Under MaintenanceChecks both internal and external dimensions.multi gaugeApplications:Step diameters Inside & Outside.Center to center distance.Over pinball measurement for bigger size gears both for internal & external.Groove diameter measurement internal & external. Most useful in Pumps, Motors, Automobile Industries for Flywheels, Bearing Cap, Gears, Brake Drums, Rear Axle etc.Models: multi gauge-1MG 200: 30 to 200mm internal & external.MG 400: 100 to 400mm internal & external.MG 600: 300 to 600mm internal & external.Bigger Sizes also offered on request.

Advantages:

• Both Internal & External dimensions can be measured in one unit.
• Constant Measuring force eliminates feel of an operator.
• High sensitivity & Accuracy as movable arm holder moves virtually without play & friction.
• Actual dimensions of the parts can be determined.
• Non Contact Insertion by release lever so that measuring Jaws are protected.
• Any Dial Indicating Instrument with 8 mm mounting shank can be used.
• Large measuring Range
• Various applications are possible by changing the Jaws, which replaces number of instruments.

Advantages:

• Both Internal & External dimensions can be measured in one unit.
• Constant Measuring force eliminates feel of an operator.
• High sensitivity & Accuracy as movable arm holder moves virtually without play & friction.
• Actual dimensions of the parts can be determined.
• Non Contact Insertion by release lever so that measuring Jaws are protected.
• Any Dial Indicating Instrument with 8 mm mounting shank can be used.
• Large measuring Range
• Various applications are possible by changing the Jaws, which replaces number of instruments.

Advantages:

• Both Internal & External dimensions can be measured in one unit.
• Constant Measuring force eliminates feel of an operator.
• High sensitivity & Accuracy as movable arm holder moves virtually without play & friction.
• Actual dimensions of the parts can be determined.
• Non Contact Insertion by release lever so that measuring Jaws are protected.
• Any Dial Indicating Instrument with 8 mm mounting shank can be used.
• Large measuring Range
• Various applications are possible by changing the Jaws, which replaces number of instruments.

Available in 6 ranges in steps of 25mm, up to 150mm.

• Parallelism < 3 um for 0-25, 25-50 mm
• Parallelism < 4 um for 50-75, 75-100 mm
• Parallelism < 5 um for 100-125, 125-150 mm

Follows Abbe’s principle. Most useful for fast repetitive checks. Can be supplied with round 8 mm measuring anvil. Any indicating instrument with 8 mm shank diameter can Be used.
Measuring faces chamfered for ease of insertion. Measuring anvil Carbide tipped. Bigger sizes also offered on request.

Can be supplied for Through Bore/ Blind Bore applications. Adjustable depth collars can be provided for checking at specific depth. Please specify the unit for which Air Plug Gauge is required. Also MGPL can supply the air plug gauge in steel.

1.Carbide Plug Gauges are normally supplied with GO in Carbide & NOGO in Stabilised Steel.2.Both can be supplied in carbide as per requirement.3.MGPL gauges have excellent wall thickness to give desired results.Range0.5 to 8 mm Reversible type design8 to 40 mm Taper shank design40 to 60 mm Trilock Design60 400 mm Plate tyhpe Plug Gauge 4.Extra lenght up to 100 mm can be supplied as per requirement.

Features :

• Carbide Plug Gauges are normally supplied with GO in Carbide & NOGO in Stabilised Steel.
• Both can be supplied in carbide as per requirement.
• MGPL gauges have excellent wall thickness to give desired results.
• Extra lenght up to 100 mm can be supplied as per requirement.

Range

• 0.5 to 8 mm Reversible type design
• 8 to 40 mm Taper shank design
• 40 to 60 mm Trilock Design
• 60 400 mm Plate type Plug Gauge

Features :

• MGPL Carbide Ring Gauges are normally supplied GO in Carbide & NOGO in steel.
• GO & NOGO both can be supplied if required in Carbide.
• Setting Rings are manufactured in Carbide.
• Extra length Ring Gauges can be supplied.

Note : GO & NOGO Size Manufactured As Per IS 3455 (1971) Unless Specified.

MGPL has designed Carbide Width Gauges in reversible type design to suit :

• Piston Industries
• Pumps & Motors Industries
• Automobile & Crankshaft manufacturers.

Special gauges like Woodruff Width Gauges & Crankpin Width Gauges in Carbide are most suitable to crankshaft manufacturers. Setting Masters in +/-1 micron can be supplied.

Note: GO & NOGO Size Manufactured As Per IS 3455 (1971) Unless Specified

Features :

• Gauges as per customer design can be supplied.
• Supplied normally in single ended design.

Note: GO & NOGO Size Manufactured As Per IS 3455 (1971) Unless Specified.

Offered with Jet at Center or at Corne. Carbide Air Snap Gauge with Jet fixed in Carbide Tip.

Can be supplied for Through Bore/ Blind Bore applications. Adjustable depth collars can be provided for checking at specific depth.

Offered with Jet at Center or at Corner for stepped shaft. Also MGPL can supply the air ring gauge in steel. Please specify the unit for which Air Ring Gauge is required.

Under MaintenanceChecks both internal and external dimensions.multi gaugeApplications:Step diameters Inside & Outside.Center to center distance.Over pinball measurement for bigger size gears both for internal & external.Groove diameter measurement internal & external. Most useful in Pumps, Motors, Automobile Industries for Flywheels, Bearing Cap, Gears, Brake Drums, Rear Axle etc.Models: multi gauge-1MG 200: 30 to 200mm internal & external.MG 400: 100 to 400mm internal & external.MG 600: 300 to 600mm internal & external.Bigger Sizes also offered on request.

Advantages:

• Both Internal & External dimensions can be measured in one unit.
• Constant Measuring force eliminates feel of an operator.
• High sensitivity & Accuracy as movable arm holder moves virtually without play & friction.
• Actual dimensions of the parts can be determined.
• Non Contact Insertion by release lever so that measuring Jaws are protected.
• Any Dial Indicating Instrument with 8 mm mounting shank can be used.
• Large measuring Range
• Various applications are possible by changing the Jaws, which replaces number of instruments.

Advantages:

• Both Internal & External dimensions can be measured in one unit.
• Constant Measuring force eliminates feel of an operator.
• High sensitivity & Accuracy as movable arm holder moves virtually without play & friction.
• Actual dimensions of the parts can be determined.
• Non Contact Insertion by release lever so that measuring Jaws are protected.
• Any Dial Indicating Instrument with 8 mm mounting shank can be used.
• Large measuring Range
• Various applications are possible by changing the Jaws, which replaces number of instruments.

Advantages:

• Both Internal & External dimensions can be measured in one unit.
• Constant Measuring force eliminates feel of an operator.
• High sensitivity & Accuracy as movable arm holder moves virtually without play & friction.
• Actual dimensions of the parts can be determined.
• Non Contact Insertion by release lever so that measuring Jaws are protected.
• Any Dial Indicating Instrument with 8 mm mounting shank can be used.
• Large measuring Range
• Various applications are possible by changing the Jaws, which replaces number of instruments.

Available in 6 ranges in steps of 25mm, up to 150mm.

• Parallelism < 3 um for 0-25, 25-50 mm
• Parallelism < 4 um for 50-75, 75-100 mm
• Parallelism < 5 um for 100-125, 125-150 mm

Follows Abbe’s principle. Most useful for fast repetitive checks. Can be supplied with round 8 mm measuring anvil. Any indicating instrument with 8 mm shank diameter can Be used.
Measuring faces chamfered for ease of insertion. Measuring anvil Carbide tipped. Bigger sizes also offered on request.

Can be supplied for Through Bore/ Blind Bore applications. Adjustable depth collars can be provided for checking at specific depth. Please specify the unit for which Air Plug Gauge is required. Also MGPL can supply the air plug gauge in steel.

1.Carbide Plug Gauges are normally supplied with GO in Carbide & NOGO in Stabilised Steel.2.Both can be supplied in carbide as per requirement.3.MGPL gauges have excellent wall thickness to give desired results.Range0.5 to 8 mm Reversible type design8 to 40 mm Taper shank design40 to 60 mm Trilock Design60 400 mm Plate tyhpe Plug Gauge 4.Extra lenght up to 100 mm can be supplied as per requirement.

Features :

• Carbide Plug Gauges are normally supplied with GO in Carbide & NOGO in Stabilised Steel.
• Both can be supplied in carbide as per requirement.
• MGPL gauges have excellent wall thickness to give desired results.
• Extra lenght up to 100 mm can be supplied as per requirement.

Range

• 0.5 to 8 mm Reversible type design
• 8 to 40 mm Taper shank design
• 40 to 60 mm Trilock Design
• 60 400 mm Plate type Plug Gauge

Features :

• MGPL Carbide Ring Gauges are normally supplied GO in Carbide & NOGO in steel.
• GO & NOGO both can be supplied if required in Carbide.
• Setting Rings are manufactured in Carbide.
• Extra length Ring Gauges can be supplied.

Note : GO & NOGO Size Manufactured As Per IS 3455 (1971) Unless Specified.

MGPL has designed Carbide Width Gauges in reversible type design to suit :

• Piston Industries
• Pumps & Motors Industries
• Automobile & Crankshaft manufacturers.

Special gauges like Woodruff Width Gauges & Crankpin Width Gauges in Carbide are most suitable to crankshaft manufacturers. Setting Masters in +/-1 micron can be supplied.

Note: GO & NOGO Size Manufactured As Per IS 3455 (1971) Unless Specified

Features :

• Gauges as per customer design can be supplied.
• Supplied normally in single ended design.

Note: GO & NOGO Size Manufactured As Per IS 3455 (1971) Unless Specified.

Offered with Jet at Center or at Corne. Carbide Air Snap Gauge with Jet fixed in Carbide Tip.

Can be supplied for Through Bore/ Blind Bore applications. Adjustable depth collars can be provided for checking at specific depth.

Offered with Jet at Center or at Corner for stepped shaft. Also MGPL can supply the air ring gauge in steel. Please specify the unit for which Air Ring Gauge is required.