Post Buy Requirement
Milestone Instruments
Delhi, India
gstGST : 07CQDPS2192A1Z0 Verified Add Review

Our Products

  1. Measuring Instruments & Equipment 4 Products available
  2. Laboratory Apparatus 19 Products available
  3. Soil Testing Equipment 3 Products available
  4. Testing Equipment 17 Products available
  5. Industrial Machinery 10 Products available
  6. Others 45 Products available

Measuring Instruments & Equipment #941314

Sand Pouring Cylinder

  • Sand Pouring Cylinder Apparatus 100mm Dia.
This Apparatus is used for determination of the dry density of compact, fine, medium grained soils and for layers not exceeding 50 cm thickness. A circular hole is dug into the ground, all the soil from within it collected, weighed and dried, and the hole back-filled with a standard uniform sand or fine gravel, poured from a calibrated container for calculating the volume of hole.
View Complete Details

Proctor Penetrometer

  • Proctor Penetrometer, Spring Type, 0-40 kg x 1The instrument consists of a needle attached to a spring loaded plunger, the stem of which is calibrated to read 0 to 40 kg division. Long stem is graduated at every 12.5mm to read depth of penetration and for use with needles of larger areas . The small penetration stem is also graduation in 12.5mm division and is used with needles of smaller areas. Needle points one each of 0.25, 0.5, 1.0, 1.5, 2.0, 3.5 and 6.0 sq Cm. and one tommy pin is supplied. Complete as above in a wooden carrying case.
  • Proctor Penetrometer, Hydraulic Type, 0-40 kg x 2This instruments is same as above but the penetration pressure on the needle is conveyed through a hydraulic system Comprises hydraulic proctor needle system complete with a pressure gauge fixed at easily readable angle reading 0-70 kg x 2 kg. A set of needle points consisting one each 0.25, 0.5, 1.0, 1.5, 2.0, 3.5 and 6.0 sq. cm. and a wooden carrying case.
  • Penetrometer, Proving Ring Type. (Vicksberg Penetrometer)Simple and light instrument for measuring static penetration resistance. The thrust force is provided directly by the operator who, by pushing on the T handle, forces the cone into the soil.The encountered resistance is measured on the fitted load ring. Testing is only possible in soils with good consistency and for short depths. Specifications1. 3 cones with 30 cone angle and 1 sq. inch sectional area2. 1 KN (100 kgf) load ring
View Complete Details

Infra-Red Moisture Meter

  • Capacity 5 g approx.
  • Sensitivity 10 mg approx

It is specially useful for determination of moisture in substance, that quickly reabsorbs moisture after drying. The infrared radiation is controlled by a voltage regulator and thereby provides excellent heat control. The instrument is provided with an indicator lamp. The torsion balance has a built-in magnetic damper to reduce pan vibrations enabling quicker weighing. The balance scale (drum) is divided in terms of moisture percentages on wet weight basis, which are read directly from it. Graduations are from 0 to 100% in 0.2 % divisions, but readings may be estimated to 0.1 % moisture content. It works on 230 V, 50 Hz, Single phase, AC Supply.

View Complete Details

Speedy Moisture Meter

Using a speedy moisture meter, the moisture content of soils, sand and other fine-grained material can be obtained quickly with reasonable accuracy. The test technique is based on the fact that water will react with calcium carbide to form acetylene gas and the quantity of gas formed is directly proportional to the water present, leaving a surplus of the chemical used in the test. The quantity of acetylene gas produced is indicated on a built-in pressure gauge, which is calibrated in percentage of moisture on wet weight basis.

  • Speedy Moisture Meter Range: 0 - 25%, Accuracy Division: 1%
  • Speedy Moisture Meter Range: 0 - 50%, Accuracy Division: 1%
View Complete Details
Tell Us What are you looking for? Will call you back

Contact Us