M PLY is made from Best quality of laserable MDF. It is available in 1.6 mm, 2 mm and 2.5 mm in thickness. It can be cut very faster through laser machine compare to normal MDF material. It is available in 2 x 3 ft sheet size.

Wedding card industries
Tropy-Awards
Certificates
Plaques
Gift-articles
Chocolate-boxes
etc.

Overview Of GALAXY: W-200

Spot welding is an important and basic aspect of laser welding technology. When laser radiation heats the surface of work-piece, the surface head diffuses to the interior though thermal conduction and melts the work piece by controlling the width, energy, peak power and repeating frequency of laser pulse to form specific molten pool. Because of this unique feature, it is widely used in processing of precious jewelry or welding of precision parts.

The energy, pulse width, frequency and light spot size can be adjust in a large range to realize different welding effects. The parameters are adjusted by the lever in the seal cavity, which is simple and highly efficient.

Ceramic converging cavity is imported from the Britain, it is corrosion resistant and high temperature resistant with 8-10 years service life. The life of xenon lamp is more then 8 million times.

Most advanced light shielding system eliminates the irritation to eyes by laser during working.

able to work for 24 hours continuously; stable performances; free of maintenance in 10, 000 hours.

Human-based design accords with ergonomics, avoiding fatigue after long time working.

high speed, high efficiency, deep enough, slightly deformation, small heat effect area, high welding quality, pollution free, environmental friendly

Diamond Edge Polishing System

When using diamond edge polishing, edges on acrylic sheets are moved over sharp, fast-rotating diamonds. Properly done is the result so good that diamond polishing can be compared with cast surfaces. Moreover, the method is relatively inexpensive and can be performed on large batches.

Diamond edge polishing may be used on edges of shelves and signs that have previously been sawn to correct dimensions.

It should be noted that diamond edge polishing is exclusively for straight or sloping sides. Eg. it cannot be used on rounded corners

Special design of carriage where 2" lens or 5" lens both can be used. 5" lens gives you better quality of cutting, if the thickness of material is more than 10mm and 2" lens should be used for cutting media less than 10mm thickness.High quality touch panel display - very easy to usePass through design for long length of work piece in Y-axis directionMachine is provided with foot-mounting legs so that there is no vibration in machine and machine can be adjusted on zero levelAs it is made in India, No waiting period for spare parts & quick service supportMachine is provided with heavy duty compressor which has Air-assist combining adjustable focus systems in coaxial jet air to prevent cutting edge from burning downLaser cut software with window based software enhance cutting speed and angel / curve performanceLaser seals the edges of fabric while cuttingMaximum cutting thickness of acrylic - 20mmHigh quality of chiller unit for better performance and long life of laser tube

Chiller (Included)
1. Compact design, convenient for installation and operation.
2. All refrigeration components are international brand, which can offer good and stable cooling effect.
3. The water cycling system is consisted of stainless steel pump with instant flow and high lift, stainless steel water tank and PVC connectors.
4. Equipped with flow switch which can output protect signal.
5. High and low temperature alarm signal output, which can output normal close signal as options.
6. Digital display temperature controller, with multiple function settings and error alarming.

Overview Of GALAXY: WD

Galaxy WD 500 4 Axis laser welding machine with rotary jig and CNC control system is for welding Intersecting line, involute line, curve, point, the entire column and other arbitary trajectories. It is specialized R&D for precision welding industry with high magnification system and well received by customers.

Application Of GALAXY: WD

Suitable for welding of kettle, vacuum cup, stainless steel bowl, sensor, tungsten wire, high power diode (triode), aluminum alloy, laptop shell, mobile phone battery, door head, zinc alloy artwork.

Capable of welding spot, straight seam, circle, square or any plane graphs drawn by AUTOCAD, or even dimensional graphs.

The Fully automatic multifunction and double edge furring equipment.You can work with all foils (PVC, PET, PO etc.) high class foils as well as veneers or laminates.PVS film can be precisely pressed on uneven surfaces.Dual heater used for consistant heating.Stationary hot room reduces chances for damage to the heater assembly.Auto and manual both operations can be performed.Both side vacuum bed arrangement is possible for mass production.

Laser Fume Ventilator is designed for filtrating hazardous fumes and dusts which is generated in the process of laser processing, like laser cutting / engraving / marking/welding / cladding / coding etc. The main function of them is protecting the health of the employees, keeping the machines performance and decreasing environment pollution. Meantime, it can increase product quality, reduce potentional cost.

New for 2014/15, we are pleased to introduce Mehtas Laser Engravable aluminum sheet on which you can laser beautifully black images on gold, silver, white and silver images on black colour aluminum sheet. It can be widely use for making Signs, Advertising Decoration, Awards, Plaques, Trophies Labels, Nameplates, Electrical Products Panel/Cover, Personalized Metal Gifts etc.

M PLY is made from Best quality of laserable MDF. It is available in 1.6 mm, 2 mm and 2.5 mm in thickness. It can be cut very faster through laser machine compare to normal MDF material. It is available in 2 x 3 ft sheet size.

Wedding card industries
Tropy-Awards
Certificates
Plaques
Gift-articles
Chocolate-boxes
etc.

Overview Of GALAXY: W-200

Spot welding is an important and basic aspect of laser welding technology. When laser radiation heats the surface of work-piece, the surface head diffuses to the interior though thermal conduction and melts the work piece by controlling the width, energy, peak power and repeating frequency of laser pulse to form specific molten pool. Because of this unique feature, it is widely used in processing of precious jewelry or welding of precision parts.

The energy, pulse width, frequency and light spot size can be adjust in a large range to realize different welding effects. The parameters are adjusted by the lever in the seal cavity, which is simple and highly efficient.

Ceramic converging cavity is imported from the Britain, it is corrosion resistant and high temperature resistant with 8-10 years service life. The life of xenon lamp is more then 8 million times.

Most advanced light shielding system eliminates the irritation to eyes by laser during working.

able to work for 24 hours continuously; stable performances; free of maintenance in 10, 000 hours.

Human-based design accords with ergonomics, avoiding fatigue after long time working.

high speed, high efficiency, deep enough, slightly deformation, small heat effect area, high welding quality, pollution free, environmental friendly

Diamond Edge Polishing System

When using diamond edge polishing, edges on acrylic sheets are moved over sharp, fast-rotating diamonds. Properly done is the result so good that diamond polishing can be compared with cast surfaces. Moreover, the method is relatively inexpensive and can be performed on large batches.

Diamond edge polishing may be used on edges of shelves and signs that have previously been sawn to correct dimensions.

It should be noted that diamond edge polishing is exclusively for straight or sloping sides. Eg. it cannot be used on rounded corners

Special design of carriage where 2" lens or 5" lens both can be used. 5" lens gives you better quality of cutting, if the thickness of material is more than 10mm and 2" lens should be used for cutting media less than 10mm thickness.High quality touch panel display - very easy to usePass through design for long length of work piece in Y-axis directionMachine is provided with foot-mounting legs so that there is no vibration in machine and machine can be adjusted on zero levelAs it is made in India, No waiting period for spare parts & quick service supportMachine is provided with heavy duty compressor which has Air-assist combining adjustable focus systems in coaxial jet air to prevent cutting edge from burning downLaser cut software with window based software enhance cutting speed and angel / curve performanceLaser seals the edges of fabric while cuttingMaximum cutting thickness of acrylic - 20mmHigh quality of chiller unit for better performance and long life of laser tube

Chiller (Included)
1. Compact design, convenient for installation and operation.
2. All refrigeration components are international brand, which can offer good and stable cooling effect.
3. The water cycling system is consisted of stainless steel pump with instant flow and high lift, stainless steel water tank and PVC connectors.
4. Equipped with flow switch which can output protect signal.
5. High and low temperature alarm signal output, which can output normal close signal as options.
6. Digital display temperature controller, with multiple function settings and error alarming.

Overview Of GALAXY: WD

Galaxy WD 500 4 Axis laser welding machine with rotary jig and CNC control system is for welding Intersecting line, involute line, curve, point, the entire column and other arbitary trajectories. It is specialized R&D for precision welding industry with high magnification system and well received by customers.

Application Of GALAXY: WD

Suitable for welding of kettle, vacuum cup, stainless steel bowl, sensor, tungsten wire, high power diode (triode), aluminum alloy, laptop shell, mobile phone battery, door head, zinc alloy artwork.

Capable of welding spot, straight seam, circle, square or any plane graphs drawn by AUTOCAD, or even dimensional graphs.

The Fully automatic multifunction and double edge furring equipment.You can work with all foils (PVC, PET, PO etc.) high class foils as well as veneers or laminates.PVS film can be precisely pressed on uneven surfaces.Dual heater used for consistant heating.Stationary hot room reduces chances for damage to the heater assembly.Auto and manual both operations can be performed.Both side vacuum bed arrangement is possible for mass production.

Laser Fume Ventilator is designed for filtrating hazardous fumes and dusts which is generated in the process of laser processing, like laser cutting / engraving / marking/welding / cladding / coding etc. The main function of them is protecting the health of the employees, keeping the machines performance and decreasing environment pollution. Meantime, it can increase product quality, reduce potentional cost.

New for 2014/15, we are pleased to introduce Mehtas Laser Engravable aluminum sheet on which you can laser beautifully black images on gold, silver, white and silver images on black colour aluminum sheet. It can be widely use for making Signs, Advertising Decoration, Awards, Plaques, Trophies Labels, Nameplates, Electrical Products Panel/Cover, Personalized Metal Gifts etc.