MICROEMBESYS TECHNOLOGIES PVT LTD

Makarba, Ahmedabad, Gujarat

Following configurations with two to seven programming modules are available for ordering:

• Extremely fast.
• Computer controlled or standalone operations.
• User-configurable options with 2 to 7 CPI2-GM1 programming modules.
• Flexible re-targeting programming modules each single module in one CPI2-Gx can run its own project concurrently programming different device type on same target.
• Each module stores up to 4 projects (images) quickly switched by ATE signals.
• Modules in the programmer can be started synchronously or asynchronously.
• Multiple CPI2-Gx units can be daisy chained to form a very large-scale gang programming cluster with up to 72x CPI2-GM1 modules controlled by single computer.
• All ATE control lines are opto-isolated.
• Compact design enables embedding into programming fixtures.
• Programs devices with Vcc from 1.2V to 5.5V.
• Supports JTAG, SWD, SPI, SCI, IC, UART, and other interfaces.
• Supports ISP for devices with Vcc voltages in the range of 1.2V to 5.5V;
• Program certain devices over a long distance up to 5m (15ft).
• USB 2.0 High Speed and LAN communication interfaces.
• Intuitive, user-friendly graphical user interface (GUI).
• Simplified graphical user interface for use by unskilled personnel.
• Application Control Interface (ACI) and SDK.
• Enables control from programs in C, C++, C#, Visual Basic.
• Enables control from National Instrument LabVIEW.
• On-the-fly utility allows controlling already launched programmer.
• Create custom programming scripts with included scripting language.
• Reliable data and project settings protection.
• Tamperproof software and firmware.
• Compact design enables embedding CPI2-Gx gang programmers into test fixtures.

• CPI2-DEMUXlicense enables built-in demultiplexers on all programming modules in the CPI2-Gx unit and allows sequential programming through doubled number of channels.
• CPI2-GDMRexternal relay demultiplexer additionally doubles a number of programming channels for sequential programming.
• Combination of activatedCPI2-DEMUXlicense with twoCPI2-GDMRexternal relay demultiplexers allows quadrupling number of channels up to 28 (4 sequentially working groups by 7 programming channels each).
• CPI2-GTRB external relay barrier allows to galvanically disconnect all programmer signals from the target panel while it is under testing by ICT to prevent programming and testing signals interference. The GND lines can remain connected or can also be cut off.

• Compact mother board allows installation of up to 7 programming modules.
• Equipped with an embedded fan for 24/7 work in production environment.
• Compact and easily mountable inside of ATE.

• High Speed USB 2.0 (480Mbps).
• 100 Mbit/s Ethernet both dynamic and static IP addresses are supported.

• Comprehensive, user-friendly graphical user interface (GUI).
• User-configurable simplified interface (SUI) for use by unskilled personnel.
• Command line.
• Integration with National Instruments LabVIEW Software.
• Application Control Interface (ACI) and Software Development Kit (SDK).
• On-the-fly control utility allows changing commands in already launched and running programmer without stopping it.
• Script language for making custom user-defined scripts.
• From ATE start/stop and status signals individual for each single channel.
• Can be launched manually or automatically by closing the fixture lid.

• Unlimited number of projects can be created, stored and quickly invoked for launching.
• Each programming module stores up to 4 standalone projects for fast project switching.
• These 4 standalone projects can be identical or different for each module.
• Interface configurations, colors, fonts, sounds, hot keys, and other settings can be stored and quickly retrieved.

• External power adapter 9-18V@3A not included in the CPI2-Gx kit.

• Provides Vcc (1.2 to 5.5V @ up to 350mA) and Vpp (1.2 to 15V @ up to 80mA) to target panels.
• Target panels can be powered from external power supplies.

• Supports loading and saving files in all popular formats.
• Unlimited number of data buffers can be open simultaneously.
• Arithmetic operations on data blocks in buffers.
• Programmable serialization of target devices.
• Multiple serialization algorithms, including script-controlled ones.
• Allows writing of user-defined signatures and data blocks into target devices.
• Several different algorithms available for checksum calculation.
• Special DLL for user-defined checksum calculation.
• Stores logs of programming sessions with time-stamping.
• Easy to use GUI editor for device-specific settings and algorithm parameters, such as fuses, lock bits, protected sectors, boot loader vectors, clock frequency, etc.
• Displays a target device connection diagram right from the GUI.
• Comprehensive self-test and diagnostic procedures.

• CPI2-Gx unit has two Eurocard type R DIN 150-pinCPI2-DEMUXlicense is activated.
• Both A and B channels are identical with respect to electrical and timing characteristics.
• Ten target-specific logical inputs/outputs per channel settable in the range of 1.2V to 5.5V, individually programmable as I/O, GND or Vcc.
• For stable programming the above ten signal lines are interspersed with GND wires.
• Two inputs/outputs individually programmable as TTL logic I/O, GND, or Vcc or Vpp.

• 48-pin DINoutput status signals: BUSY, GOOD and ERROR separate for each channel;
• two inputs for selecting a standalone project (job) separate for each channel;
• one common input that control switches programming channels between A (main) and B (additional, demultiplexed).

• Main CPI2-Gx unit: 155 x 128 x 50 mm (6 x 5 x 2).
• CPI2-GDMRandCPI2-GTRBrelay blocks: 156 x 63 x 45 mm (6 x 2.5 x 1.75).

• Microsoft Windows XP, 7, 8 and 10.

• Real-time non-intrusive emulation for selected 8051 microcontrollers;
• Tiny emulator header that plugs directly into a target socket 95x70x40 mm;
• Connects to a PC USB or serial port;
• Up to 2M bytes program memory & 512K data memory (64K + 64K by default);
• Memory banking up to 32 banks by 64K;Memory mapping between the ICE and target with 256 bytes resolution;
• Up to 1M true hardware breakpoints at Program memory and memory access breakpoints;
• Up to 1M true hardware breakpoints at Xdata memory access for Read & Write;
• Breakpoints on access to on-chip data memories: SFRs, direct data memory, on-chip Xdata, etc.;
• 4 complex breakpoints / triggers;
• Up to 64K frame deep by 128 bit wide trace buffer (16K x 128K by default);
• Trace cablewith 8 micro hooks for entering signals and two hooks for outputting triggers;
• Precisely programmable clock generator;
• 48-bit on-board timer;
• Shadow RAM provides target device RAM real-time access without disturbing emulation;
• On-the-fly access to the memory, breakpoints, tracer, and timer;
• Memory coverage feature enables finding dead code;
• Precisely controlled voltage regulator 2.0 to 5.5V range;

• Project-level support for the Phyton assembler and C compilers from Keil, IAR and Raisonance;
• Source-level debugging for all popular C compilers and assemblers;

Download Demo

There are threemain boardconfigurations:

• MR2-52-03U provides emulation for 64K code + 64K data memory, does not support external memory banking;
• MR2-52-05U provides emulation for 1M code + 448K data memory, supports external memory banking.
• MR2-52-06U provides emulation for 2M code + 448K data memory, supports external memory banking.

APODor a daughter module is built around an execution processor that emulates a behavior of the target MCU being under control of the loaded application program. PICE-52 can be equipped with a variety of changeable PR2-52-xxx pods.

AnAdapterprovides mechanical connection of the emulator pod to the target board. It plugs directly to a DIP-40, PLCC-44 or QFP-44 target socket.

Phyton has been producing and selling 8051 in-circuit emulators for more than 20 years and keep selling them nowadays. To check if our 8051 emulators support your target device and would like to get a quote, please email your inquiry to info@phyton.com. Your request should include the following information about the target device and your development environment:

• Silicon manufacturer (for example: Atmel, NXP, Microchip, etc.);
• Device part number (for example: AT89C52ED2, SST89E516RD2, etc.);
• Mechanical chip package (for example: DIP 40-pin, PLCC 44-pin, etc.);
• Whether your target board has an external memory and, if so, its memory structure;
• A compiler brand, if used for project management.

We will be sure to respond to your request promptly.

• 67.6mm by 45mm (8-layer PCB design)
• 500MHz Atmel SAMA5D26/27 ARM Cortex-A5 Processors
• 256MB DDR3 SDRAM, 256MB Nand Flash , 4MB Data Flash, 64KB EEPROM
• On-board Ethernet PHY
• SO-DIMM 200-pin Expansion Connector
• Linux 4.1