Pune, Maharashtra, India
Our Products
Specifications and Features
5 15 hp
Overview
MTR, SPK, MTH, MTApumps are vertical multistage centrifugal pumps designed for pumping of cooling lubricants for machine tools, condensate transfer and similar applications.The pumps are designed to be mounted on top of tanks with the pump stack immerged in the pumped liquid.
GrundfosMTR, SPK, MTH and MTApumps come with various pump sizes and various numbers of stages to provide the flow, the pressure and the length required.The pumps consist of two main components: The motor and the pump unit. The motor is a Grundfos standard MG motor designed to EN standards.
The pump unit consists of optimised hydraulics, various types of connections, a motor stool, a given number of chambers and various other parts.
Applications
The immersible pumps are suitable for liquid transfer in all applications where you have a tank. As main applications the following can be mentioned:
Features and benefits
Overview
TheGrundfos Hydro MPCbooster systems are made to the very highest standards. Thanks to the CU 351 controller, they handle even the most difficult boosting jobs with ease and accuracy.
All components have been combined with focus on quality and efficiency. TheGrundfos Hydro MPCbooster systems are Designed to last: sturdy, compact units with easy access to all service parts.Grundfos Hydro MPCbooster systems can be used wherever additional pressure is required. Each booster model has been designed to meet specific customer demands for capacity and control.
The intelligent cascade control ensures that the optimum number of pumps required to meet the demand runs at any time.Together with the CR with IE3 motors, this makes theHydro MPCthe most energy-efficient solution for maintaining a constant pressure during changing flow demands.
Applications
Features and benefits
Overview
Now, food industries can meet their strict hygienic requirements with a robust sanitary pump from Grundfos. TheF&B-HYGIApumps are single-stage, end-suction centrifugal pumps specially developed for the food and beverage industries hence the "F&B" in the name.
These compact units are designed for flexible use, allowing many different businesses to benefit from their reliable performance.
F&B-HYGIApumps are made from AISI 316 stainless steel in a compact design that makes them highly mobile and easy to fit into any system. One of the features that make this compact size possible is the plug-in shaft solution. This also makes service easier.
Applications
Features and benefits
Overview
Grundfos offers a wide range of dosing pumps representing state-of-the-art technology. Digital Dosing solutions (SMART Digital, DME, DDI) set new standards in liquid chemical handling and accuracy.
The operator can easily install and set up the pump to discharge exactly the quantity of dosing liquid required for the process in a unique drive- and flow-control management concept.
The setting of the pump is displayed in ml/h, l/h or gph, and the operation mode is easily identified by means of icons. The DMH mechanical hydraulic dosing pump range is the preferred choice for industrial and complex tasks. The DMH range is a series of extremely strong, robust pumps for applications where a substantial dosing range and high-pressurecapabilities are required.
Applications
The dosing pumps are designed for handling chemicals within the following applications, among others:
Features and benefits
Overview
The basicCRpump range, which can be applied in almost any industrial solution, is already in itself the broadest range available. Through our modular approach, we have made it even broader.
The basicCRpump range is available in four different materials: cast iron, two grades of stainless steel, and all-titanium. There are eleven flow sizes, capable of producing up to almost 50 bar of pressure, and with a variety of shaft seals, rubber materials and supply voltages.
Pump parts which are typically vulnerable to difficult liquids or particularly demanding operating conditions can be optimised for their purpose and designed for specific requirements.
Applications
CRpumps provide a complete range of pump solutions so that all applications, industrial and domestic, can benefit from the Grundfos touch. The applications that can be covered include the following:
Features and benefits
Overview
Grundfosend-suction pumps are used in water supply, industrial pressure boosting, industrial liquid transfer, HVAC (heating, ventilation and air-conditioning), and irrigation.
Grundfosend-suction pumps are multi-purpose pumps suitable for a variety of different applications requiring reliable and cost-efficient supply. End-suction pumps are used in five main areas of application: water supply, industrial pressure boosting, industrial liquid transfer, HVAC and irrigation.
TheGrundfosNB/NBGpumps are all non-self-priming, single-stage, centrifugal volute pumps with axial suction port, radial discharge port and horizontal shaft. TheNB/NBGrange consists of close-coupled pumps with their main dimensions in accordance with either EN733 or ISO2858.
Applications
Grundfosoffers a virtually limitless range of close coupled (NB) end-suction pumps. Their sturdiness and reliability make them ideal for use in demanding environments such as the following:
Features and benefits
Overview
Enabling numerous customised solutions. The pump basically consists of a series of interchangeable modules, all of which have been designed to work together seamlessly, no matter the application.
The pumps are of the close-coupled type, with a mechanical shaft seal.TheCMVpumps are available with cast-iron base and discharge part whereas the remaining wetted parts are made ofstainless steel (AISI 304/DIN 1.4301).
Applications
While each GrundfosCMVpump can be customised to meet individual requirements, the pump family is designed to be used in a wide variety of applications.
These include
Features and benefits
Overview
TheGrundfosBMEXpump system is suitable for water treatment applications handling seawater and brackish water desalination.
Its special design to handle desalination features all wetted parts in seawater execution. For instance, all pump materials which are in contact with the seawater are made from 904L or duplex stainless steel.
In addition, the materials in contact with water in the pressure exchanger are made from duplex stainless steel and ceramic.
The BMEX booster system consists of:
Note: Base frame and manifold are optional for the X-Changers.
TheBMEXbooster system is based on the hydraulics ofGrundfosSP_R submersible pumps and an ERD (Energy RecoveryDevice).
The booster system is used for:
Applications
Desalination of brackish water and seawater.
Features and benefits
TheSEGrange of grinder pumps fromGrundfosis specifically designed for pumping effluent and untreated sewage in small communities or sparsely populated areas with no sewer systems or where gravitation systems are unsuitable.
Pressurised systems are the perfect choice for transfer of effluent and sewage, and theSEGrange combines cost-effectiveness with maximum protection for the environment by facilitating the use of smaller pressure pipes for minimal investment costs.
TheSEGrange is designed to reduce energy consumption and to keep downtime costs to a minimum, while maintaining peakperformance throughout the system life.
Applications
TheGrundfos SEGpumps are specifically designed for pumping untreated wastewater from domestic, commercial or municipal sources. The high discharge pressure enables transfer of wastewater over longer distances.
Features and benefits
Rotary lobe blowers used to increase the capacity of the primary vacuum pumps when operating at their minimum suction pressure (as a booster).The RBS/AV blowers must be used in series with a primary vacuum system ( VP ) and for pressures lower than 50 mbar absolute.The main characteristics of these blowers are as follows:
-two conjugate rotorswhich rotate inside a special design casing with tight clearances in all position, assuring gas sealing without contact between parts-the labyrinth sealsavoid the atomized oil to enter into the compression chamber.-the sealing between compression chamber and environment is ensured by O-rings seals, set between ground surfaces.-The shaft end sealing is made by two seal rings in VITON with opposite lips lubricated by means of a fitted on oiler.The oil ring housing can be cooled by water circulation.-the shaft is protectedby an hardened replaceable sleeve.- Suction of gases and vapours;- No sliding parts, therefore no wear;- Safe operation and minimum maintenance;
Robuschi can supply primary vacuum systems consisting of liquid vacuum pumps with deliveries up to 4, 200 m/h.
Grundfos TP and TPEvertical in-line pumps are used in a variety of applications. The pumps are all single-stage, in-line centrifugal pumps with standard motors and mechanical shaft seals. The pumps are of the close-coupled type, i.e. pump and motor are separate units. Consequently, the pumps are less sensitive to impurities in the pumped liquidthan similar pumps of the canned rotor type.
Two different models of vertical in-line pumps are available. Please note that there are a number of specific productvariants available for each model. Detailed information on these variants can be found inGrundfos WebCAPS.TPpump model is notable for its high levels of reliability and efficiency. Quiet, highly-efficient IE3 motors are standard components. AllTPpumps are electro-coated to ensure high corrosion resistance.
The main difference betweenTPandTPEpumps is the motor. TPE motors have a built-in frequency converter, allowing different control methods to be employed.TPEpumps offer benefits with respect to energy savings and increased comfort.
Applications
These vertical in-line pumps are used in commercial buildings for air conditioning and heating applications.The pumps are all single-stage, in-line centrifugal pumps with standard motors and mechanical shaft seals. The pumps are of the close-coupled type, i.e. pump and motor are separate units. Consequently, the pumps are less sensitive to impurities in the pumped liquid than similar pumps of the canned rotor type.
Features and benefits
Overview
Grundfoshigh-pressure booster modules are used for boosting, liquid transfer and circulation in systems under high static pressure. Applications include reverse osmosis in domestic water supply, hospitals, laboratories, and the chemical, electronics and metals industries. The pumps are also used for ultrafiltration in the chemical and galvanising industries, painting workshops, and the metals and mineral industries.
Available in three SS qualities, SS 304, SS 316, SS 904 L.
Applications
The booster modules are suitable for pressure boosting in such systems as:
Features and benefits
Grundfos SPsubmersible pumps are renowned for their high efficiency and reliability throughout the range. Made entirely of corrosion-resistant stainless steel, SP pumps are ideal for a wide variety of applications.
Grundfos SPpumps represent state-of-the-art hydraulic design. Built to deliver optimum efficiency during periods of high demand, the SP pumps provide low long-term costs and high operating reliability regardless of the application.
TheGrundfos SPrange offers high efficiency, high resistance to sand and other abrasives, motor burnout protection, and easy maintenance. A complete monitoring and control system is available for constant optimisation of the pumping system.
Applications
The pumps are suitable for:
Features and benefits
Overview
Grundfos NK/NKGpumps are used in water supply, industrial pressure boosting, industrial liquid transfer, HVAC (heating, ventilation and air-conditioning), irrigation and process industries.
Grundfosend-suction pumps are multi-purpose pumps suitable for a variety of different applications requiring reliable and cost-efficient supply. End-suction pumps are used in five main areas of application: water supply, industrial pressure boosting, industrial liquid transfer, HVAC (heating, ventilation and air-conditioning), and irrigation.
The pumps are all non-self-priming, single-stage, centrifugal volute pumps with axial suction port, radial discharge port and horizontal shaft. TheGrundfos NK/NKGrange comprises a complete series of long-coupled pumps that comply fully with either EN733 or ISO2858. The pumps are of the back pull-out design, enabling removal of the motor, coupling, bearing bracket and impeller without disturbing the pump housing or pipework. Even the largest pumps can thus be serviced by one person with a crane. The ISO2858 range of pumps are available with a bearing life of 100, 000 hours, and can be fitted with double seals. They available in a stainless steel version as an option.
Applications
Grundfosoffers a virtually limitless range of long-coupled(NK)end-suction pumps. Their sturdiness and reliability make them ideal for use in demanding environments such as the following:
Features and benefits
Overview
The most robust pump designed ever for water pressure boosting It was once said that great things come in small packages. When you meet theGrundfosCM booster pump for the first time, youll certainly agree. This horizontal multi-stage pump has been created with compactness and modularity as two of its central features. Add reliability and quiet operation to the mix, and another innovative pump solution fromGrundfosis born.
Centrifugal modular. The pump is basically composed of a series of interchangeable modules, all of which have been designed to work together seamlessly, no matter the application
Appliications:
CM pump with pressure controller is used for constant water pressure. Can be ideal when space is constraint near overhead tank. It also has dry running protection, incase of no water in the pipeline.
CM pump is also supplied with pressure tank for constant water pressure. When the pressure drops to the pre-set level, the pump will start-up and when the water consumption drops again, the outlet pressure will rise to a pre-set stop pressure after which the pump will stop. Available from 8 lts to 100 lts tank range.
Features:
Construction:
TheLBseries from CompAir represents a new generation of fixed speed rotary screw compressors, which incorporate the best of CompAir technology, design and quality, to deliver reliable, economical and efficient performance in a completely new package.
Available in air or water cooled versions, theLB55 to LB90fixed speed rotary screw compressors have a power range of 55 to 90 kW and deliver high quality air at volumes of 9.5 to 15.3 m3/min, with a pressure range between 7 and 10 bar.
CompAirs commitment to quality ensures that theLBseries offer the highest levels of reliability and performance with low operating costs throughout the compressors life.
Key Benefits
Technical Data
| Compressor Model | Motor Rating kW |
Free Air Delivered (m3/min)* |
Dimensions (mm) LxWxH |
Noise level** dB(A) |
Weight (kg) |
||
| 7 bar g | 8 bar g | 10 bar g | |||||
| LB55 | 55 | 10.7 | 10.5 | 9.5 | 2104 x 1300 x 1580 | 72 | 1400 |
| LB75 | 75 | 13.8 | 12.5 | 10.6 | 2104 x 1300 x 1580 | 74 | 1450 |
| LB90 | 90 | 15.3 | 14.9 | 13.8 | 2104 x 1300 x 1580 | 75 | 1500 |
