Ms. Perma Construction Aids Pvt. Ltd.

Mulund West, Mumbai, Maharashtra

Perma R - Poxy is a two component thixotropic epoxy resin based coloured joint. Perma R - Poxy is used for filling joints in between tiles or stone. Perma R - Poxy provides for aesthetic germ proof, chemical and hard wearing joints, resistant to a wide range of spillages and chemical attacks. Part A consists of a thick colored paste consisting of epoxy resin, graded aggregates, pigments and additives. Part B consists of a soft paste consisting of a mixture of graded fillers and catalyst. Primary Uses : For grouting residential and industrial floor joints where hygiene control, damp & wet conditions are experienced along with chemical resistant properties. Typical Applications : Perma R - Poxy is designed for use in floor tile, wall tile and stone joints for interior as a jointing material and exterior application for joints width varying between 2 mm to 15 mm. The area of application are for floor and wall tiles in bathroom and shower areas, kitchen counter tops, terrace and balconies, chemical plant, hospitals, refineries, garages, laboratories, warehouses, bakeries, swimming pools etc. Coverage : 1 kg of Perma R - Poxy shall cover an area of 20 sq. ft. for joint width of 8 mm and for tile size 12� x12� Properties :

• Appearance : Part A: Coloured Paste, Part B: Soft Paste
• Density : 1600 kg/m3
• Specific Gravity of Mix : 1.60 Kg/L
• Pot Life : 60 minutes @25^o C
• Application Temperature : 2^o C to 30^o C
• Water Absorption : NIL
• Touch Free Time : 7 hours @25^o C
• Final Cure : 7 days @25^o C
• Temperature Resistance : up to 70^o C
• Tensile Adhesion of Epoxy Grout : >4.5KN
• Shear Adhesion Strength : I n i t i a l > 2 N / M ² ( E N2003) After immersion in water >2N/ M²
• Abrasion Resistance : 250Mm3 (EN12808-2)
• Flexural Strength : 30N/mm² (EN 12808-3)
• Compressive Strength : In excess of 45N/mm² (EN 12808-3)

Advantages :

• High compressive, flexural and tensile strength in excess of concrete.
• Chemical resistant and waterproof.
• Hygienic and non-dusting.
• Easy to use and easy to clean.
• Uniform coloring.
• Stain free.
• Supplied in pre-measured units.
• Does not support bacterial growth

Packing : Perma R - Poxy is supplied in 1 kg and 5 kg pack size. Shelf Life : 12 months from the date of manufacture Mixing Ratio : Mix Part A two parts by weight to Part B one part by weight with the help of a slow speed drill equipment to a lump free homogeneous consistency. Spread the material with a spatula or squeeze float into the joints. Direction for Use :

• Preparation of the area : Make sure that the tiles or the stone joint operation is taken up atleast 72 hrs after the tiles are laid. The joints shall be dry and free from deleterious materials.
• Application : Apply masking tape where porosity in tiles or stones is encountered. If not, clean the joints with a blower and apply the grout gel using a squeezy blade. Clean the grouted area with a squeezy sponge dipped in water and finishes the surface. Allow the grout to dry through air curing.

Perma Inject Dyc Resin-Catalyst is a polyurethane injection grouting system. It consist of two component one being pre polymer resin and the other being a catalyst These two components are mixed together and injected into the concrete or Ree structure using a single component pump whether manual or motorized. Perma Inject Dye when injected into the concrete forms a flexible foam when it comes in contact with water or moisture. This foam effectively stops leakages from the structures. Advantages :

• Perma Inject Dye seals leakages in all difficult situations such as basements, tunnels and heavily leaking massive structures
• Perma Inject Dye is free from solvents and fillers. It is resistant to hydrolysis and is suitable for use In potable water tanks
• The product is supplied as two components the reactor/catalyst can be adjusted from six to ten percent to allow on site adjustment of gel time
• Perma Inject Dye stops the leakage then and there only Instantly, after Injection, there Is no waiting period to wait far curing time etc

Packing : Perma inject dyc is supplied in packing of 25 kg for pre polymer resin and the catalyst in 2.5 ltr packs and 10kg for pre polymer resin and the catalyst in 1 ltr packs

Perma Inject Stc Resin-Catalyst is a polyurethane injection grooting system. It consist of two component one being is pre polymer resin and the other being a catalyst These two components are mixed together and injected into the concrete or RCC structure using a, single component pump whether manual or .motorized. Penna Inject STC when injected into the concrete forms a semi-rigid.and semi flexible foam when it comes in contact 'with water or moisture.This foam effectively stops leakages from the structures. Advantages :

• Perma Inject STC seals leakages in all difficult situations such, as basements, tunnels and' heavily leaking massive structures
• Perma Inject STC is free from solvents : and fillers. It is resistant to hydrolysis is and is suitable for use in potable water tanks
• The product is supplied as two components the reactor/catalyst can be adjusted from six to ten percent to allow on site adjustment of gel time
• Perma inject STC stops the leakage then and there only instantly, after injection. there is no waiting period to wait for curing etc.

Packing : Perma inject STC is supplied in packing of 25 kg for pre polymer resin and the catalyst in 2.5 ltr packs and 10 kg for pre polymer resin and the catalyst in 1 ltr packs

tpe tape for waterproofing open joints in structures

thermoplastic elastomer based tape available in suitable lengths for covering expansion joints, isolation joints, weak construction joints and joints between two dissimilar building materials such as concrete and stone work or concrete and steel/pvc pipes etc.

failed expansion joints where in the sealant has failed either in or cohesion or adhesion, cause severe leakage problem in the buildings and these leakages start corroding reinforcing steel bringing down the life of the structure drastically. Similar phenomenon is observed in the joints of dissimilar building materials such as joints of concrete with steel/pvc pipes, junctions of rcc and stone slabs/blocks, many such junctions in sewage and water treatment plants, building roofs etc. Perma expa tape offers a permanent solution to these nagging problems. It not only water proofs these weak areas but also helps in maintaining their aesthetics and life of the structure.

Perma Waterproof Butyl Tape SF-50 Is a single sided butyl rubber adhesive tape which is used for water proofing all joints in construction Industry, during construction and post construction. Primary Uses :

• Perma Waterproof Butyl Tape SF-50 is used for covering all cracks, construction joints, bends and corners and joints of non homogeneous materials before application of waterproof membranes such as Penna Guard or Penna Eazee Coat
•  Is used for joint sealing of the metallic and non metallic roofing such as aluminum, zinc asbestos sheeting. 3. Penna Butyl Tape'SF5O can be used for sealing all joints in timber framed houses
• It is used for sealing all the comer joints and the joints between the horizontal and vertical RCC surfaces of the sunken slabs of to nets and bathrooms after water proofing. It is also used for covering of all cutouts and pipe joints in the walls
• This tape is used for covering the insulated air conditioning ducts

Advantages :

• Perma Waterproof Butyl Tape SF-50 Is resistant to hot and cold temperatures. It with stands 90^oC without yielding
• Perma Waterproof Butyl Tape SF-50 Is totally waterproof
• It has good adhesion to all types of surfaces and can be planted over.

Packing :

• 50mm x 20mtr - 1roll (minimum pkg 8 roll)
• 100mm x 20mtr - 1roll (minimum pkg 4 roll).

Due to our keenness to serve the people in every possible way, we have obtained a distinguished position in the market. We have emerged as a notable name in manufacturing and supplying premium quality construction waterproofing materials fiber mesh for our clients. The offered glass fiber mesh construction waterproofing is a fabric made up of alkali-resistant glass fiber and is widely used in plasters, weatherproofing and waterproofing membranes to control the cracks. The offered fiberglass mesh for waterproofing is extremely light in weight, tough, flexible, high in tensile strength and easy to work with. You can rely on us for construction waterproofing materials fiber mesh that you can get at a market leading price. Additionally, we ensure the on-time delivery of your consignment.

Perma Heavy Duty Mortar (HDM) is a three component high performance epoxy resin based concrete that provides a rough looking extremely strong bedding mortar or screed mortar to industrial floors. The Perma Heavy Duty Mortar (HDM) is also used in heavy duty repairs of dams, tunnels, spillways, bridge girders, etc. We manufacture, export and supply the excellent quality Perma Heavy Duty Mortar (HDM) around the world. Clients can avail the Perma Heavy Duty Mortar (HDM) at very economical prices.

 

Advanteges :

• Abrasion resistant and hard wearing.
• Slip resistant.
• High Strength.
• Easy to handle.
• Resistant to chemicals and aggressive substance.

Three Component Heavy Duty Epoxy Concrete for Industrial Floors and Heavy Duty Repairs of Dams, Tunnels and BridgesPerma Master Floor (HDM) is a Three Component high performance epoxy resin based concrete that provides a rough looking extremely strong bedding mortar or screed mortar to industrial floors. This product is also used in heavy duty repairs of dams, tunnels, spillways, bridge girders etc.


Directions for Use

• Surface preparation - As with all epoxy resin systems, surface preparation is of prime importance. For concrete surfaces, remove all grease, oil, dust, laitance etc. Ensure substrate to receive the screed is sound, cut back to sound surface wherever necessary.
• Primings - Remove dust and ensure that all the surface is dry. Prime with Perma Master Prime-CN or Perma Master Bond.
• Mixing - Do not split packs or alter the components in any way. Mix in a suitable mechanical pan type resin mixer. Thoroughly mix both liquid components together prior to the addition of the aggregate component. Remix until the aggregate is completely dispersed.
• Application - Spread the mixed Perma Master Floor (HDM) onto the primed surface the primer must still be fully tacky. Rake or spread out to the thickness required, compact and finish with a steel trowel.
• Perma Master Floor (HDM) shall be laid on suitable prepared surfaces where indicated. Perma Master Floor (HDM) is manufactured to the following specifications.

Perma Master Patch - NSF is a high performance epoxy resin based structural repair system that provides a smooth finish to the repaired areas. Perma Master Patch - NS is a two component product based on epoxy base and Hardener which needs only on site addition of quartz ball Milli powder or silica flour to produce a non slump paste which is used for repairing beam and column edges and spelled/Honeycombed concrete. Advantages :

• Very strong repair material
• The repair mortar paste is non slump
• Repaired areas can be put to use faster

Packing : Perma Master Patch - NS is supplied in 250 grams and 1 kg pre weighed units

Perma Epoxy 100 - EG is a two component epoxy suitable for injecting into the porous concrete to consolidate the structural elements. Primary Uses :

• Perma Epoxy 100 - EG is developed as a low viscosity easy flowing epoxy resin system which travels easily in the body of concrete and consolidates all loose particles
• Perma Epoxy 100 - EG is used for consolidating the concrete mass in weak concrete structures
• Perma Epoxy 100 - EG is used for preventing water contact of reinforcement in structures which hold water on one side
• Perma Epoxy 100 - EG is used for water proofing leaky porous concrete structures

Advantages :

• Perma Epoxy 100 - EG is a low viscosity product hence flows freely even into the finest cracks and pores of concrete
• Perma Epoxy 100 - EG is fast setting hence bleeding wastage of the product are minimized
• Perma Epoxy 100 - EG is supplied in pre weighed containers in the proportion of mixing hence convenient to use

Packing : Perma Epoxy 100 - EG base & reactors are supplied in 1kg, 40kg packing

Perma Master Coat is an aesthetic and protective epoxy resin coating which has been specifically developed to meet the 'In service' protection of concrete, metal etc. The product is supplied as two-pack system comprising of pigmented base and hardener. It requires only on site mixing to produce an easily applied decorative and chemical resistant finish. Perma Master Coat coating will not support the growth of bacteria. Primary Uses :For the external and internal protection of concrete or metal tanks containing drinking water, oils, consumable liquids.etc. Best used as floor and wall coating. It water proofs the surface son which it is coated, Used as an impervious, resilien and chemical resistant floor or wall coating in food processing plants, breweries, canning and bottling factories and general water proofing. Used as a protective and decorative coating in laboratories, abattoirs etc. Advantages :

• Durable
• Solvent free
• Non-toxic
• High build coating
• Waterproof
• Chemical resistant
• Easily applied by brush or roller

Packing : 1kg, 40kg and bulk

Perma Master Fill - EP is a two component filled epoxy system which needs mixing of the two components thoroughly to produce a knifing putty. Perma Master Fill - EP is suitable for filling fine cracks depressions on the surface and repairing honey combs in the concrete to make it fair faced and suitable for subsequent coating. Perma Master Fill - EP is solvent free and chemical resistant. Primary Uses :

• For repairing surface blemishes
• For filling cracks
• For smoothing concrete as well as metal surfaces before painting

Advantages :

• Non toxic can be mixed by hand
• Durable
• Solvent free
• Easy to use. Requires two components to be mixed in equal proportions
• Chemical resistant
• Easily applied by putty blades or metal floats
• Non slump can be easily applied on vertical surfaces
• Reduces usage of subsequent coatings
• Cure without shrinkage
• Color matched to parent concrete

Packing : 1 kg

Porosity of concrete surfaces, moisture and the alkalinity of the concrete surface makes it difficult for the epoxy products to bind with the concrete bases effectively. to get over these problems an effective epoxy primer is made use of. Perma Master Prime - CN is a two component product based on non solvented epoxy base and epoxy hardner. Perma Master Prime - CN binds the epoxy products firmly to the cementitious bases. Primary Uses :To bind epoxy mortars and flooring products to the concrete base taking care of the porosity of the base and mobilizing the particles of the mortars into the crevices and holes in the base. Advantages :

• Perma Master Prime - CN thoroughly wets the concrete surface and mobilizes the particles of the epoxy products effectively on the concrete surfaces and makes it easier for epoxy products to bind with the concrete effectively
• Perma Master Prime - CN being moisture tolerant makes the priming easy, There is no need to blow torch the surfaces to make them bone dry a reasonable dry surface is good enough
• Perma Master Prime - CN is resistant to alkalies hence there is no need for the cumber some process of acid itching the surface

Packing : Perma Master Prime - CN is supplied in 1 kg pre weighted units

Epoxy Based Non Slump Structural Repair SystemPerma Master Patch-NS is a high performance epoxy resin based structural repair system that provides a smooth finish to the repaired areas. Perma Master Patch —NS is a two component product based on epoxy Base and Hardener which needs only on site addition of quartz ball Mill powder or silica flour to produce a non slump paste which is used for repairing beam and column edges and spalled / honeycombed concrete.

Advantages

• Very strong repair material.
• The repair mortar paste is non slump.
• Repaired areas can be put to use faster.

Directions for Use

• Surface Preparation - As with all epoxy resin systems, surface preparation is of prime importance. For concrete surfaces, remove all grease, oil, dust, laitance etc. Ensure substrate to receive the screed is sound, cut back to sound surface wherever necessary.
• Priming - Remove dust and ensure the surface is dry. Prime with Perma Master Prime-CN / Perma Master Bond.
• Mixing - Mix in a suitable pan type of a mixer consisting of 720 gms Base and 280 gms of Reactor components and to this add and mix 2 Kg quartz ball mill powder and quartz sand 30/80 in 1:1 proportion. Mix in a suitable pan type of a mixer.
• Application - Perma Master Patch-NS mortar thus prepared looks like a stiff paste. Apply the mixed Master Patch-NS mortar onto the primed surface while it is still tacky, and feather edge it to restore the original shape of the structural member.

Packing

• Perma Master Patch-NS is available in 250 gms and 1 kg pre weighed units and in bulk.

We are offering perma master prime, porosity of concrete surfaces, moisture and the alkalinity of the concrete surface makes it difficult for the epoxy products to bind with the concrete bases effectively. To get over these problems an effective epoxy primer is made use of. perma master prime - cn is a two component product based on non solvented epoxy base and epoxy hardner. Perma master prime - cn binds the epoxy products firmly to the cementitious bases. primary uses :to bind epoxy mortars and flooring products to the concrete base taking care of the porosity of the base and mobilizing the particles of the mortars into the crevices and holes in the base. advantages :

• perma master prime - cn thoroughly wets the concrete surface and mobilizes the particles of the epoxy products effectively on the concrete surfaces and makes it easier for epoxy products to bind with the concrete effectively
• perma master prime - cn being moisture tolerant makes the priming easy, there is no need to blow torch the surfaces to make them bone dry a reasonable dry surface is good enough
• perma master prime - cn is resistant to alkalies hence there is no need for the cumber some process of acid itching the surface

packing : perma master prime - cn is supplied in 1 kg pre weighted units download

Perma Grout - 500 is a fine free flowing grey powder with a wide range of grouting applications, mainly to produce expansive grouting slurries, mortars and concrete. Primary Uses :Perma Grout - 500 is and a mixture for grouting Cement slurries, grouting mortars and non shrink concrete. Perma Grout- 500 is a free flowing grey powder especially designed for cable duct grouting In post tensioned bridge grinders. Injection grouting of porous concrete In structural rehabilitation work sand in in fill mortars in filling and sealing cut outs, recesses and foundation pockets. Packing : 500gms and 10kg sack

Perma Grout - 500 is a fine free flowing grey powder with a wide range of grouting applications, mainly to produce expansive grouting slurries, mortars and concrete. Primary Uses : Perma Grout - 500 is and a mixture for grouting Cement slurries, grouting mortars and non shrink concrete. Perma Grout- 500 is a free flowing grey powder especially designed for cable duct grouting In post tensioned bridge grinders. Injection grouting of porous concrete In structural rehabilitation work sand in in fill mortars in filling and sealing cut outs, recesses and foundation pockets. Packing : 500gms and 10kg sack

Perma R-Poxy is designed for use in floor tile, wall tile and stone joints for interior as a jointing material and exterior application for joints width varying between 2 mm to 15 mm. The areas of application are for floor and wall tiles in bathroom and shower areas, kitchen counter tops, terrace and balconies, chemical plants, hospitals, refineries, garages, laboratories, warehouses, bakeries, swimming pools etc. Preparation of the area: Make sure that the tiles or the stone joint operation is taken up atleast 72 hrs after the tiles are laid. The joints shall be dry and free from deleterious materials. Application: Apply masking tape where porosity in tiles or stones is encountered. If not, clean the joints with a blower and apply the grout gel using a squeezy blade. Clean the grouted area with a squeezy sponge dipped in water and finish the surface. Allow the grout to dry through air curing.

Perma R-Tone Filler-WD is a three component product consisting of water dispersible epoxy base and reactor and tiller. It only needs on site mixing of the three ingredients to get an uniform consistency smooth paste which is used for filling tile joints. It is also used for filling the joints between stones marbles cut stones etc. Conventional cement based joint tillers are not strong enough, they have the tendency of promoting the growth of bacterial colonies and the epoxy based tile joint fillers do not satisfy the hygienic standards laid down by the food and the pharmaceutical industry. Perma R-Tone Filler-WD is available in SELECTED shades, giving an ample choice of creating the desired pattern with matching or contrast shade of R-Tone Filler -WD with the shade of tiles. Primary Uses :Perma R-Tone Filler-WD is used for filling tile joints in areas where utmost hygienic conditions are desired. It is recommended in joint filling of tiles in hospitals, operation theaters, pharmaceutical industry and food processing industry Advantages :

• Available in selected shades
• Joints become strong and hygienic
• No staining of the joints
• Makes the tiled area germ proof

Packing : Perma R-Tone Filler-WD is available in 1 Kg. and in 10 kg packing.

High build polymer based paint for road marking.

 

SPECIFICATION : Perma Road Marking Paint is a water based coating for marking on roads and concrete floors. The product is based on high performance polymers specially developed to stand heavy traffic and adhesion to most flooring substrates. The product is available in yellow, black and white colours.

 

PRIMARY USES : Perma Road Marking Paint is designed for marking on the bituminous asphalt roads, concrete floors, concrete sports surfaces and pavers. The product is suitable for marking in vehicle parking lots, garages, workshops, factory floors etc.

 

ADVANTAGES

• Perma Road Marking Paint is water based hence easy to apply.

• Road marking of small areas is convenient as obtaining thermoplastic coating equipment is not feasible on small jobs.

• Perma Road Marking Paint does not need any primer. It can be applied straight from the can itself.

• Applied areas can be easily recoated after ageing of the first coated layer.

 

DIRECTIONS FOR USE : Clean the surface to be marked by washing and blowing compressed air. Apply masking tape around the areas to be marked. Apply two coats of Perma Road Marking Paint in liberal coats, the second coat being applied just when the first coat dries. Remove the masking tape when the second coat dries.

 

PACKING : Perma Road Marking Paint is available in 1Kg, 10Kg and 20Kg Packs.

 

SHELF LIFE : Perma Road Marking Paint has a shelf life of 12 months from the date of manufacture.

Perma Master Floor - HD is a high performances epoxy resin based concrete that provides a rough looking extremely strong bedding mortar or screed mortar to industrial floors. Advantages :

• Abrasion resistant and hard wearing
• Slip resistant
• High strength
• Easy to handle
• Resistant to chemical and aggressive substances

Packing : Perma Master Floor - HD is supplied in 10 kg pre weighed units and in bulk.

We are highly engaged in providing best quality polyurethane-based waterproofing for our buyers as per their requirements. We are one of the reliable firms, involved in offering a wide gamut of polyurethane based waterproofing products for our clients. The provided waterproofing products are known for their easy and fast installation, seamless finish, wear resistance, weather resistance, resistant to alkaline cleaners, battery acids, and fuels and long term durability. The offered waterproofing products are developed using optimum quality components and creative technology. Before the final delivery, these waterproofing products are strictly tested on several parameters by the quality examiners assuring their effectiveness. We also provide optimum-grade packaging options for the entire range of polyurethane-based waterproofing. Rely on us for the polyurethane-based waterproofing products that are offered at market leading prices.

Polyurethane Waterproofing

SINGLE COMPONENT POLYURETHANE BASED WATERPROOFING SYSTEM

DESCRIPTIONPerma Elasto Shield PU is a single component VOC compliant, ready to use, liquid polyurethane based waterproofing membrane. It is composed of a blend of polyurethane and selected hydrophobic fillers, minerals, gelling agents and special stabilizers. It cures by reaction with humidity, maintains its elasticity and is suitable for use both on horizontal as well as vertical surfaces. Upon curing Perma Elasto Shield PU forms a tough and flexible membrane which is resistant to a wide range of temperatures, oxidation, radiation and Ultra Violet light.

PRIMARY USESPerma Elasto Shield PU is suitable for use in waterproofing roofs, terraces, podium, multi level car parking, terrace gardens, basements etc. It is highly useful in waterproofing wet areas such as sunk slabs of toilets and bathrooms, built up roofs, masonry and concrete walls, bridge decks, metal and plastic roofs and also repairing old roofs.

ADVANTAGES

• Perma Elasto Shield PU is non toxic hence complies with green building product requirement.
• Perma Elasto Shield PU is a highly elastic product and forms a rubber like membrane which is capable of withstanding severe expansion, contraction and deck movements.
• The membrane remains crack free under severe exposures to oxidation, ozone, UV light and temperature conditions.
• The product has superior wetting and adhesion properties which ensure superior bond with any kind of substrate and helps in getting over peeling problems.
• Perma Elasto Shield PU when applied adapts to any irregular surface forming a waterproof blanket.

DIRECTIONS FOR USESurface to be waterproofed shall be dry, clean, sound and free of all contaminants which may interfere with adhesion or proper curing .The substrates should not contain holes or cracks and should be dust free. All shrinkage cracks shall be treated with suitable material.

Application:Perma Elasto Shield PU is spread at the desired thickness onto the prepared surface. The coating is applied from the container using standard roofing brushes, squeegees or airless spray equipment at the recommended coverage rates on properly cleaned and prepared dry substrates. Application of the Perma Elasto Shield PU system should be done in one complete step to create a smooth uniform self leveling surface without cold joints, lines or streaks. Apply the first coat at the rate of 500 micron thickness. Let it dry fully (approximately 4-6 hours should be waited between two layers), then apply the second coat (500 micron thickness) .Waiting time shortens in hot weather and lengthens in cold weather.Caution:- Do not mix with water and do not apply on moist surfaces. The surface to be applied should be free of moisture.

HEALTH AND SAFETY

• Wear protective clothing, gloves and goggles.
• Skin: Avoid repeated or prolonged contact, if contact occurs , clean with hand cleaner that removes oil or grease , then clean with soap and water.
• Eyes: Contact could cause irritation. If contact occurs , flush with clean water.
• Inhalation: Can cause dizziness. Remove to fresh air and if breathing difficulty persist administer oxygen.

PACKINGPerma Elasto Shield PU is available in 20 kg. packs only.

SHELF LIFEPerma Elasto Shield PU has a shelf life of 12 months if stored in a cool and dry place in original packing from the date of manufacture.

DISCLAIMER

• PERMA warrants that all products are free from any defects of manufacture and comply with the specifications given in their respective technical data sheet. No warranty can be given as to the results of use because conditions of use, such as site conditions, surface preparations, workmanship, weather, structural issues and other factors are beyond the control of PERMA. Purchaser agrees to seek the advice of qualified professionals to carry out tests & take trials to determine the suitability of products for their intended purpose prior to full scale usage of PERMA products and assumes all risks.
• The company does not assume any liability for unsatisfactory results, arising from the use of our products. Purchaser’s sole liability is limited to replacement of product or refund of the purchase price paid if any product proven defective. No other warranties, express or implied, shall apply including any warranty of merchantability or fitness for a particular purpose.
• PERMA shall not be liable for any consequential damages arising from the use of our products for unsatisfactory results.
• The information supplied in this datasheet is based on our experience through extensive research and is given in good faith in order to help prospective users. We reserve the right to update the information provided in our technical data sheet at any time without prior notice within the scope of technical progress or new developments.

Perma Master Patch - NS is a high performance epoxy resin based structural repair system that provides a smooth finish to the repaired areas. Perma Master Patch - NS is a two component product based on epoxy base and Hardener which needs only on site addition of quartz ball Milli powder or silica flour to produce a non slump paste which is used for repairing beam and column edges and spelled/Honeycombed concrete. Advantages :

• Very strong repair material
• The repair mortar paste is non slump
• Repaired areas can be put to use faster

Packing : Perma Master Patch - NS is supplied in 250 grams and 1 kg pre weighed units.

we are offering perma epoxy. perma epoxy 100 - eg is a two component epoxy suitable for injecting into the porous concrete to consolidate the structural elements. primary uses :

• perma epoxy 100 - eg is developed as a low viscosity easy flowing epoxy resin system which travels easily in the body of concrete and consolidates all loose particles
• perma epoxy 100 - eg is used for consolidating the concrete mass in weak concrete structures
• perma epoxy 100 - eg is used for preventing water contact of reinforcement in structures which hold water on one side
• perma epoxy 100 - eg is used for water proofing leaky porous concrete structures

advantages :

• perma epoxy 100 - eg is a low viscosity product hence flows freely even into the finest cracks and pores of concrete
• perma epoxy 100 - eg is fast setting hence bleeding wastage of the product are minimized
• perma epoxy 100 - eg is supplied in pre weighed containers in the proportion of mixing hence convenient to use

packing : perma epoxy 100 - eg base & reactors are supplied in 1kg, 40kg packing download

Perma Master Fill - EP is a two component filled epoxy system which needs mixing of the two components thoroughly to produce a knifing putty. Perma Master Fill - EP is suitable for filling fine cracks depressions on the surface and repairing honey combs in the concrete to make it fair faced and suitable for subsequent coating. Perma Master Fill - EP is solvent free and chemical resistant. Primary Uses :

• For repairing surface blemishes
• For filling cracks
• For smoothing concrete as well as metal surfaces before painting

Advantages :

• Non toxic can be mixed by hand
• Durable
• Solvent free
• Easy to use. Requires two components to be mixed in equal proportions
• Chemical resistant
• Easily applied by putty blades or metal floats
• Non slump can be easily applied on vertical surfaces
• Reduces usage of subsequent coatings
• Cure without shrinkage
• Color matched to parent concrete

Packing : 1 kg.

Perma Anchor Fix - 80 is a polyester resin based grout which is used in locations where very high early and ultimate strengths are required along with chemical resistance properties. The product is supplied in pre measured two component units. Primary Uses :Perma Anchor Fix - 80 is used for installation of dowel bars in concrete and for providing starter bars in RCC structures for continuation structural concrete or in extension of structural members. Perma Anchor Fix - 80 can be used for fixing foundation bolts, base plates and rail tracks. Because of its thixotropic nature the product is successfully used in vertical horizontal as well as in over-head applications. Packing : Perma Anchor Fix - 80 is available in 250gm and 1Kg packing apart from bulk on special request. Download

Perma Coarse Putty is a fine powder in white color based on white cement. Selected polymers and Fillers. Primary Uses :For creation of level surface for application of line putty to the walls and ceiling. lt can be used on plasters, HCC or brick or block work directly. Direction for use :

• Clean the surface to remove dirt. Dust. laitance, oil, grease etc. Dampen concrete or the plastered surface before application
• lf the plastered surface has pores treat surface with SBR diluted 1:1 with water so that all the pores are primed then apply putty made to a flowing consistency so that all the pores get filled up then apply level putty
• Mix 250 to 3DD ml of clean water to 1 kg Perma Coarse Putty mix thoroughly and keep it for 5 to 10 minutes and remix to obtain an eyen consistency creamy paste
• Apply this paste on tile plaster on concrete surface with Spatula or putty blade lf there is a need to build up thickness it can he applied in layers taking care to see that the first layers has dried before the second layer is applied

Packing : Perma Coarse Putty is supplied in 20 kg & 40 Kg.

Perma Floor Top is a floor hardening compound based on non-oxidising metallic or non metallic aggregates a blend of ordinary Portland cements and activating chemicals. Perma Floor Top is for use on green concrete of industrial floors to achieve high abrasion and impact resistance properties on the finished floors. Depending upon the selection of aggregates Perma Floor Top is available in two grades.

• Perma Floor Top AI : Based on non-oxidising metallic aggregates
• Perma Floor Top az : Based on non-metallic aggregates

Primary Uses : Perma Floor Top products are designed for high abrasion and impact resistance properties to the concrete floors. Packing : Available In 50 kgs sack

Perma Grout 80 is a free flowing, non shrink super high strength grout mix. This Perma Grout 80 is supplied in a grey powder that requires only on site addition of water to form a ready to use grout slurry. We are the Manufacturer, Exporter and Supplier of the optimum quality Perma Grout 80 in the global market. Our range of Perma Grout 80 is available at market leading prices. Primary Use : Perma Grout � 80 is used for:

• Grouting heavy machine foundation which is subjected to huge dynamic loads.
• Grouting underneath base plates of machines.
• Grouting of column / stanchion foudations.
• Grouting of crane rails anchor bolts dowel bars, etc.

Packing : Perma Grout � 80 is avialable in 50 kgs Hdpe lined sack.

Perma Grout 60 is a free flowing, non-shrink grout mix. Our Perma Grout 60 is known for its high strength. Perma Grout 60 is supplied in a grey powder form, which needs only onsite addition of water to form a ready to use grout slurry. Thus, we are a famous Manufacturer, Supplier and Exporter of Perma Grout 60 in India.

 

Primary Uses : Perma Grout 60 is used for :

• Grouting heavy machine foundations, which are subjected to huge dynamic loads.
• Grouting underneath base plates of machines.
• Grouting of column/stanchion foundations.
• Grouting of crane rails anchor bolts dowel bars etc.

Perma Rapid Repair is a free flowing fine powder designed to achieve a quick repair system for concrete structures. The product achieves very high strength with in minutes. Primary Uses : Perma Rapid Repair is suitable in the following areas : To repair edges of columns and beams damaged during de-shuttering To repair ceiling concrete damaged while de-shuttering To repair edges at doors and windows To repair general honey combs Advantages : Perma Rapid Repair becomes hard and achieves high strengths within minutes or repair It is non shrink It is easy to use It is economical to use Replaces costly phenolic resin system Packing : Perma Rapid Repair is available in 1 kgs, 10 kgs and 25 kgs packing.

Perma Grout is a fine cementitiouls powder which forms a neat slurry when mixed with water.This slurry is used for injection grouting. Injection grouting to arrest leakage has been an age old practice. If concrete is porous or honey combed the cement slurry which is used for injection grouting partly blocks the voids and capillary. Perma Grout is a specialized cementitious powder which is designed for effective injection grouting of R.C.C Structure to arrest leakages. Primary Uses :Perma Grout is used for injection grouting to arrest leakages in most R.C.C. structure such as :

• Roof slabs
• Under ground and over head water tanks
• Basements
• Retaining walls
• Water retaining structures
• Earthen bunds etc.

Perma Grout is also used for densifying loosened weak concrete. Advantages :

• Perma Grout effectively fills capillaries and voids and does not shrink like cement slurries
• Perma Grout flows through the concrete easily and expands in voids and capillaries
• Perma Grout is very economical when compared with epoxy and polyurethane grouts

Packing : Perma Grout is supplied in 10kg and 25 kg sacks.

Perma Plaster Putty is a fine powder in white and light grey colour based on ordinary portland cement / white cement, selected polymers and fillers. This product provides a final surface for application of paint on to the walls and ceiling.This product can also be used for exterior application. Primary Uses :Creation of smooth surface for application of paint to the wall sand ceiling. It can be used on plasters, RCC or brick or block work directly. Packing : Perma Plaster Putty white/grey is available in 1Kg, 5kg, 20kg & 40kg multi wall laminated sacks

Perma Crackfill or Concrete Repair Mortar is a specially formulated repair mortar designed to fully meet the requirement of effectively repairing cracks in plasters and in concrete, avoiding the use of costly sealants and putties. Concrete Repair Mortar or Perma Crackfill is a dry powder when mixed with water it forms a creamy consistency paste which is ready for use in repairing cracks and repairing plasters. Concrete Repair Mortar or Perma Crackfill is reinforced with alkali resistant fibers. perma crackfill is available in grey and off white colour powder. Primary Uses :

• Perma Crackfill is ideally suited for repairing of superficial plaster cracks as well as structural cracks
• Perma Crack fill can be used for repairing ceiling cracks and plasters with ease because of its viscosity
• Cracks arising due to plasters cracking at junctions of wall and column or brick work and suffix of beam can be effectively sealed
• Cracks at parapet wall junction and roof slabs are also sealed with Perma Crackfill
• The product is suitable for rendering
• As a non-shrink waterproof filler in between RCC and brick/block work

Advantages :Perma Crack fill replaces costly sealant and putties. It is non shrink, hence possibility of shrinkage cracks are non existent. It has high tensile strength and good adhesion property. The finish achieved is sufficiently smooth. Good resistance to freeze / thaw cycles, carbonation and attack by chlorides. Conventional curing is not required. Packing : Available in 1 kg, 10 kgs and 25 kgs packs

Perma Flowcrete is a cementitious grey powder with micro fine aggregates. Our Perma Flowcrete allows re-concreting of the damaged, dilapidated structures. Perma Flowcrete needs only addition of water to form a free flowing concrete with enormous initial and final strengths. Our Perma Flowcrete gives strength to the columns and beams with high speed. Primary Uses : Perma Flowcrete is useful to reconstruct parts of beams and columns with far superior strength and with very high speed. Grouting structural cut outs and recess in sanitary fittings like floor traps, annular spaces of pipe passes through walls etc., in residential buildings. Packing : Perma Flowcrete is supplied in 25 kgs sack

Perma Plaster Putty Gold is very fine quality powder putty with high polymer content and very refined fillers. This Perma Plaster Putty Gold provides an ideal base for expensive and good quality paints. We manufacture, export and supply the finest range of Perma Plaster Putty Gold to our esteemed clients worldwide. We make avail this Perma Plaster Putty Gold to our customer at the most affordable price. Primary Uses : Creation of smooth surface for application of paint to the walls and ceiling. It can be used on plasters, RCC or brick or block work directly. Packing : Perma Plaster Putty gold is avialble in 20 kg & 40 kg multi wall laminated sacks.

322 - Perma Plast - O - Care is basically a skim-coat plaster that is offered in the powder form. It is characterized by the white color and is based on white cement, plus some fillers and polymers. It is absolutely resistant to water. We have carved a niche in the market as the prolific Manufacturers, Exporters, and Suppliers of Perma Plast - O - Care from Mumbai, India. Primary Use : For Creation of smooth even surface for application of paint to the walls and ceiling. It can be used on plasters, RCC or brick or block work directly. Packing : Perma Plast - O - Care is available in 20kg & 40kg HDPE Packing.

As we have been successful in emanating as a reliable brand among the customers, we are submerged in offering a high-quality range of free-flowing non-shrink grout for our esteemed clients. The offered product is used for precision grouting where it is essential to withstand static and dynamic loads. The offered grout is ideal for grouting of base plates of turbines, compressors, and boiler feed pumps. The free-flowing non-shrink grout can also be used for anchoring a wide range of fixings. We offer this grout at market leading prices to our clients. Additionally, in order to deliver consistent quality products to our clients, we keep our vigil eyes on product development, storage, and final dispatch.

Perma Floor Seal
 
CONCRETE FLOOR DUST PROOFER AND HARDENER

DESCRIPTIONEven the best concreted industrial floors loose their looks because of surface weakness and dusting. A small care such as use of a dust proofer and floor hardener on new floor at a very nominal cost ensures long life and good looks to an industrial floor. Perma Floor Seal is a micro Concrete  Dust Proofer which is diluted with water and applied on the floors to get the desired dust proof and healthy performance of floors.

PRIMARY USES

• To make the floor surface hard, durable and dust proof.
• Suitable for:
• Factory Floors
• Garages
• Industrial units
• Warehouses and transit sheds
• Generator rooms

ADVANTAGESBoth new as well as old floors can be treated with Perma Floor Seal. Perma Floor Seal makes the surface strong and durable. Perma Floor Seal makes the surface dust proof. There is no need for surface preparation and curing. The floor can be open to traffic even during treatment. It improves chemical resistance of the floor.

DIRECTIONS FOR USE

• Perma Floor Seal is applied on cleaned concrete floors in three coats with 12 hours intervals between coats.
• Dissolve 1 kg of Perma Floor Seal crystals in 6 litres of water and apply by brush, mop or just flood the surface.
• After 12 hours dissolve 1 kg of Perma Floor Seal Crystals in 3 Litres of water and apply as stated above.
• After 12 hours repeat operation (2) above.
• After 12 hours clean the surface with clean water and put it to use.

ACTIONPerma Floor Seal crystals when dissolved in water and applied on concrete surface, penetrates deep into the concrete through the capillaries and reacts with calcium oxide in cement to form non soluble crystals. These crystals effectively block the capillaries and effectively fill up all the surface pores making the whole concrete dense. This minimises penetration of chemical spillages etc. into concrete thus making it weak. The pore blocked surface becomes dust free.

COVERAGE1st Coat 250 gms/100 sq.ft. subsequent coats 400 gms/ 100 sq.ft. For three coats 1 kg covers 100 sq.ft.

HEALTH AND SAFETYPerma Floor Seal produces a strong alkaline solution. Eyes and skin should be protected from splashing. Contact with skin should be washed with plenty of water. If eyes are affected clean with adequate running water and seek medical help. During treatment hand gloves and gum boots are recommended.

PACKINGPerma Floor Seal is available in 25 kg HDPE sack.

SHELF LIFEPerma Floor Seal has a shelf life of 24 months if kept in cool and dry conditions.

Perma Plaster Putty Colour

HIGHLY POLYMERIZED CEMENTITIOUS COLOUR PUTTY FOR INTERIOR APPLICATION

DESCRIPTIONPerma Plaster Putty Colour is a very fine quality powder putty with high polymer content and very refined fillers. This provides an ideal base for expensive and good quality paints.

PRIMARY USESCreation of smooth surface for application of paint to the walls and ceilings. It can be used on plasters, RCC or brick or block work directly.

DIRECTIONS FOR USE

• Clean the surface to remove dirt, dust, laitance, oil, grease etc. Dampen concrete or the plastered surface if it is very dry or wherever required.
• If the plastered surface has pores treat the surface with SBR diluted 1: 1 with water so that all the pores are primed. Subsequently then apply putty made to a flowing     consistency so that all the pores get filled up then apply putty.
• Mix 350 to 390 ml of clean water to 1 kg Perma Plaster Putty with the help of a mechanical mixer. Mix thoroughly and keep it for 5 to 10 minutes and then re-mix to obtain an even consistency creamy paste. Apply this paste on the plaster or brick or block work or concrete surface with spatula or putty blade. If there is a need to build up thickness it can be applied in layers taking care to see that the first layer has dried before the second layer is applied. One day light curing may be considered for optimum result. Sand paper the surface next day to perfect evenness with sand paper no. 500 and dust clean before application of paint.

PACKINGPerma Plaster Putty Colour is available in 20 kg & 40 kg multi wall laminated sacks.

Permacem

ADDITIVE FOR UNDERLAYMENT TO UNEVEN FLOOR

DESCRIPTIONPermacem is a special hydraulic binder, which in combination with graded aggregates and water is used for preparing shrinkage compensated, fast setting high strength screeds, to create a base for laying of floor tiles, whether ceramic, wooden, linoleum, PVC etc ; carpeting or laying any other flooring system.

ADVANTAGES

• Permacem needs only addition of graded aggregates and recommended amount of water for preparing strong quick drying dependable mortar which is easy to mix and use.
• Permacem is shrinkage compensated and hence there are no chances of shrinkage cracks. It is quick drying. Tiling mortars or self-leveling screeds can be laid within 3 to 4 hours of laying of Permacem screed.

DIRECTIONS FOR USE

• SURFACE PREPARATION : Surface to receive Permacem screed should be sound, clean and free from any deleterious matter. It should be primed with water or SBR-OPC bonding slurry depending on whether it is an un-bonded or bonded screed
• MIXING AND LAYING : Mix Permacem with graded sand of size 0-8 mm in the proportion of 1 : 6 by weight and add water at a dosage of about 35% by weight of Permacem in a mixer and immediately lay the screed mortar on the prepared surface and spread, level and compact it. For laying bonded screeds, first apply boning slurry prepared by mixing PERMA BOND SBR and OPC in the proportion of 1:1 by volume on the surface immediately before laying Permacem screed.

PRECAUTIONS

• Do not use Permacem on surfaces subjected to rising dampness, In such cases waterproof the substrate first.
• Do not use secondary binders such as other cements, lime, gypsum etc., with Permacem .
• Take care to see that the aggregates are suitably graded, do not use only fine or coarse aggregates with Permacem .
• Have a good control over water. Excess or insufficient water from the recommendation will result in loss of strength and performance of Permacem .
• Do not leave Permacem mix in the mixer for more than 3-4 minutes.

PACKINGPermacem is available in 25 kg and 50 kg SACKS.

Perma Bond Aid

POLYMER BASED CEMENTITIOUS COMPOUND FOR CREATING MECHANICAL KEY FOR RENDERING AND SUBSEQUENT FINISHES ON DIFFICULT SURFACES

DESCRIPTIONPerma Bond Aid is a polymer based free flowing cementitious powder, which when mixed with water forms a mortar. This mortar is applied on difficult and non porous surfaces such as granite slabs, smooth RCC surfaces, concrete walls etc and combed with a notch trowel to create a mechanical key for further renderings and for using adhesives etc.

PRIMARY USESPerma Bond Aid finds its utility in rendering, stone fixing jobs and also when plastering on unhacked surfaces. Dense and non absorptive stones are often difficult to fix with regular cement mortar, so is the case with fixing of door and window frames of granites and other natural stones. A mechanical key if created helps in fixing these stones easily. Vitrified tiles of large dimension because of their non absorptive nature are also difficult to fix. In this case the mechanical key created by Perma Bond Aid becomes an economical and effective means for fixing these tiles.

ADVANTAGESSingle component product, needs just addition of water, on site just before use. Hence it is easy to use. Product is economical as against epoxies which are used for creating mechanical key. The product is eco friendly.

DIRECTIONS FOR USE

• Clean the surface to be treated to remove any oily or greasy contaminations by thoroughly washing it and allow it to dry. Ensure that the back of the tile or the stone which is going to be treated is also clean and sound. Add water to Perma Bond Aid in the proportion of 150 ml to 180ml (Depending on the sur face condition) water to one kg powder and mix thoroughly. Apply this paste on the back of the tile or stone surface with a trowel evenly. Using a notch trowel of 10mm, comb the surface to get uniform grooves and allow the paste to dry for 72 hours. If the surface which is supposed to receive the tile or cladding is also difficult or smooth, then do the same procedure on the surface as well and allow it to dry for 72 hours. Apply tile adhesive or fixing mortar on to the back of the tile or stone as well as on to the surface to be tiled or cladded and press the tile in position.
• Oat on to the smoot Mix Perma Bond Aid with water 3.5 times of Powder to 1 volume of water and mix the same to a smooth paste consistency. Apply the mix using a notch trowel h concrete surface and allow it to dry. On the hardened Perma Bond Aid surface apply normal plaster as per regular application procedure.

YIELD / COVERAGEPerma Bond Aid gives a yield of 12 Ltrs. when mixed with 25 Kg powder. 60 kgs of Perma Bond Aid covers an area of 70 sq.ft when applied with a notch trowel to a thickness of 4 mm.

PACKINGPerma Bond Aid is available in 10kg & 25kg sacks.

SHELF LIFEPerma Bond Aid has a shelf life of 12 months if stored in sealed original packing in a cool and dry place away from moisture and heat. If the storage is in moist and humid conditions shelf life may drop to 3 to 4 months.

Readymade shrinkage free mortar for repair of heritage structures.

 

DESCRIPTION : Though the product is very slow in setting and strength development, which is primary quality of hydraulic lime, it achieves good strength and durability parameters with age.Perma Heritage Mortar-5 is an off white colored powder which when mixed with water forms a pasty consistency mortar. This mortar is used for building up sur faces and repair of architectural features in a building exterior. The product is based on hydraulic lime, compatible polymers and

 

PRIMARY USES : Perma Heritage Mortar – 5 is used for creating architectural features in the building exteriors. It is used for repairing historic structures which are composed of non cementitious mortars and concretes. This mortar has low shrinkage characteristics and hence does not develop shrinkage stresses over the repaired substrate and hence is safe and durable.

 

DIRECTION FOR USE : nish is done with Heritage Mortar – final filling up the surface. This mortar is available as Perma Heritage Mortar – 10. This mortar can be put in layers of 10 mm to build up the thickness and first layer to dry before application of the subsequent layer. In large areas it is preferable to used a coarse grained Mortar for finish. This product is applied in thin layers of 5 to 6 mm. If there is a need to build up the thickness, then it is applied in layers after allowing the Clean the surface to remove dirt, dust, laitance, oil, grease etc. Dampen the surface wherever it is dry. Mix the Heritage mortar with water in the recommended proportion of water to form a smooth consistency paste. Apply this paste on the surface to be repaired and tool it to the desired

 

PACKAGING : Perma Heritage Mortar-5 is available in 25 kg & 50 kg packing.

Perma Anchor Fix - 80 is a polyester resin based grout which is used in locations where very high early and ultimate strengths are required along with chemical resistance properties. The product is supplied in pre measured two component units. Primary Uses :Perma Anchor Fix - 80 is used for installation of dowel bars in concrete and for providing starter bars in RCC structures for continuation structural concrete or in extension of structural members. Perma Anchor Fix - 80 can be used for fixing foundation bolts, base plates and rail tracks. Because of its thixotropic nature the product is successfully used in vertical horizontal as well as in over-head applications. Packing : Perma Anchor Fix - 80 is available in 250gm and 1Kg packing apart from bulk on special request.

Perma crackfill Paste is a highly flexible crack filter ideally suited for effectively sealing nogging moving plaster cracks whether internal or external. Primary Uses :

• Perma Crackfill-Paste ideally suited for repairing cracks in plaster whether internal or external
• Perma Crackfill-Paste is useful in sealing cracks in the sealing and at the junctions of brickwork and columns or beams
• Perma Crackfill-Paste is highly use full in water Proofing Applications Around door and window frames and around bath Tub, wash basin etc.

Packing : Perma Crackfill -Paste is Available in 200 Gms 400 Gms, 1 Kg & 15 kg Pakes

We cater for the global market with highly efficient 118 A - Perma Aluminium Polynet Butyl. We are hailing as the chief Manufacturer, Exporter, and Supplier of Perma Aluminium Polynet Butyl from Mumbai, India. This chemical is endowed with excellent waterproofing property, which makes it stand out among the lot. It is deemed ideal for the construction industry. To avail it minimal prices, contact us!

Primary Use

• Perma Aluminium Polynet Butyl Tape is used for covering all cracks, Construction joints, bends, Corners and joints of non homogenous materials. Perma Alumunium Polynet Butyl Tape is used for joint sealing of the metallic and non metallic roofing such as aluminium, zinc asbestos sheeting and the roofs of buses.
• Perma Alumunium Polynet Butyl tape can be used for sealing all joints in timber framed houses.
• It is used for sealing all the corner joints and the joints between the horizontal and vertical RCC surfaces of the sunken slabs of toilets and bathrooms after water proofing. It is also used for covering of all cut outs and pipe joints in the walls.
• This tape is used for covering The insulated air conditioning ducts and exposed Piping work to prevent energy loss.
• Perma Alumunium Polynet Butyl tape can be used to cover the ends of corrugated sheets in roofing & Sealing the joints around turbovents.

Advantages

• Perma Alumunium Polynet Butyl tape is resistant to hot and cold temperature. It withstands 90^o C Without yielding.
• Perma Alumunium Polynet Butyl tape is totally weather-proof. It insulates and makes the taped area waterproof and airtight.
• It has good adhesion to all types of surfaces.

Packing : Perma Alumunium Polynet Butyl tape are supplied in cartons. ASF-50, 16 rolls and ASF-100, 8 rolls per carton.

Perma Block Fix is a polymer modified adhesive mortar specially designed for thin bed fixing of masonry blocks of various kind including light weight blocks. This product helps in block fixing with thin water tight joints which are strong and give better bonding of the blocks in the masonry. Advantages :

• Perma Block Fix is a ready to use material which requires just addition water on site to make a ready to use mortar.
• Because of thin bed block fixing one can get extra strong bonding of the blocks and helps in achieving good plumb.
• Perma Block Fix joints are waterproof hence there is no chance of rising dampness in the masonry.
• No Soaking of the block required. No curing required.

Packing : Perma Block Fix is available in 25 Kg. and 50 kg. Sacks.

Perma Plast - NP is a superior quality super plasticizer cum water reducer based on high molecular weight sulphonated naphthalene formaldelyde condensate. Primary Uses :

• To increase the workability in concrete used in casting pre-cast units, cement tiles
• To brig about cement economies and in areas of congested reinforcement where high workability is desired
• For early de-moulding in pre-stressed concrete
• Perma Plast - NP is recommended where high initial and ultimate compressive strength is required
• Wastage due to breaking in pre-cast elements is minimized

Advantage :

• Perma Plast - NP is highly useful in pre-cast units and in tile factories and where high early strength is demanded
• Perma Plast - NP is very easy to dose. The dosing quantity of the material can beaded to the concrete or mortar mix at any stage of mixing
• Perma Plast â�� NP is very economical

Packing : Perma Plast - NP is supplied in 25 kg, 100 kg and 240 Kg HDPE drums

Perma Plast PC – 503

 

FOURTH GENERATION HYPERPLASTICIZER BASED ON POLYCARBOXYLIC CO-POLYMERS

 

DESCRIPTION

Perma Plast PC – 503 is a superior quality Super Plasticiser cum very high range water reducer based on high molecular weight Poly Carboxylic Copolymers.

 

PRIMARY USES

• To produce free flowing and self compacting concrete at a low dosage.
• To increase the compressive strengths of the concretes and mortars to highest possible limits.
• To bring down the water cement ratios to bare minimum.
• To achieve early high strengths.
• To achieve prolonged workability.

 

ADVANTAGES

• Perma Plast PC – 503 is a light colored liquid hence does not change the colour of concrete.
• Perma Plast PC – 503 is highly useful in precast units.
• Perma Plast PC – 503 is of special advantage in concreting RCC members with congested reinforcements.
• Perma Plast PC – 503 is very easy to dose. The dosing quantity of the material can be added to the concrete or mortar mix at any stage of mixing.
• Perma Plast PC – 503 is economical in usage because it works at low dosages for producing the same results when compared with commercially available PC based admixtures.

 

DIRECTIONS FOR USE

Perma Plast PC – 503 should be added to the concrete / mortar / cement paste mix during the mixing cycle at the same time as the water is added. Avoid adding Perma Plast PC – 501 directly to the dry cement.

 

ACTION

Perma Plast PC – 503 is a powerful plasticiser which disperses and deflocculates the cement particles within cement concrete / mortar or in paste. It is useful in increasing the workability of mix without addition of excess water or to allow reduction in free water content of the mix to achieve superior strength without in any way affecting the colour of the mix or the end product.

 

DOSAGE

Field trials should be conducted to determine the optimum dosage of Perma Plast PC – 503 for each application. However dosage range is between 100 gms to 1000 gms per 50 kg bag of cement depending upon the end results desired.

 

PACKING

Perma Plast PC – 503 is available in 25 kg, 100 kg and 200 kg HDPE drum.

 

SHELF LIFE

Perma Plast PC – 503 has a shelf life of 12 months if stored in manufacturer’s original packing in a cool and dry place away from moisture and heat.