuuming can help remove air in the chamber quickly.

1400°C 40-Segment Muffle Furnaces w/ PC Interface

NST-1400 Muffle muffle furnaces feature a chamber with Mitsubishi (Japan) high quality alumina fiber insulation and silicon carbide (SiC) heating elements. A double walled steel internal housing helps minimize heat loss to exterior surface.

Furnace operation is controlled by Shimaden (Japan) 40-segment digital controller with built-in RS485 digital communications port and USB adaptor, allowing the user to connect to a PC for remote control and monitoring of the furnace. You can also save or export test results.

Features

• Microprocessor based self-tuning PID control provides optimum thermal process with minimal overshoot.
• Built-in ammeter and dual voltmeters for easy monitoring and troubleshooting.
• Built-in computer interface.
• Long life type S thermocouple.
• CE compliant

Safety

• Overheat protection shuts down the furnace if temperature is outside of acceptable range (refer to controller’s manual) or when the thermocouple is broken or malfunctions.
• Power failure protection resumes furnace operation right after the point of failure when power is reestablished.

NST 1600C High Temperature Microwave Sintering Furnace

High Temperature Up To 1600C Microwave Muffle Furnace

• Microwave heating.
• Temperature up to 1600 degree.
• Heating speed up to 50 degree per minute.
• No pollution to material.

Application Field:

• Claiming / synthesis of powder or particle materials:
• Electronic ceramic powders: barium titanate, barium-strontium titanate, strontium titanate, barium zirconate titanate;
• Lithium ion battery anode materials: lithium cobaltoxide, lithium manganate;
• Various colorants, glaze material, inorganic pastel;
• Alumina, magnesium oxide, zinc oxide, manganese dioxide, manganous-manganicoxide, zirconia, ammonium metavanadate, vanadium pentoxide, titanium dioxide, zinc carbonate, manganese carbonate, aluminum hydroxide, magnesium hydroxide, lithium cobaltoxide, zinc ferrite, Tri-chromatic rare earth fluorescent powder (Red), cement.

Synthesis / sintering of devices:

• Electronic ceramics: Piezoresistive element, thermistor, piezoceramics, microwave medium ceramics;
• Magnetic materials: hard magnetic, Ni-Zn, gyromagnet ferrites;
• Honeycomb ceramics, daily-use ceramics and glass ware;
• Oxide ceramics and refractory materials: alumina, zirconia, magnesium oxide and other oxide composites;
• Incineration, cremation, scaling loss experiments

Protection and Safety: Anode over voltage, anode over current, anode power surpass, electromagnet watchdog, magnetron temperature, external interlock. Control System: PLC (18 sections of temperature control), embedded system connected to laptop via USB, with data storage and printing functions.

NST 1200°C Muffle Furnace w/ Kanthal (Sweden) Heating Elements

NST 1200°C Muffle muffle furnaces feature the famous Kanthal(Sweden) spiral wire coils embedded in Mitsubishi (Japan) high quality alumina fiber insulation. A double walled steel internal housing helps minimize heat loss to exterior surface.

Furnace operation is controlled by Shimaden (Japan) 40-segment digital controller with built-in RS485 digital communications port and USB adaptor, allowing the user to connect to a PC for remote control and monitoring of the furnace. You can also save or export test results.

Features:

• Microprocessor based self-tuning PID control provides optimum thermal process with minimal overshoot.
• Built-in ammeter and dual voltmeters for easy monitoring and troubleshooting.
• Built-in computer interface.
• Long life type K thermocouple.
• CE compliant

Safety

• Overheat protection shuts down the furnace if temperature is outside of acceptable range (refer to controller’s manual) or when the thermocouple is broken or malfunctions.
• Power failure protection resumes furnace operation right after the point of failure when power is reestablished.

NST 1600°C 16x12x12″ 40-Segment Muffle Furnace w/ PC Interface

NST-1600Muffle muffle furnaces feature a chamber with Mitsubishi (Japan) high quality alumina fiber insulation and molybdenum silicide (MoSi2) heating elements. A double walled steel internal housing helps minimize heat loss to exterior surface.

Furnace operation is controlled by Shimaden (Japan) 40-segment digital controller with built-in RS485 digital communications port and USB adaptor, allowing the user to connect to a PC for remote control and monitoring of the furnace. You can also save or export test results.

Features:

• Microprocessor based self-tuning PID control provides optimum thermal process with minimal overshoot.
• Built-in ammeter and dual voltmeters for easy monitoring and troubleshooting.
• Built-in computer interface.
• Long life type B thermocouple.
• CE compliant

Safety

• Overheat protection shuts down the furnace if temperature is outside of acceptable range (refer to controller’s manual) or when the thermocouple is broken or malfunctions.
• Power failure protection resumes furnace operation right after the point of failure when power is reestablished.

NST 1700°C 40-Segment Muffle Furnace w/ PC Interface

NST-1700 Muffle furnaces feature a chamber with Mitsubishi (Japan) high quality grade 1800 alumina fiber insulation and molybdenum silicide (MoSi2) heating elements. A dual-wall steel housing helps minimize heat loss to exterior surface.

Furnace operation is controlled by Shimaden (Japan) 40-segment digital controller with built-in RS485 digital communications port and USB adaptor, allowing the user to connect to a PC for remote control and monitoring of the furnace. You can also save or export test results.

Features

• Microprocessor based self-tuning PID control provides optimum thermal process with minimal overshoot.
• Built-in ammeter and dual voltmeters for easy monitoring and troubleshooting.
• Built-in computer interface.
• Long life type B thermocouple.
• CE compliant

Safety

Overheat protection shuts down the furnace if temperature is outside of acceptable range (refer to controller’s manual) or when the thermocouple is broken or malfunctions.

Power failure protection resumes furnace operation right after the point of failure when power is reestablished.

NST 1800°C 7x6x6″ Muffle Furnace w/ Kanthal (Sweden) Heating Element

NST -1800Muffle furnaces feature a chamber with Mitsubishi (Japan) high quality grade 1900 alumina fiber insulation and the famous Kanthal (Sweden) molybdenum silicide (MoSi2) heating elements. A dual-wall steel housing helps minimize heat loss to exterior surface.

Furnace operation is controlled by Shimaden (Japan) 40-segment digital controller with built-in RS485 digital communications port and USB adaptor, allowing the user to connect to a PC for remote control and monitoring of the furnace. You can also save or export test results.

Features:

• Microprocessor based self-tuning PID control provides optimum thermal process with minimal overshoot.
• Built-in ammeter and dual voltmeters for easy monitoring and troubleshooting.
• Built-in computer interface.
• Long life type B thermocouple.
• CE compliant

Safety

• Overheat protection shuts down the furnace if temperature is outside of acceptable range (refer to controller’s manual) or when the thermocouple is broken or malfunctions.
• Power failure protection resumes furnace operation right after the point of failure when power is reestablished.

Temperature Controller: Shimaden fp93 (Japan) with 4 programs and 40 segments (ie. 4 x 10 segments or 2 x 20 segments) Eurotherm temperature controller (optional)

NST 1100°C Compact Muffle Furnace (4x4x4″, 1.0L) with Programmable Controller

NST-DSP-KF1100 is a CE certified compact muffle furnace that offers high purity fibrous alumina chamber, gas inlet and outlet ports and a 30-segment, programmable temperature controller, and the furnace is with UL Certified electric components. It is the ideal muffle furnace for preparing small-sized sample using temperatures up to 1100oC in material research and dental labs with maximum energy saving. In addition, the compact furnace can be placed into a glove box to sinter samples in a vacuumed or controlled atmosphere.

Operating Temperature

• 1000°C max continuously
• 1100°C max for an hour
• 1200°C max for 30 minutes

Chamber Size

• Size: 4″x4″x4″  or 100x100x100 mm
• Capacity: 65 cubic-inch or 1 liter

Power

• 110V version: 950 W (15A Fuse) ( power cord is included )
• 220V version: 1.2KW(10A Fuse)

Temperature Controller

• PID automatic control and auto-tune function.
• 30 programmable segments for precise control.
• Built in protection for the over-heating and broken thermocouple.
• Large digital control panel (48 x 96 mm) for easy operation.

Application Notes

With the small footprint, low weight and low power requirement, it can be easily accommodated in a glove box and heat treat samples under protective gas.

Warnings

• Toxic or explosive gases are not recommended for use with this furnace without necessary safety controls and supervision. Please put furnace into fume hood for better safety.
• Small cracks may appear on the surface of the refractory ceramics over extended use. This is a normal occurrence and the cracks may be repaired with alumina coating.

Heating element

• The hot end roughness D1 of the silicon molybdenum rod is 7mm, the average manufacturer adopts 6MM, the heating end is thick, the surface load of the rod is low, and the service life is long.
• It adopts hot bending technology, with uniform resistance and long service life
• The length of the cold end of the Lu is 210mm, 400X300X300 furnace is 260, the general manufacturer adopts 180mm, and the cold end has a low temperature.
• The surface oxidation of silicon molybdenum rod is compact and can better protect the silicon molybdenum rod.

Install air switch and leakage protector:

When an electric current or leakage, an empty meeting automatically disconnects.

Can connect with computer

This furnace is equipped with communication interface and software, can be directly through the furnace computer control of each parameter, and can be observed from the computer PV on the stove and SV temperature value and instrument operation, the actual temperature of the furnace curve drawing computer real time, and can keep the temperature data of each time, can call up at any time.

Chamber

Imported VS Chinese

• High quality high pure alumina polycrystalline fiber cured furnace with vacuum suction and filter molding.
• Adopt Japanese technology to form.
• The spacing and pitch of the resistance wire in the furnace are arranged according to the best thermal technology of Japan, and the temperature field is simulated by thermal software
• Using 4 weeks heating, the temperature is more balanced The furnace can not remove powder, heat insulation, high reflectivity and temperature balance, which is strong against heat and shrinkage

Optional UL certified electrical board (all imported electrical appliances approved by UL)

Trigger VS Soft start limited flow trigger   Most of the manufacturers use the non – limited Xiamen botany trigger

• Phase shift trigger (with soft start and current limiting function)
• Current limiting function: no matter how the heating time is adjusted, the secondary current of our electric furnace after the transformer is limited to 170A, and the equipment is limited. Unlimited-flow triggers, if the heating rate is set wrong or too fast, The current is so large at low temperature that the device can trip or burn.
• Soft start function: the current will gradually increase when starting up, and the impact on the heating element will be small, which will help to prolong the life of the heating element
• Protection function: if the current exceeds the limiting current, the trigger will automatically cut off the trigger function to cut off the current protection furnace.

UL certified transformer

• The transformer cable is pure copper
• Small transformer
• Low temperature of transformer

The stainless steel tank of hydrogen atmosphere furnace is installed in the chamber of a stove or furnace a stainless steel tank, the tank oven door USES silicone O ring seal, in order to reduce O ring seal temperature in the furnace door is equipped with water cooling system, thermocouple, inlet valve, the valve installed on the tank, pressure gauge, etc; This furnace installation with hydrogen detector, burner, the combustion controller, alarm lights, torches, explosion-proof valve, etc., after gas after flow meter by chamber in and out, tail gas from the door of the oven after cooling water system. Can pass, argon, nitrogen, oxygen, hydrogen gases such as carbon monoxide, ammonia decomposition gas, &energy-saving equilibrium temperature field, the surface temperature is low, lifting speed, energy saving, clean furnace temperature is not easy to contaminated, universities, research institutes, industrial and mining enterprises do protect the sintering atmosphere, reducing atmosphere, skim the ideal product.

NST-1400C Atmosphere has many advantages of uniform temperature field, low surface temperature, heating or cooling promptly and so on. it is the ideal atmosphere muffle furnace for atmosphere protection sintering, atmosphere reducing in Industry, Scientific research institutes, Universities, which offer Heating element of Sic and double layer housing, phase-shift trigger, controlled silicon. Operation system is Shimaden 40-segments digital controller imported from Japan. The chamber is made of Polycrystalline alumina fibre. There is wind cooling system between the double walled housing to help the furnace heat or cool promptly. Sealed housing, silicon gel sealed cover, sealed door with silicon gel gasket and water cooling system, gas float through flow meter, then come out from back side, there are many gas inlets and gas outlets on the furnace with burning mouth, which can pre-vacuum and pass H2, Ar, N2, O2, CO, NH3 and so on.

• Temperature controller: Shimaden FP93 40 programmable segments (Shimaden fp93 made in Japan), It can separate into 4, 2, 1 programs, ie. 4×10 segments. FP93 have 6 PID controls, different PID are used for low, middle, high temperature for precise control.Over-temperature and over-current protection, shutdown automatically when thermocouple is broken( it will shut down power when temperature is higher than 1420 or thermocouples is broken, “ON” on the board is off and “OFF” is on)There is Fahrenheit (F) and Celsius (C) for option.With 485 communication interface: which can stop the furnace automatically.
• Cover opening protection system: overtravel-limit switch is installed to protect user, it will cut off power when the cover is opened.
• Chamber:it is imported from Japan,   good performance of heat preservation, high reflectivity, even temperature field, good ability of anti thermal expansion and cold contraction.
• Heating elements:This furnace is installed with Sic to ensure uniform temperature field and long service life.
• Leakage protection function:the furnace is installed with leakage air switch, it will cut off power Automatically when electricity leak or current exceed rated current.
• Software controlling system:this furnace can control every parameter directly and observe PV
• and SV on the computer by communication interface and software, computer can draw and save actual heating curve, it is convenient to call these dates at any time.
• Controlling system: Power control: Chint; Controlled silicon:Germany Semikron 106/16E; Trigger:Phase-shift trigger
• Gas system:floating flow meter or digital flow meter is for option to control gas Speed.
• Vacuum system: Vacuum level can be 10-1 or 10-4 with German molecular pump. TW-1.5 vacuum pump is for option.Pre-vacuuming can help remove air in the chamber quickly.

1400°C 40-Segment Muffle Furnaces w/ PC Interface

NST-1400 Muffle muffle furnaces feature a chamber with Mitsubishi (Japan) high quality alumina fiber insulation and silicon carbide (SiC) heating elements. A double walled steel internal housing helps minimize heat loss to exterior surface.

Furnace operation is controlled by Shimaden (Japan) 40-segment digital controller with built-in RS485 digital communications port and USB adaptor, allowing the user to connect to a PC for remote control and monitoring of the furnace. You can also save or export test results.

Features

• Microprocessor based self-tuning PID control provides optimum thermal process with minimal overshoot.
• Built-in ammeter and dual voltmeters for easy monitoring and troubleshooting.
• Built-in computer interface.
• Long life type S thermocouple.
• CE compliant

Safety

• Overheat protection shuts down the furnace if temperature is outside of acceptable range (refer to controller’s manual) or when the thermocouple is broken or malfunctions.
• Power failure protection resumes furnace operation right after the point of failure when power is reestablished.

NST 1600C High Temperature Microwave Sintering Furnace

High Temperature Up To 1600C Microwave Muffle Furnace

• Microwave heating.
• Temperature up to 1600 degree.
• Heating speed up to 50 degree per minute.
• No pollution to material.

Application Field:

• Claiming / synthesis of powder or particle materials:
• Electronic ceramic powders: barium titanate, barium-strontium titanate, strontium titanate, barium zirconate titanate;
• Lithium ion battery anode materials: lithium cobaltoxide, lithium manganate;
• Various colorants, glaze material, inorganic pastel;
• Alumina, magnesium oxide, zinc oxide, manganese dioxide, manganous-manganicoxide, zirconia, ammonium metavanadate, vanadium pentoxide, titanium dioxide, zinc carbonate, manganese carbonate, aluminum hydroxide, magnesium hydroxide, lithium cobaltoxide, zinc ferrite, Tri-chromatic rare earth fluorescent powder (Red), cement.

Synthesis / sintering of devices:

• Electronic ceramics: Piezoresistive element, thermistor, piezoceramics, microwave medium ceramics;
• Magnetic materials: hard magnetic, Ni-Zn, gyromagnet ferrites;
• Honeycomb ceramics, daily-use ceramics and glass ware;
• Oxide ceramics and refractory materials: alumina, zirconia, magnesium oxide and other oxide composites;
• Incineration, cremation, scaling loss experiments

Protection and Safety: Anode over voltage, anode over current, anode power surpass, electromagnet watchdog, magnetron temperature, external interlock. Control System: PLC (18 sections of temperature control), embedded system connected to laptop via USB, with data storage and printing functions.

NST 1200°C Muffle Furnace w/ Kanthal (Sweden) Heating Elements

NST 1200°C Muffle muffle furnaces feature the famous Kanthal(Sweden) spiral wire coils embedded in Mitsubishi (Japan) high quality alumina fiber insulation. A double walled steel internal housing helps minimize heat loss to exterior surface.

Furnace operation is controlled by Shimaden (Japan) 40-segment digital controller with built-in RS485 digital communications port and USB adaptor, allowing the user to connect to a PC for remote control and monitoring of the furnace. You can also save or export test results.

Features:

• Microprocessor based self-tuning PID control provides optimum thermal process with minimal overshoot.
• Built-in ammeter and dual voltmeters for easy monitoring and troubleshooting.
• Built-in computer interface.
• Long life type K thermocouple.
• CE compliant

Safety

• Overheat protection shuts down the furnace if temperature is outside of acceptable range (refer to controller’s manual) or when the thermocouple is broken or malfunctions.
• Power failure protection resumes furnace operation right after the point of failure when power is reestablished.

NST 1600°C 16x12x12″ 40-Segment Muffle Furnace w/ PC Interface

NST-1600Muffle muffle furnaces feature a chamber with Mitsubishi (Japan) high quality alumina fiber insulation and molybdenum silicide (MoSi2) heating elements. A double walled steel internal housing helps minimize heat loss to exterior surface.

Furnace operation is controlled by Shimaden (Japan) 40-segment digital controller with built-in RS485 digital communications port and USB adaptor, allowing the user to connect to a PC for remote control and monitoring of the furnace. You can also save or export test results.

Features:

• Microprocessor based self-tuning PID control provides optimum thermal process with minimal overshoot.
• Built-in ammeter and dual voltmeters for easy monitoring and troubleshooting.
• Built-in computer interface.
• Long life type B thermocouple.
• CE compliant

Safety

• Overheat protection shuts down the furnace if temperature is outside of acceptable range (refer to controller’s manual) or when the thermocouple is broken or malfunctions.
• Power failure protection resumes furnace operation right after the point of failure when power is reestablished.

NST 1700°C 40-Segment Muffle Furnace w/ PC Interface

NST-1700 Muffle furnaces feature a chamber with Mitsubishi (Japan) high quality grade 1800 alumina fiber insulation and molybdenum silicide (MoSi2) heating elements. A dual-wall steel housing helps minimize heat loss to exterior surface.

Furnace operation is controlled by Shimaden (Japan) 40-segment digital controller with built-in RS485 digital communications port and USB adaptor, allowing the user to connect to a PC for remote control and monitoring of the furnace. You can also save or export test results.

Features

• Microprocessor based self-tuning PID control provides optimum thermal process with minimal overshoot.
• Built-in ammeter and dual voltmeters for easy monitoring and troubleshooting.
• Built-in computer interface.
• Long life type B thermocouple.
• CE compliant

Safety

Overheat protection shuts down the furnace if temperature is outside of acceptable range (refer to controller’s manual) or when the thermocouple is broken or malfunctions.

Power failure protection resumes furnace operation right after the point of failure when power is reestablished.

NST 1800°C 7x6x6″ Muffle Furnace w/ Kanthal (Sweden) Heating Element

NST -1800Muffle furnaces feature a chamber with Mitsubishi (Japan) high quality grade 1900 alumina fiber insulation and the famous Kanthal (Sweden) molybdenum silicide (MoSi2) heating elements. A dual-wall steel housing helps minimize heat loss to exterior surface.

Furnace operation is controlled by Shimaden (Japan) 40-segment digital controller with built-in RS485 digital communications port and USB adaptor, allowing the user to connect to a PC for remote control and monitoring of the furnace. You can also save or export test results.

Features:

• Microprocessor based self-tuning PID control provides optimum thermal process with minimal overshoot.
• Built-in ammeter and dual voltmeters for easy monitoring and troubleshooting.
• Built-in computer interface.
• Long life type B thermocouple.
• CE compliant

Safety

• Overheat protection shuts down the furnace if temperature is outside of acceptable range (refer to controller’s manual) or when the thermocouple is broken or malfunctions.
• Power failure protection resumes furnace operation right after the point of failure when power is reestablished.

Temperature Controller: Shimaden fp93 (Japan) with 4 programs and 40 segments (ie. 4 x 10 segments or 2 x 20 segments) Eurotherm temperature controller (optional)

NST 1100°C Compact Muffle Furnace (4x4x4″, 1.0L) with Programmable Controller

NST-DSP-KF1100 is a CE certified compact muffle furnace that offers high purity fibrous alumina chamber, gas inlet and outlet ports and a 30-segment, programmable temperature controller, and the furnace is with UL Certified electric components. It is the ideal muffle furnace for preparing small-sized sample using temperatures up to 1100oC in material research and dental labs with maximum energy saving. In addition, the compact furnace can be placed into a glove box to sinter samples in a vacuumed or controlled atmosphere.

Operating Temperature

• 1000°C max continuously
• 1100°C max for an hour
• 1200°C max for 30 minutes

Chamber Size

• Size: 4″x4″x4″  or 100x100x100 mm
• Capacity: 65 cubic-inch or 1 liter

Power

• 110V version: 950 W (15A Fuse) ( power cord is included )
• 220V version: 1.2KW(10A Fuse)

Temperature Controller

• PID automatic control and auto-tune function.
• 30 programmable segments for precise control.
• Built in protection for the over-heating and broken thermocouple.
• Large digital control panel (48 x 96 mm) for easy operation.

Application Notes

With the small footprint, low weight and low power requirement, it can be easily accommodated in a glove box and heat treat samples under protective gas.

Warnings

• Toxic or explosive gases are not recommended for use with this furnace without necessary safety controls and supervision. Please put furnace into fume hood for better safety.
• Small cracks may appear on the surface of the refractory ceramics over extended use. This is a normal occurrence and the cracks may be repaired with alumina coating.