Product / Services
Post Buy Requirement

My ExportersIndia

For Buyer

For Seller

For Help

ME

MTMS ENGINEERS PRIVATE LIMITED (formerly Known As Material Testing Mac
location Sanghvi, Pune, Maharashtra

Write a Review
Call Now Call Now

Our Product / Services

  1. Testing Equipment 10 Products available
  2. Industrial Machinery 9 Products available
  3. Weighing Scales & Measuring Tapes 3 Products / Services available

  4. Dynamometer

    1 Products available

  5. Microscope

    1 Products available

  6. Surface Finishing Machines

    1 Products available

  7. Electrical & Electronic Testing Devices

    1 Products available

  8. Testing Equipments

    1 Products available

  9. Calibration Services

    1 Services available

  10. Computer Printers

    1 Products available
  11. Others Products / Services 7 Products / Services available

Weighing Scales & Measuring Tapes

Our offered Product range includes Dynamic Balancing Machine, Dynamic Balancing Machines, Vertical Balancing Machine and Balancing Machines.

Dynamic Balancing Machine

Dynamic Balancing Machine
Machines Model HDM are horizontal type universal hard bearing balancing machines provided with Microprocessor based measuring panel HDM-8500 for balancing different shapes of rotors like rotors of electrical machines, crankshafts, cylinders, Gas Compressors, flywheels, turbine rotors, rotors of centrifugal pumps and any other type of rotors of rotating machines. These machines features a very simple operation. The working cycle is fully automatic. From safety point of view a double press push button starts machine, measures and stores the unbalance values on DPMs for two planes simultaneously and stops machine ( with brake if machine is provided with electrical breaking facility.) The measuring cycle general is less than 10 seconds for normal rotors, which can be accelerated within 5 seconds.
View Complete Details
Ask Latest Price & Details
Dynamic Balancing Machines

Dynamic Balancing Machines
with Microprocessor Based Measuring Panel ( Hard Bearing Model - HDCM )
Machines model HDCM are belt driven horizontal type photo scanning Universal Hard Bearing Balancing Machine, provided with microprocessor based measuring panel HDCM 8500 suitable for balancing different shapes of rotors, of electrical machines, Cylinders, fly wheel, rotor of centrifugal pumps and other type of rotating machines.
These machines are very simple in design. No drive coupling / adaptor etc. required to connect to the rotor to be balanced. It has following advantages -
Cost saving on manufacturing of precision adaptor to connect drive coupling to rotor.
Any rotor can be balanced without losing time in manufacturing of adaptor.
The balancing accuracy of rotor not disturbed due to unbalance in drive coupling / adaptor.
Belt drive machine are more accurate (about 5 times) as compared to end drive machine.

The machines features a very simple operation. The working cycle is fully automatic. From safety point of view a double press push button starts machine, Measures and stores the unbalance values on DPMs for two Plane simultaneously and stops machine. Key board facility provided in measuring panel for correct data feeding of rotor with 1 digit accuracy for its dimensions like A, B, C, R1 & R2. Tolerance limits of both correction planes i.e. +11 & +12 can be feed so that when rotor is balanced within the limits respective LEDs glow up, indicating no further correction necessary. For other details please refer features of measuring panel HDCM-8500

Standard Features:
Digital display for unbalance indication
Amount and angle for unbalance for both planes displayed on separate DPMs. Hence linear accuracy is very goos as compared to analog meter+digit for amount and+degree for angle.
Digital display for RPM indication
A DPM is provided to indicate balancing speed continuously as a standard feature.
Auto Stop
No necessity to stop machine once started. It stops automatically after stabilization of unbalance results.
Simultaneous Indication
Amount and angle of unbalance in both planes displayed simultaneously and remains displayed (stored ) till next run. This totally eliminates operation of plane selector and reduces additional time for stabilization of readings in other plane.
Key-Board
Data of rotor dimensions and balancing tolerance i.e. values of A, B, C, R1, R2, t11, t12 are fed by key operation. Hence accuracy of data feedings accurate up to 1 digit.
Tolerance Indicators
Separate LEDs are provided for both planes which glow when unbalance is reduced within balancing tolerance.
Auto Range
Depending upon whether unbalance amount is more or less a respective course or fine range gets automatically selected till rotor gets balanced within tolerance limits, Multiplier operation is totally eliminated.
Data store
Data is provided with 'Self check' mode which checks proper functioning of digital display. LED's is cycle operation. This helps immediate fault detection.
Self Check
Panel is provided with self-check mode which checks proper functioning of digital displays, LEDs is cyclic operation (optional). This helps immediate fault detection.
Additional Featureson demand :
Printer :
A matrix printer can be connected through FIE software. It shows runs till rotor is balanced within balancing tolerance.
Component Indication :
FIE software specially developed with 3-99 component indication, is suitable for balancing of rotor with fixed locations for balancing correction.
Unbalance Correction :
Drill attachment 8mm capacity portable drill with supporting overhead railing.
Separate drilling attachment 19mm. Capacity with a vertical drilling head , manual.
Portable type reveting hammer (piston type) speed 1800 blows/minute, capacity 6mm in a aluminum suspected from top with rail.
Tangential belt drive, in addition to standard (suitable for a particular type of rotor for production balancing)
Longitudinal movement of right hand pedestal by chain & sprocket attachment.
The balancing speed depends upon selection of the rotor diameter, where drive is to be given and the motor pulley diameter.
All the machines above operate on mains supply of 400 to 440 V, 3, 50 cycles.
Due to constant R & D, specifications and features are subject to change without notice. The dimensions given above are approximate.

Models Unit HDCM-10 HDCM-30 HDCM-50 HDCM-100 HDCM-300
Weight of Rotors kg 0.2-10 0.3-30 0.5-50 1-100 3-300
Max. wt. on each pedestal kg 7.5 22.5 30 75 180
Max. diameter of rotor mm 250 500 500 800 1000
Max. distance between bearings mm 300 1200 1200 1200 2100
Min. distance between bearings ( drive outside pedestal ) mm 20 50 50 50 150
Shaft diameter mm 5-50 5-50 5-50 15-80 20-120
* Balancing speed range ( n ) RPM 750-3000 500-2000 500-2000 400-1600 300-1500
Power of drive motor HP 0.33 0.75 0.75 1.5 3
Acceleration capability ( gs2n2 ) kgm2n2 0.29x106 0.37x106 0.37x106 0.88x106 3.9x106
Min. Unbalance mass measured g 0.01 0.1 0.1 0.1 0.1
Max. Unbalance mass measured kg 0.4 4 4 4 4
Unbalanced reduction ratio % 95 95 95 95 95
Min. Achievable unbalance 
per rotor wt. ( For max. rotor wt. ) 		gmm / kg or micron. 0.2 0.2 0.2 0.2 0.2

View Complete Details
Ask Latest Price & Details
Vertical Balancing Machine

Vertical Balancing Machine
Machines Model HDVTM are Vertical type single plane hard Bearing Balancing Machine provided with Microprocessor based measuring panel HDVM 8500 for balancing Disc shaped Rotors such as Clutch Plates, Fan Blades , Fly Wheels, Magnetos, Grinding Wheels, Impellers etc. Where as HDVTM are vertical type two plane Hard Bearing Machines provided with Microprocessor based measuring panel HDVTM 8500 for balancing spinning pots, Spinning spindles etc.
Both type Machines feature a very simple operation. The working cycle is fully automatic From safety point of view a double press push button starts machine, measures, and stores the unbalanced values on DPMS and stops machine.
Keyboard facility provided on measuring panel for correct Data feeding of Rotor with one digit accuracy for its dimensions like RAD, +1, for single plane & w, d, r1, r2, +11, +12 for two plane machines. When Rotor is balanced within the limits respective LEDs glow up, indicating no further correction is necessary. For other details please refer standard features of measuring panel HDVM and HDVTM.
Both type of machines are provided with electronic companion software to comensate the unbalance effect due eccentricity between rotating ( Spindle ) axis & adaptor (Rotor) axis.
Standard Features :
A. Standard Features of 'HDVM-8500 & HDVTM-8500' :
1) Digital display for unbalance indication :
Amount and angle of unbalance for both planes displayed on separate DPMs for HDVTM M/c. Hence linear accuracy is very good as compared to analog meter. Accuracy + 1 digit for amount and + 1 degree for angle.
2) Digital display for RPM indication :
A DPM is provided to indicate balancing speed continuously as a standard feature.
3) Auto Stop :
No necessary to stop machine once started. It stops automatically after stabilization of unbalance results.
4) Simultaneous Indication :
Amount and angle of unbalance in both planes displayed simultaneously and remains displayed (stored ) till next run. This totally eliminates operation of plane selector and reduces additional time for stabilization of readings in other plane.
5) Key-Board :
Data of rotor dimensions and balancing tolerance i.e. values of A, B, C, R1, R2, tl1, tl2 are fed by key operation. Hence accuracy of data feeding is accurate up to 1 digit.
6) Tolerance Indicators :
Separate LEDs are provided for both planes which glow when unbalance is reduced within balancing tolerance.
7) Auto Range :
Depending upon whether unbalance amount is more or less a respective course or fine range gets automatically selected till rotor gets balanced within tolerance limits, Multiplier operation is totally eliminated.
8) Data store :
Data of various rotors can be stored against respective rotor type nos. Hence no need of measuring of rotor dimensions or rotor data feeding when repeat balancing operation required. Just call rotor type no. and machine is ready for balancing.
9) Self Check :
Panel is provided with self-check mode which checks proper functioning of digital displays, LEDs is cyclic operation. This helps immediate fault detection.
B. Additional Features on demand for Unbalance correction (Optional) :
1. Vertical drilling attachment with drilling thrust compensation.
2. Horizontal drilling attachment with drilling thrust compensation.
3. Welding attachment.
4. Any other attachment as per customers requirement.
C. Printer :
A matrix printer can be connected through available FIE software.
D. Compensation Indication :

FIE software specially developed with 3 99 component indication, is suitable for balancing of rotor with fixed locations for balancing correction.
Technical Specifications :

Vertical Hard Bearing Balancing Single / Two Plane Dynamic Balancing Machine

Models Unit HDVM 10 HDVM 30 HDVM 50 HDVM 100 HDVM 300 HDVTM 5 HDVTM 10
Weight of Roters kg 0.5-10 1-30 1.5-50 3-100 10-300 0.2-5 0.5-10
Max. Diameter of Rotor mm. 400 500 500 600 1000 300 300
* Balancing Speed ( n ) RPM 1000 750 600 500 350 1200 1000
Power of Drive Motor HP 0.75 1.5 1.5 3 7.5 0.33 0.75
Acceleration Capability ( Gd2 N2 ) kgm2 n2 0.37x106 0.88x106 0.88x106 3.9x106 14.12x106 0.29x106 0.37x106
Min. Unbalance Mass Measured g 0.1 0.1 0.1 0.1 1 0.01 0.01
Max. Unbalance Mass Measured kg 4 4 4 4 4 0.2 0.2
Unbalance reduction Ratio % 95 95 95 95 95 95 95
Min. Achievable Unbalance per
Rotor wt. ( For max. Rotor wt. ) 		micronsor gmm/kg 5 5 5 5 5 5 5

View Complete Details
Ask Latest Price & Details
Tell Us What are you looking for? Will call you back

Contact Us

  • Sachin Purohit (MTMS ENGINEERS PRIVATE LIMITED (formerly Known As Material Testing Mac)
  • Narsinh Residency, Flat No. B-4, 1st Floor, S. No. 81/2-A-1-A Main Road, New Sangvi, Sanghvi, Pune, Maharashtra - 411027
  • Share us via
    Linkedin pinterest

  • Found Something Wrong with this Listing? Report Here.

View Contact No.