Metal Bonds(India)

Phase II, Chandigarh

• Strong hot start.

• Digital display with current preset function.

• Auto protection from over voltage, over heat, over current.

• Economical energy usage, very low no-load consumption.

• Portable, light weight & compact size.

• Suitable for cutting of stainless steel, mild steel, copper, aluminium, alloy steel etc.

• Constant voltage (CV) type.

• Digital display, with current preset function, auto protection from voltage, over heat, over current.

• Economical energy usage / very low no-load consumption, adjustable slow speed function to ensure arc ignition, stable arc, smooth arc striking, low spatter, low noise, portable, light weight, compact size.

• Suitable for welding with solid wire & flux cored wires i.e. mild steel, stainless steel, alloy steel, high tensile steel and aluminium.

• 2 in 1 working, TIG & MMA both.

• With pulsing option & adjustable slow speed option function.

• Digital display, with current preset function.

• Auto protection from over voltage, over heat, over current.

• Economical energy usage, very low on load consumption.

• Stable arc, smooth arc striking, low spatter, low noise, portable, light weight & compact size.

• Suits to work with all kind of electrode i.e. rutile / basic / cellulose coated.

• Standard Accessories

  • TIG torch, cable connector 2 nos., 3 mtrs earth cable with clamp, 5 set of consumables.

  Optional Accessories

  • Argon gas regulator with flow meter.

These are available in Single, Double & triple Stage in Direct / V - Belt Driven Versions. These are Specially Designed and Fabricated to ensure High Efficiency & Trouble Free Operation and are Highly Resistant to severe conditions such as High Temperature, Corrosion and Abrasion. These are available in different materials of construction such as Carbon Steel, Stainless Steel, Aluminum, Rubber Lined, Epoxy Painted and FRP Fabricated.

PromivacConstruction
An Exhauster or Blower consists of a rotating system of Shaft & Impellers operating in a specially designed casing with Inlet & Outlet connections. The shaft is made of High Grade Carbon Steel, machined & ground to accommodate the Impellers & Bearings. The Impellers are a composite section of casting / fabricated from high tensile aluminum, MS/CRC sheet, accurately balanced & are held securely on the shaft by heavy endwise locknuts.

PromivacAdvantage
Straightforward Single / Multistage Design, Dynamically Balanced Impellers minimize vibration, No fine internal clearances or wearing parts, No lubrication required, Air delivered is free from Moisture & Oil Vapour, Low Noise Level, Low Power Consumption, Air delivered is free from pulsation & is uniform No need for Relief Valve, Versatile - Can be used for Suction & Blowing

PromivacOptional Accessories
Vibration Isolators & Flexible Connections at Inlet & Outlet can be provided to minimise transmission of Vibration, Inlet / Outlet Silencers to reduce Noise Level & Multivane Damper for controlling air. A suitably designed Vacuum Storage Tank can also be supplied with the unit to act as a reservoir to store Vacuum for Instant Evacuation.

PromivacApplications
Garment Pressing, Steam & Condensate Extracting, Vacuum Cleaning, Dust / trim collection, Pneumatic Conveying, Ventilation, Air Blowing & Boosting, Handling Hot Flue Gases, Agitation of Liquids, Bottle Drying & many more.

Promivac plants & systems which are known for their compact design, reliability and efficient performance, have earned enviable reputation in a short time. These are manufactured with high quality material & precision workmanship, in a well equipped workshop under the direct supervision of experienced and qualified engineers.

Trouble free service for a long time and readily available after sales service have made them all the more popular and hence are being widely accepted in laboratories, industries and research units of repute. We offer High Vacuum Coating units, High Vacuum Pumping Systems, Vacuum Metalizing Plants, Vacuum Annealing Plants, Vacuum Impregnation Plants, Vacuum Lifting & Conveying Systems, Vacuum De-Airing & De-Watering Systems, Vacuum Instruments & Equipments, Vacuum Measuring Apparatus, Diffusion Pumps, Traps, Valves, Gauges and other related components etc.

There should not be any cause of worry, if the already employed Vacuum Pump is found not competent enough to meet the requirements of the specific complex application, in terms of Pumping Speed, Ultimate Vacuum or Overall Performance, because now 'PROMIVAC' Mechanical Vacuum Boosters are there at your beck & call, just ready to come to your rescue by immediately taking over this challenging task.

Vacuum Boosters also known as Mechanical Boosters are dry pumps that meet most of the ideal Vacuum Pumping requirements. These are Positive Displacement type & are designed to handle large quantity of gases under low working pressures and are manufactured keeping close tolerances and ensuring complete air tightness. These are available in V-Belt / Direct Driven versions wherein the capacity can be varied as per choice.

A Vacuum Booster can be backed by various types of Vacuum Pumps such as Rotary Oil Sealed, Water-ring Vacuum Pump, Rotary Piston, Reciprocating Piston Pump, Dry Screw Pumps, Water / Steam Ejectors etc.

PromivacApplications
Vacuum Casting, Coating, Degassing, Distillation, Transformer Oil Purification, Food & Edible Oil Processing, Drying, Freezing, Furnaces, Impregnation, Automotive Fluid Filling, Metallizing, Polymerisation, Crystallisation, Sintering, Electron Beam Welding, Heat Treatment, Plasma Welding, Sputtering, Creating Low Density Wind Tunnels, Space Simulation and also in Industries like Pharmaceutical, Chemical, Fertilizer, Electric Bulb & Tube Manufacturing, Semi-Conductors & Petrochemicals.

PROMIVAC PUMPS, which are known for their Compact Design, Reliability & Efficient performance, have earned an enviable reputation in a short time and have become an ideal choice of discerning users for all types of Specialized and General Vacuum Applications in whichever field they exert; Chemical, Pharmaceutical, Research, Education and General Industrial Job Sectors are a few amongst many more to speak of. Provision of Reliable, Quick & Efficient After Sales Service have made them all the more popular with the users.
In response to the over whelming demand received from the market, PROMIVAC has come forth with a High Speed, Submersible Sewage / Effluent Submersible Pump. Each and every pump of this new series very successfully and effectively takes care of its respective job and hence as usual is held in similar high esteem the 'PROMIVAC' logo has already earned.
PromivacApplications

Effluent, Muddy Water Transfer, ETP, STP, Waste Water Treatment Plant, Swimming Pool, Dewatering of Ponds, Basements of large buildings and is also of use in Power Plants, Hospitals, Hotels, Chemical, Sugar, Steel & Cement Industries

Features :

• Tool is recommended for site /repair work.

• Portable tool , as no air compressor required.

• Can be operated at any 5amps plug point.

• Has a safety trigger , no accidental firing takes place.

• Tool is fitted with ON/OFF switch.

A good quality rubber compound bonded ( molded ) over a cast iron core forms a Bonded Rubber Tyre Wheel. The load carrying capacity as well as life of BRT wheel is much more than that of SRT wheel. Castings can be returned back to us for re-bonding of rubber when it is worn out

These wheels are manufactured by compression molding shredded cotton fabric, soaked in good quality phenolic resin. The hardness of Fibre wheel is higher than the hardness of UHMW wheel. As a result, the chance of steel burr lying on the shop floor getting embedded in the wheel surface is remote. The acidic or alkaline chemicals have little effect on these wheels.

Features :

• This tool is a pneumatically operated tool

• Air consumption 2.4CFM (when operated at 80 psi)

• Recommended pressure 5 bar to 7 Bar

• Has a full metal body & magazine

• This tool is a combination tool & accommodates35/18 & 15mm staples

• Can be used for 3/ 5 / 7 ply corrugated cartons.

Features :

• Tool is recommended for site /repair work.

• Portable tool , as no air compressor required.

• Can be operated at any 5amps plug point.

• Has a safety trigger , no accidental firing takes place

• 15 times faster than manual nailing

• Each nail enters with same pressure giving better quality

• Zero wastage of nails

• Reduces manpower substantially.1 person on site cancomplete the job of 6 people

• Capacity of brads from 15mm to 30mm

• High resistance body in fiberglass reinforced resin

• No carbon or armature. Has a solenoid coil & electronic circuit

• Removable front plate for easy unjamming

• Rear loading with built-in pusher

• Much lighter than metal slings, easy to handle.

• High performance fibre, high safety.

• Non corrosive, non conductive, non sparking.

• Very simple, easy and safe to operate.

• Prevention of slip and damage on the surface of finished goods.

• Wide surface hence less pressure at the points of contact of the lifting object.

Features :

• Rubber comfort grip

• Rear exhaust

• Noiseless tool

Features :

• All steel body

• Convenient bottom loading

• Comfortable plastic handle

Heavy Duty castorsare recommended where floor conditions are not good & MD castors needs frequent replacement. These castors can withstand occasional shock loads & higher speeds. Heavy Duty swivel castors are of two types. i.e. HD-F & HD-C. However, important dimensions such as mounting holes, overall height etc. are exactly same for both types of castors. Therefore, matching fixed castor [ FX(HD) ] is same for both types of swivel castor. SRT, BRT, PU-PP, PU-CI, PP, NYL, UHMW, FBR, CI wheels can be used inheavy duty castors.

Twin castors have the advantages of greater load carrying capacity for the same castor height. The load is distributed over a wide floor area. But because of the differential movement of two wheels, the scrubbing action that arises on turning from the use of wide tread single wheel is avoided. The use of twin castor is, therefore, advantageous than use of single wheel castor with wider tread width of the wheel. Attachments such as wheel lock, wheel brake & swivel lock can be provided on these castors.
SRT, BRT, PU-PP, PU-CI, PP, NYL, UHMW, FBR, CI wheels can be used in heavy duty twin castors.

Light duty extra strength castors are particularly suitable where LD castors fails too frequently & where loads are moderate. Both LD & LD-X castors looks like same. Only difference is LD-X castors are manufactured from higher plate thickness.

SRT, PU-PP, PP, UHMW wheels are assembled in LD & LD-X castors

Medium Duty castors are designed to carry moderate loads i.e. more than LD or LD-X castors, and are suitable for various types of trolleys used in industries, warehouses, godowns, stores, railway platform and so on. These castors are also suitable for hospital furniture, laboratory equipments or food serving trolleys where load carrying capacity required is higher & the light duty castors need frequent replacement.

SRT, BRT, PU-PP, PU-CI, PP, NYL, UHMW, FBR, CI wheels can be used in medium duty castors.

Features :

• Perfect tool for installation of solid hard woodtongue & groove joint
• Non marring mallet (1.3kg) accompanies thetool for operation
• Tool has easy jam free operation and canaccommodate up to 120 cleat nails
• Portable tool which can be taken to sites as noelectricity required at all
• Large base to increase stability and minimizedamage to pre-finished floors.
• Quick loading magazine with spring loadedpusher
• Tool recommended for solid wood having 8mm -15mmthickness
• Tool shoots a cleat nail at 45 degree angle intowood
• Cleat nails minimize wood splitting and stillallows expansion and contraction of the woodmaterial

• Wire rope hoists are designed as per international standard and suitable for class IV duty operations squirrel cage crane duty induction motors, class F insulation.

• Compact design, easy maintenance.

• Rope drum is made of seamless pipe accurately machined & grooved to ensure proper seating of wire rope in a right layer.

• The rope guide is made of special closed grain casting & is designed and accurately machined to suit the grooves of the rope drum & prevent the rope from overriding & loosening. It also operates the limit switches provided as a safety features to limit the over hoisting & over lowering of the hook. The guide is so designed to ensure proper tensioning of the rope.

• Brake, motors, gear box & control panel are independent units and are accessible easily. The complete hoist can be easily maintained by keeping it in its installed position, thus saving on precious labour as well as down time maintenance time.

• Motorized trolleys are of adjustable type and fitted with ball bearing. Spacers are supplied to suit the wheel gap with recommended sizes of I-Beams.

• Heavy duty high tensile steel forged are used & fitted in such a manner that they rotate and swivel freely.

• 6 to 13 mm capacity
• Up to 14000 rpm spindle speed

• 25 to 35 mm capacity
• Auto Feed and Manual options available

• Manufactured in accordance with International standard for safety, quality and performance.

• Optimal Use of space - Very low head room.

• Increased efficiency - Two-stage reduction gear. Hardened Gears & Pinions-supported on roller bearings.

• Hardened load sheave with four precision-machined chain sprockets.

• Chain sprockets supported on roller bearings for smooth operated and low wear.

• Ratchet disc with double ratchet pawls, screw and disc brake are enclosed to protect the complete brake mechanism.

• Load chain is alloy steel grade 80 according to International Standard.

• Hook deformation indicators - Two strategically placed marks allow for measurement to determine if the throat opening has changed thus indicating abuse or overload.

• Equipped with top and bottom safety hooks which are designed to bend slowly to warn overloading and are made in accordance with International standard.

• Every chain block is operationally tested to 150% of the rated capacity.

• Safety factor : 4 times of the rated capacity.

• Every chain pulley block is warranted for 12 months from the date of sales against manufacturing defects (conditions apply).