Mts Incorporation

Urban Estate Phase 2, Jalandhar, Punjab

• Friction surface material is Chrome leather.
• Back surface material is Chrome leather.
• The belt factor is 5 N/mm at 1% elongation for product code MTS 50LL, 7.50 N/mm for MTS 75LL, 10 N/mm for MTS 100LL, 15 N/mm for MTS 200LL, 23 N/mm for MTS 300LL, 30.50 N/mm for MTS 400LL.

MTS V-BELTSARE MANUFACTURED UNDER STRICT VIGILANCE AND OBSERVATION OF THE STATE OF ART OF MODERN TECHNOLOGY WITH REINFORCEMENT OF HIGHLY SHOCK - LOAD RESISTANT SYNTHETIC CORDS COMBINED WITH SPECIAL RUBBER COMPOUND AND ULTIMATELY JACKETED TO OBTAIN MAXIMUM LlFE AND SMOOTH RUN OF THE DRIVE.

.Cover. The bias-cut cover fabric is impregnated with special rubber to protect the inner part of the belts and provide strong abrasion resistance on the pulley groove.

B.Tension Member. The load carrying cords are tough polyester / aramide cords that have been specially treated to temper the cords to their point of high strength, low elongation and greater resistance to bending fatigue.

C.Top Compression Section. The rubber used in this section is compounded to withstand sudden shock loads and to keep the belt flexing readily when passing over the pulleys.

D.Insulation Section. The insulation section holds the tension binding section for extra strong adhesion between cords and the top and bottom compression section.

E.Bottom Compression Selection. This section holds the normal cross section of the belts and is compounded to resist compression fatigue and heat for longer service life.

Width: 300 mm to 1800 mm in steps of 50 mm.
Length : Open or endless upto 200 mtrs in single length
Fabrics plies : 2 plies to 8 plies
Fabrics : Polyster Nylon (EP) EP 100, EP 125, EP 150, EP 200, EP 250, EP 300, EP 350 , EP 400 and EP 450
Nylon Nylon (NN) NN 100, NN 125, NN 150, NN 200, NN 250, NN 300, NN 350, NN 400 and NN 450.
Cotton Cotton 28 OZ, 32 OZ, 36 OZ, 42 OZ, 48 OZ and for elevator belts 34 OZ.

X Mechanical Fasteners not recommended.For Specific requirements not covered in above table, please contact with details. The figures mentioned above are approximate values for consideration for drive design. and are subjected to change without notice in the make of fresh developments.

Cover Grades: Cover type Tensile strength Elongation at break General Applications Specific.

Kg/cm2 (Min.) (% Min.)
M-24 240 450 Suitable for rugged services for conveying crushed Metallic ores, Lime stone, Granite etc. Also suitable for large size ores. IS-1891, (Part-I)-1994N-17 170 400 Suitable for Materials, like Asbestos, Ash, Bauxite, Cement lime etc. IS-1891, (Part-1)-1994HR(T1) 125 350 Suitable for Transporting hot material (Upto 125oC for coarse material and 100oC for fine material) IS-1891, (Part 2)SHR(T2) 125 350 Suitable for transporting hot material (Upto 150oC for coarse material and 125oC for fine material) IS-1891, (Part 2)OR (Oil Resistant) 120 250 Cover Grade of specially blended synthetic Polymers is designed to give very high resistance to mineral vegetables and Animal Oils & Fats. IS-1891, (Part 3)FR (Fire Resistant) 170 350 Recommended for use in surface applications in coal and such type of mines where the ambient temp. may not be high but there is distinct hazard of belts being enveloped in fire. Rubber covers are fire resistant and anti static. CAN/CSA/M-422/ M-87 & IS-1891 (Part 5)

• Friction surface material is NBR elastomer.
• Back surface material is NBR elastomer.
• For MTS 50R 12, 1.20mm thickness belt, friction surface material is NBRelastomer and back surface material is NBR film.
• The belt is having Anti-static properties.
• The minimum pulley diameter at 20 deg. C is 25mm for product code MTS 50R , 40mm for MTS 75R, 60mm for MTS 100R, 110mm for MTS 200R.
• The belt factor is 5 N/mm at 1% elongation for product code MTS 50R, 7.50 N/mm for MTS 75R, 10 N/mm for MTS 100R, 15 N/mm for MTS 200R.