Multitech Scientific Instruments

Anand Parbat, Delhi

$pillar or plate type heavu futy load frame

PLC based touch screen controller

Pace rate controlled from 1 kn to 10 kn/sec

Autoreport generation

Auto saving of reports

Huge storage capacity of results (10000 Logs)

Report download facility through scanner on phon

220 V, AC supply, 50 Hz

Specification:

Same as MSI 9011 but supplied with Digital Temperature Controller range ambient to 100.0 deg C accuracy 0.2 C, least count 0.1 C.& FHP Motor cum Stirrer. Heaters are provided according to the size of the chamber .A control panel in which the digital controller, switches for mains, FHP stirrer, regulator for the stirrer is fit is by the side. Sizes available: 18"x12"x10" inner chamber in stainless steel, outer in mild steel. Rating of heater 2000 W suitable to run on 230 V A.C. Single Phase.

MSI

IS 1237, IS 1706 Specification:

This is used for determination of resistance to wear for Cement & Concrete flooring tiles.

Tiles specimen of size 7.06 cm x 7.06 cm is pressed face-wise under specific load on a grinding

path and abrasive powder is evenly spread on the rotating grinding disc the second parallel

side of the tile is subjected to wear for similar number of rotations. The wear of the tile is

measured on a thickness gauge specifically made for the purpose. The machine consists of a

disc rotating at a speed of 30 R.P.M. in a circular tray. A bracket is provided to hold the

specimen. A counter balance lever loads the specimen. Load applied is 30 Kgf. A funnel is

fitted to evenly spread abrasive powder on the grinding path. A Pre-set Counter

automatically stops the machine after 22 revolutions. This counter is Re-adjustable. The

machine works on 440 V A.C. Three Phase electrical supply. On request machine to operate

on 230 V A.C. Supply can also be supplied.

EN 123902; ASTM C31, C192; AASHTO T23, T126

22 mm hand-held, 220-240 V 50-60 hz

The poker vibrator is ideal for the internal compaction of concrete specimens and a good alternative to traditional tamping bar, especially when there are large numbers of specimens to be compacted. Flexible shaft length and tip diameter can be selected from the four available products.

Standard Used : AASHTO T 256

Lightweight Aluminium construction

Ease of Transportation Unique Telescopic Design Simplifying Field set up 

Compact,

Thereby reducing the amount of storage space needed Benkelman Beam utilizes the technique of using balanced beam in conjunction with a suitable vehicle to measure road flexure The improved Benkelman Beam is a convenient, accurate device for measuring the deflection of flexible pavements under moving wheel loads. Operating on a simple lever arm principle, the unit consists. Supplied with carrying case Note: Benkelman Beam with Digital Dial Gauge also available at an extra cost 

Standad Used : IS 1888 1962, ASTM D 1194, BS 13779

This is for estimating the bearing capacity of shallow foundations in situ and for the design of flexible pavement. In the test procedure a steel plate is subjected to gradually increasing load and settlements of the plates recorded.

Specification : The out fit consists of 50 tonne hydraulic jack with separate pumping unit fixed to it a 0 - 500KN x 0.5KN. Pressure gauge and flexible metal pipe 5 mtr. long

Special ball and socket arrangement

Extension rod 12mm dia x 25 cm long

Magnetic base with female thread on top for holding extension rod

Top end plate, 50mm, dia with male thread for fitting onto the extension rods and positioning the dial gauge plunger

Column 15cm dia x 25cm long with flanges complete with four bolts and nuts

Column 15cm dia x 50cm long with flanges complete with four bolts and nuts

Bridge support of welded steel angle construction, 5 mtr. Span and stands approximately 30 cm. High. Fitted with two quick release clamps a for positioning and holding the dial bracket 

This is for determining the lateral extension of 150 mm dia x 300 mm high cement concrete cylinders while testing them under compression.

Specification :

The unit consists of two movable frames pivoted at one end. The extensometer is fixed to the specimen with the help of tightening screws. The lateral extension is indicated on a dial gauge of 0.002 mm x 5 mm is mounted on the upper ring and the tip of the dial gauge rests on an anvil. The zero on the dial gauge can be set by adjusting the anvil screw. Supplied in a wooden carrying case.

Electrical Heating with Immersion Heating Elements and Dimmer stat for controlling the temperature. Suitable for operation on 230 V, 50Hz, Single Phase , A.C. supply. Supplied complete with 10mm cup and valve.

For determining stripping value of bituminous mixes having aggregate size: 1.0mm to 75 micron.

Specification: A circular tray rotates in a vertical plane at a rate of approximately 100 R.P.M. by an electrical geared motor. 4 bottles of approximately 400 cc are mounted on this circular tray at an angle of 900. To each other with their mouth towards center of the tray. A time switch is provided. Suitable for operation on 230 V A.C. Single Phase

Easily affordable, tough total stations, built specially for site work. Anybody can use, regardless of profession no experience needed. Fast, reliable angle & distance measurements. Stake out. Excellent in-built laser distance measure.Simple routines for any building and construction tasks.

For anybody working on or around a site with the need of a simple, intuitive, yet innovative, long-lasting and powerful measuring tool. It is designed a perfectly tailored tool for every construction job. Regardless of your profession, Builder will amaMSIngly accelerate your work flow. From simple tasks to professional all-day use, the Builder Series offers a scalable product family that exactly meets your needs.

Builder Series is equipped with all of the above features plus wireless com-munication via Bluetooth, full laser distance measurements up to 250m/820ft and up to 1.5mm accuracy at 100m covers the full range of tasks to be performed on any construction site. An -30C option is available additionally.

Specification : Carries upto 7 sieves of 150 or 200 mm diameter. The shaker is driven by a 1/4 H.P. Motor through a reduction gear immersed in oil. The sieve table does not rotate but is inclined from the vertical axis and the direction on inclination charges progressively in clockwise direction. If the stop pin below the table is removed, the shaker can have a rotary motion. In addition to this gyratory motion of the table, there is an upward and downward movement ensuring that each square cm of the sieve is utilized. A pair of rods and a holder can be fixed on the top of the upper most sieve, and thus the sieve set in firmly held. Suitable for operation from 230 V 50 Hz, Single phase A.C. supply. a) Adopter for 300 mm dia. sieve available at extra cost b) Adopter for 450 mm dia. sieve available at extra cost 

Standard Used : ASTM D2-33 & IS 2386 (PART IV)

Used for The Determination of Resistance of Aggregates to Wear by Abrasion.

Specification: It consists of two hollow cylinders closed at one end and provided with Fitting covers at the either end. These cylinders are mounted an a shaft at angle of 300 with the axis of rotation of the shaft. The shaft rotates at 30-33 RPM. Through a reduction gear operated by a motor and is provided with a revolution counter. Complete with Abrasive Charge consisting of 12 Nos. Hardened steel Balls of 48mm dia. Suitable for operation on 440 Volts, Three Phase, 50 Cycles, A.C. supply. Note : Option of Digital Preset Counter can be provided at an Extra Cost

A straight edge approximately 3 meters in length may be used to determine lateral surface regularity of a road surface. This lightweight apparatus is made up of mild steel or aluminum as per customers requirement and is equally supported at both ends producing a set height between the road surface & the beam. Any vertical irregularity is measured using incremented wedges. 

This is yodar type, motor driven sieve shaker for carrying out wet sieve analysis of materials. Specification : Consists of a water reservoir and a holder for sieves, which can take up to 7 sieves of 150mm or 200mm diameter. Shaker is driven by a ¼ H.P. motor through a belt drive. Shaker mechanism moves the sieves up and down in the reservoir. The reservoir has a water out-let for draining out the used water. Suitable for operation 230 V A.C. Single Phase 

We are offering Brunton Compass Pocket Transit Type that is appreciated for its quality and reliability. The Brunton Compass is used to measure strike, inclination and topography skeleton survey.We make sure that the Brunton Compass is at par with industry standards and as per the specifications laid by our clients. Avail precision made Brunton Compassfrom us at very reasonable prices.

Features:

Precision made. Sturdy. Accuracy. Smooth finishing

Safety Helmets that are essential for head protection during construction jobs and mining process. Safety Helmets are fabricated using robust material that are capable of withstanding harsh conditions and provide optimum safety to the users from any kind of injuries. Suitable for construction works, material handling, mining, sand blasting, ports etc. Made with hard PVC.

Standard Used : ASTM D2172, AASHTO T-58, T-164.

Specification: The Instrument is used for determination and checking of Bitumen percentage in Bituminous mix, the mix is added with a solvent and dissolved bitumen is removed by centrifugal action. Consists of a removable Aluminum rotor bowl, Capacity 1500 gms. With a cap and tightening nut. The bowl assembly is mounted on a vertical shaft, which protrudes from a cast housing. This shaft and thus the bowl is rotated fast manually by enclosed gears in the cast body and handle. Solvent is introduced during the test through the holes in the cap of the housing. A drain is provided to collect dissolved Bitumen coming out of the rotating bowl and getting collected in the housing.

Available from 10 Ton to 300 ton capaity

Available in manual to fully automatic model

4 pillar / H frame/ C frame type

Programmable PLC

Usefull for various industries like rubber mouldin

Table Mounted

Stable Construction

Feed arrangement for cutting

Feed arrangement for cutting Cooling water arrangement

Specification: This unit is designed for cutting and grinding cylindrical rock specimens upto NX size. The outfit includes 200mm dia diamond impregnated cutter, a fine diamond impregnated grinding wheel a water supply system and sampler holder. A V-Vice, to hold the sample up to 55mm dia x 140mm long to be cut parallel and square to the longitudinal axis is provided. Cores longer that 140mm can be prepared by reversing the specimen and holding MSI 6006 against the vice, A hand feed arrangement is provided to facilitate the specimen with a uniform and smooth feeding motions. This unit is provided with a 3 HP, Three Phase, 440 V A.C. Motor.

Point Load Test Machine is used to determine the strength values of a rock and concrete specimen both in the field and in the laboratory. It consists of a load frame for applying loads up to 100 KN, on which a manual hydraulic jack is mounted. The instrument accepts core specimens up to 102 mm diameter which are loaded by two cone shaped points. A graduated scale indicates the distance between the conical points. The applied load is measured by a pressure. transducer with a digital display unit range 0-100 KN

Standard Used : ASTM D2172 AASHTO T-58, T-164

Specification: Centrifuge Extractor, Electrical Operation, Capacity 1500g, with a Dimmer stat for speed control from 2, 400 to 3, 600 rpm. Suitable for operation on 230 V, 50 Hz, Single Phase, A.C. supply.

Standard Used : IS 2386 (PART-1) & BS 812

Specification: Consists of a hard wood base with vertically mounted metal studs as Specified in the IS 2386 (Part-1) & BS 812.

Standard Used : IS 2386 (PART-III) & BS 812

Specification: It Determines Bulk Density or unit weight of aggregates. It consists of a Calibrated Cylindrical Measures of sheet iron with handles.

Capacities available 3, 5, 7, 10, 15, 20 & 30 liters.

Complete with One Tamping Rod 16mm dia x 600mm long both ends rounded.

The digital display with its large numerals makes it very simple to use this Dial Gauge. Function and display section can be rotated through 270. The sturdy construction guarantees precision and reliability.

Features: Button function: on/off, inch/mm, zero Cr2032 battery, automatic power off Data output Optional accessory: data output system, backs, contact points

Specification:

Oven are designed, calibrated & tested to suitable various applications in growing fields.

Construction:

Double walled constructed with inside Aluminium / Stainless Steel chamber having 60-75 mm glass wool insulation. Door is Fitted with heavy chrome plated hinges. Provided with adjustable Steel / Aluminium / Wire mesh trays. Temperature is recorded by means of L shaped thermometer fitted at the front of the cabinet.

Temperature controlled by hydraulic capillary thermostats.

Heating:

Heating elements are made up of high grade (KanthaI) resistance wire heaters are fitted/wound along all the sides of the oven.

Complete with two pilot lamps, plug pins.

Temperature Gauge:- Ambient To 250 1 C

(i) Air circulation can be fitted in all the sizes mentioned above for proper air circulation at an extra cost.

(ii) D igital temperature indicator cum controlled can be fitted for b etter accuracy results.

(iii) Alarm system can be fitted at an extra cost. (iv) For higher temperature i.e. 200 C always buy

QUALITYTEST caps are steel reinforced and conform to state and federal safety regulations. Complies with BIS specifications Made of engineered high-impact plastic. 16 sq. inches top surface area aids in protection. Fits a range of diameters. Self-centering formed steel insert seats cover perpendicular to rebar.

Standard Rockwell / Brinell Machine

The Hardness Testers have been designed and manufactured strictly conforming to IS. BS, ASTM, ISO and DIN Standards. Since 1966 for most exacting test requirements in the Laboratories and Workshops etc. These testers are designed and manufactured for measuring hardness of metals and alloys of all types, hard or soft, flat, round, tubular or irregular in shape. The testers are simple in design, easy to operate, yet very reliable and accurate. Standard Rockwell Method-Manual Operation

MSI 7003A: With automatic zero setting dial guage and manual load selection.

MSI 7003B: With automatic zero setting dial guage and Automatic load selection Standard Rockwell/Brinell Method-Manual Operation

MSI 7003C: With automatic zero setting dial gauge device and automatic toad selection. Brinell Hardness Testing facility according to 30 F/D ratio, with 187.5 kgf load and 2.5 mm dia ball indenter.

MSI7003D: Similar to MSI 7003C, but with additional test Ioad of 250 kgf and 5 mm dia ball indenter for, testing Brinell hardness of non-ferrous metals according to 10F/D ratio.

LOS ANGELES ABRASION TESTING MACHINE

IS 2386 (PART IV) ASTM C 131, AASHTO T-96

Used for testing Crushed Rock, Crushed Slag, Crushed and Uncrushed Gravel For Resistance to Abrasion.

Specification:

The machine consists of a hollow cylinder mounted horizontally on a study frame on ball bearings. There is an opening which can be closed with a dust tight cover to facilitate charging and discharging the drum with the material under test. A detachable shelf which extends throughout the inside length of the drum which catches the abrasive charge and does not allow it to fall on the cover. The drum is rotated by an electric motor through a heavy reduction gear at a speed of 30-33 R.P.M. A revolution counter is fitted to the frame. A tray is supplied for collection of the material at the end of the test. Complete with Abrasive Charge consisting of a set of Twelve hardened steel balls, approximately

Standard Used : BS 812

Used for Testing Aggregates for Resistance to Abrasion.

Specification: It consists of a disc rotating about a shaft connected to a reduction gear box coupled to a motor. The disc rotates at 28-30 RPM. Under the rotating disc is a tray with an outlet to facilitate the removal of sand. Two Conical Hoppers are mounted on a bracket fixed to the circular tray. An arrangement is made for start and stop the flow of sand. Two containers with weights are supplied to keep the specimens pressed against the rotating disc. Suitable for operation on 220 V, 50 cycles, A.C. Supply.

Standard Used : IS 2376 (PART-IV) & BS 812:111

For Measuring of Resistance of Aggregate to Crushing.

Specification: The Aggregate Crushing Value (ACV) test set provides a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Each set consists of steel cylinder, plunger, base plate, cylindrical measure and tamping rod. All parts of the apparatus are powder coated or galvanized steel, heat treated and ground before manufacturing to make it durable and reliable. Specification: Consists of M.S. Cylindrical Container 150mm +/-0.5mm dia x 130mm to 140mm high with base plate 200 to 230mm/sqr x 6mm thick. A Plunger of 148mm +/-0.5mm dia x 100 to 115mm high. Supplied complete with Tamping Rod, 16mm dia x 600mm long, both ends rounded. Metal Measure 115+/- 0.5mm dia x 180 +/- 0.5mm high.

Note: On Special Request Aggregate Crushing Value Apparatus having 75mm dia or 300mm dia cylinder size can be supplied.

Standard Used : IS 2386 (PART III) & BS 812

The buoyancy balance system consists of a rigid support frame, incorporating a water tank mounted on a platform. A mechanical lifting device is used to raise the water tank through the frame height immersing the specimen suspended below the balance. The balance supplied may also be used as a standard weighing device, thus providing a versatile and comprehensive weighing system in the laboratory

Specification: The outfit comprises of

Electronic balance, capacity 10 kg. Least Count 0.1gm, provision is made in this balance to suspend density basket under material pan. This balance is mounted on an angle iron frame stand.

Density basket.

Air tight container to suspend density basket.

GI Tray of area not less than 650 cm sq.

Absorbent cloths 75cm x 45cm. 

MSI 4023-A Automatic Marshall Stability Test Machine, 50 KN, 220-240 V 50-60 HZ MSI

4023-B Breaking Head (Stability Mould) 4”1 Pkt.MSI 4023-C Linear Potentiometric, Displacement Transducer, 25x0.001 mm with Bracket for MSI 4023-A and MSI 4023-B MSI 4023-D Indirect Tensile Splitting Device for Compacted Bituminous Samples 100 mm (4") Dia. EN 12697-34, 12697-23, 12967-12, ASTM D1559, D5581, D 6927; AASHTO T245 The 50 kN capacity Automatic Marshall Stability Test Machine is used to determine the maximum load and flow values of bituminous mixtures. The machine comprises of a robust and compact two column frame with adjustable upper cross beam. The unit is a bench mounting compression frame with motor and worm gear housed within the base unit. The speed of the lower platen can be adjusted between 6 mm/min to 60 mm/min using the data acquisition and control unit. For safety, the up and down travel of the lower platen is limited the use of limit switches. Rapid

Standard Used : IS 2386 (PART-1) & BS 812

Specification: Used for determining the Flakiness Index of Aggregates. It Consists of a frame with a sliding panel. The Panel has slots of Different Standard Lengths and Widths accurately Cut.

Standard Used : IS 2386 (PART IV) 9377 & BS 812:112

It is robustly designed to determine the aggregate impact value (AIV) of aggregates which provides a relative measure of the resistance of an aggregate to sudden shock or impact. The counter fitted to the machine automatically records the number of blows delivered to the sample, manufactured from heavy duty plated steel to resist corrosion. Specification: The instrument consists of a circular base with Two vertical guides. The Hammer of weight 13.75 +/-0.25kg can be raised to fall freely down the vertical guides. The Height of fall can be adjusted through 380 +/- 5mm. The Hammer is provided with a locking arrangement. The hammer falls freely to the base and is removable for employing. Supplied complete with metal measure 75mm dia x 50mm high (For specimen preparation) and Tamping Rod 230mm long x 10mm diameter. A Blow Counter to count the number of strokes is fitted on top of the equipment.

Standard Used : IS:6932(PARTVIII), ASTMC230, BS4551:1

FlowTableisusedfordeterminingthework-abilityofbuildinglimes.

Specification:

Theflowtableconsistsofa30cmdiapolishsteelplatewith3engravedannularcircles7, 11and19cmdia.Thetabletopisarrangedforafreefallof12.5mmbyacamaction.Suppliedcompletewithonebrassconicalmould, 65mmi.d.atbaseand40mmi.d.attop, heightofthemould90mm.

Form professional looking tapered holes in concrete to receive posts for railings, awnings, and other common uses. Simple installation. Easy to strip/remove - just pull tab. Holes can receive square posts up to 2 or 2 pipe (2 3/8 OD) Accurate alignment - tip of tab is centerline of hole form Use with any concrete thickness Pre-install for slabs up to 6 thick High visibility Safe to use - no sharp edges

Model Rail Diameter Box Qty.

MSI 8002-A Up to 2-3/8" OD 25

machine is designed with a Hydraulic Power pack and control circuit for effortless loading unloading operation. A dial gauge in front measures depth of ball penetration. This facilitates production testing within tolerance limits by comparison method.

Standard Accessories

Model Capacity 3000 Kgf

PMT 3 Testing Table 200 mm

Testing Table 200 mm with 'V' grove

pc. For round jobs-l0 to 80 mm dia

pc. Ball holder 5 mm

pc. Ball holder l0 mm

pc. Test Block HB-5/750

pc. Test Block HB-l0/3000

pc. Brinell Microscope

pc. Allen Spanner

pc. Telescopic cover for elevating screw protection

set Instruction Manual

book

IS 516, ASTM C-29, C-31, C-57, C-138, C-192 AASHTO T-29 & T-23 Specification:

This is used for compacting concrete into cube moulds. This rod is made of steel it is 16 mm dia., 600 mm in length and rounded at both ends.

Level Staff is a graduated aluminium rod, used with a levelling instrument to determine the difference in height between points or heights of points above a datum surface. It cannot be used without a leveling instrument.

Multitech Scientific Instruments provide a range of levelling staffs including E-type, bar coded, standard invar and industrial Invar Levelling Staffs. Most of the staffs are sectional and so can be adjusted in length to allow for easy storage and transport. The aluminium staffs adjust with telescopic section inside each other, whilst the wooden versions use sliding slip joints or connections. Sizes: 4/5/6 metres.

The right choice for the demanding professional user. Here you get the best value for money without making any compromises on the well known QUALITYTEST virtues. Quality, durability and efficiency completely lives up to even the highest demands.

Features:

1. Large motor with plenty of power
2. Large Transport wheels
3. Can be operated by one man
4. Maintenance free High Quality gears