Plastic Granules #651273

We are offering pib masterbatch pt60. polyfill pt-60-pib masterbatch is a average molecular poly isobutylene based masterbatch based on polyolefins, used in lldpe ldpe self adhesive stretch film, cling film, & wrap film (either blown film or cast film) and it is available in-granule-form. pib master batch pt60 is very easy to handle as against the direct dosing of pib liquid which is very difficult & tedious to handle due to high viscosity. Our pib master batch distributes very uniformly over the entire film imparting the strength & tackiness properties to the film with self adhesive properties. And this property of the film helps to bind the packages together with proper grip. In multi-layer films, pib master batch , is used only in one layer , the upper layer and the adding ratio is determined by the film thickness and on the layer to be used. addition-levels cling films made from our pib master batch are most economical and the quality of the film coverage increases on stretching. The loading of pib master batch varies from 3% to 8% depending upon the type of the film plant (blown or cast-line)--installed. we suggest the following addition level based on the test results from outdoor weathering tests and from practical experience : blownfilmapplication 3----5% castfilmapplication 1----2% the above dosages are for guidance only. Actual condition may vary from film to film, process to process and also upon the thickness of the film and its specific-uses. material--mixing to get the best results in case of extrusion, it is advisable to mix the material thoroughly before feeding in a hopper. applications stretchcling---wrap----film storage there should be no problems in storing of pt-60-pib. The storage life is six months of pt-60-pib at 25c, although not very sensitive to heat and humidity , proper storage will prolong the storage life of the product.

We are offering tio2 milky white masterbatch. introduction polyfill tio2 white masterbatch pt2002, 65% loaded, is manufactured by blending high quality tio2 powder in polyethylene of high melt flow index in presence of additives like antioxidant, dispersing agent and dessiccant. pt2002 has been specially designed for poly film, injection moulding and extrusion process. special characteristics pt2002, tio2 white masterbatch has been designed to impart the following special properties excellent brightnessexcellent dispersioneasy processingresistance to yellowing technical characteristics properties test method unit valuesmfi astm d 1238 g10 min 10-20moisture content ppil ppm

We are offering ppa masterbatch.Advantage pt3001 can offer performance and cost advantage. It exhibits exceptional commercial utility in low melt index film grade lldpe , hdpe, hmhdpe. It is especially effective in polyolefin resins containing talc and silica based anti blocking agents, tio2 based pigment and other inorganic additives. It can also be used at low levels to reduce extruder die built up when processing lldpe, eva and other polyolefin resins.pt3001 is designed for use at a very low level to improve processing of thermoplastics. It does not alter or detract from the good physical properties associated with high strength plastic.

We are offering tio2 white masterbatch.Special characteristics pt2002, tio2 white masterbatch has been designed to impart the following special properties excellent brightnessexcellent dispersioneasy processingresistance to yellowing

We are offering slip additive masterbatch.Advantages:- reduces frictional resistance between two plastic films and between plastic and metal parts.pt-3004 makes processing more efficient with higher productivity and improved quality.in polyolefin film production, pt-3004 facilitates increased line speed in manufacturing process and enhances packaging machine operation due to reduced cof.ensures good handling properties in automatic packaging machines.

Using Antistatic Masterbatch PT3002 will reduce or even eliminate the problems caused by high surface resistivity. These problems include : Increase handling problems during transport, storage and packing.Dust contamination, affecting both, appearance and performance of end products.Risk of electrical shocks to employees working at the machines.Risk of electrical discharge causing fire or explosion.

We are offering anti static masterbatch. introduction polyfill antistatic masterbatch, pt3002 is a surface property modifier, which now-a-days finds extensive use by plastics processor, to reduce and control the static charges developed on the surface of plastic parts having large surfaces like film, fibres etc as spark discharge formed by static charges can produce serious accidents. Plastics, particularly sensitive to static build up polyolefins, nylon, polyesters, urethanes, cellulosics, acrylics etc. polyfill anti static masterbatch, b#pt3002 is based on ethoxy amine, using lldpe as a carrier resin, compounded in most modern extrusion equipment, using state of art technology. characteristics accumulation of electrostatic charges on plastic surfaces can occur during processing and at various handling points all the way to consumer, results in dust attraction which limits its application for aesthetic and hygienic use, besides seriously affecting its organo-leptic properties. Static charges are dissipated by increasing the surface conductivity of products either by use of internal or external antistatic agents which form conductive ionic layer. External antistatic agents tend to provide only short term protection since they are subjected to the removal by wear or exposure. Internal antistatic agents tend to be more permanent since most are hydrophilic and migrate to the surface if the ionic layer is wiped away from time to time. mode of action pt 3002 antistatic masterbatch, an internal antistatic agent acts in two ways : builds up conductive path to bring charged particles into contact. as a lubricant or mould- release agent in the post extrusion process. pt3002 is incorporated into the polymer during the extrusion process. Upon extrusion, the additive masterbatch migrates to the surface of the film because of its definite incompatibility with the polymer where the additive masterbatch builds up a uniform layer on the film product surface and prevents the building up of static electricity. It also reduces surface resistivity by migrating to the surface and absorbing moisture from the air. benefits using antistatic masterbatch pt3002 will reduce or even eliminate the problems caused by high surface resistivity. These problems include : increase handling problems during transport, storage and packing. dust contamination, affecting both, appearance and performance of end products. risk of electrical shocks to employees working at the machines. risk of electrical discharge causing fire or explosion. applications polyolefins (hdpe, hmhdpe, pp, lldpe, ldpe) packaging commodities such as films, wrapping sheets etc. plastic packaging for explosives. pvc decorating film for furnitures. plastic conveyor belts in mines. electronic switches. plastic flooring in operating rooms to prevent spark discharge during machinery operation. typical properties (data not for specification purpose)form granularcolour clearactive ingredients - antistatic 10%particle size apprx 10 meshinorganic additives 3%polymer - lldpe (50 mfi) 87% addition level 0.5 to 2%, depends on specific end use applications and the thickness of the finished products. packaging the material is packed in pe lined, moisture proof heavy duty pp bag in 25 kg pack.

We are offering slip masterbatch. introduction polyfill slip additive masterbatch, pt3004 is the material which when added to the polymer, while processing into flat profiles like film, sheet etc, reduces the coefficient of friction (cof) of the surfaces. It is particularly used while manufacturing film for packaging application where film to metal as well as film to film friction is required to be controlled. characteristicsthe chemical nature of slip agents is such that they are high molecular weight and are partially compatible with the basic resin. Slip additive masterbatch pt3004, when incorporated into the polymer at the time of processing, migrate to the surface of the extruded / moulding and provide a mono-molecular layer which in turn reduces the cof. pt 3004 slip additive masterbatch is based on highly purified erucamide in lldpe carrier resin and compounded in most modern extrusion equipment using state of art technology. The slip additives chosen are stable up to 220* c and recommended for use where high temperature processing is required. benefitspt3004 makes processing more efficient with higher productivity and improved quality. reduces frictional resistance between two plastic films and between plastic and metal parts. in polyolefin film production, pt3004 facilitates increased line speed in manufacturing process and enhances packaging machine operation due to reduced cof. ensures good handling properties in automatic packaging machines. applicationsslip additive masterbatch pt3004 is applicable to all processors from industries like packaging (monolayer & multilayer flexible packaging film), moulding, agricultural films etc. slip additive masterbatch is recommended for use as demoulding agents in injection moulding application. dosage 1- 5% depending on the end use application. for low slip - 12%, for medium slip - 23%, for high slip 4-5% packing the material is packed in pe lined, moisture proof heavy duty pp bag in 25 kg pack.