Repair Mortar is a shrinkage compensated mortar composed of sand, special cement, fibres and admixtures which provide exceptional handling characteristics. Uses. Suitable for the repair of concrete facades, spalling, honeycombing, balcony sills, overhangs, soffits, cornices and columns.

Primary uses :

• To repair edges of columns and beams damaged during shuttering.
• To repair ceiling concrete damaged while shuttering. .
• To repair edges at doors and windows.
• To repair general honey combs.

Advantages :

• It becomes hard and achieves high strengths.
• It is non shrink.
• It is easy to use.
• It is economical to use.

It is a high performance, chloride-free water reducing cum Concrete Admixture agent for mortars, concrete and lightweight aggregate mixes. It brings about entrainment of innumerable microscopic air bubbles of suitable size and spacing evenly distributed throughout the matrix. It lowers the surface tension of the mixing water. As a result there is considerable reduction in the amount of mixing water required. The plasticizing nature of air entrainment assists in producing a dense, uniform close textured surface free from gravel nests and honeycombing. It is compatible with all types of cements and avoids efflorescence and bleed in concrete. 
Advantages:It is especially suitable for preparation of concrete and plaster and masonry mortars to be used in marine atmospheres and in marine construction. It can be effectively used as an admixture for concrete prepared at site, ready mix concrete and light aggregate concrete. It is particularly suited for pre-cast industry.

Bitumen Based Coating is a single compound, cold applied, water based high solid, elastomeric, pure acrylic resin based coating on application it forms a water proof elastomeric Seal in the form of monolithic uniform membranes.
Features:Adhere strongly to a wide variety of substrates such as concrete metal, Excellent alongation property.U- V light protection.Prevents growth of mess & Fungus.Use friendly and excellent allogation.Excellent thermal insulation property. 
Application:

• Clean the surface and remove any dust, unsound or contaminated material, loose plaster, oil, paint, grease, corrosion deposits or algae. Where breaking out is not required, roughen the surface and remove any laitance by light scabbling.
• All surface cracks should be filled up with crack fill powder.
• Brush apply two coats on entire surface.

We supply a wide consignment of Metallic Floor Hardeners. Our offered range of these products is made in a way to have abrasion resistant which makes concrete and strong flooring. These hardeners make the flooring concrete thus reducing the repair & maintenance cost.

Features:

• Economical in nature
• Forms thick layer
• Makes concrete flooring durable
• Decreases recurring expenses in repairs
• Application areas:
• Railway Platforms
• Factory Sheds
• Loco Sheds
• Concrete Roads
• Jetty
• Warehouse
• Runways

Our firm is the leading manufacturer of Blaine's Filter Paper. The product is used in cement, ceramic and refractory industries for testing particle size of materials by measuring surface area using Blaine's apparatus. 
Features:

• Long term durability
• Tear resistant
• Accurate pore size

Fiberglass mesh has tensile strength, small elongation (3%), high elasticity and rigidity, large shock resistance, good chemical resistance, small water absorbent, the scale stability, heat resistance are good, low cost, not easy burn and forming glassy beads at high temperature. Black silicone coated fiber glass mesh fabric is also offered by us.
Alkali-resistant fiberglass mesh has excellent properties including water-resistance, alkali-resistance, flexibility, softness and resistance to aging. It is widely used in reinforcing walls, natural marble, plaster board, artificial stone materials and exterior insulation finishing system.
Fiberglass mesh is used as reinforcement for waterproofing for terrace, bathroom, B asement etc and used for Decorative tiles as support to hold the tiles.It is Used after surface treatment, the fibre glass mesh have excellent properties inculding water resistance, alkali resistance, fexibility, softness and resistance to ageing. The products are widely used in wall enchancement, wall thermal insulation, waterproofing and various fiberglass wares such as polyphenyl boards, anti-corrosive boards, heated. This product is very durable, versatile and cost effective.

Rust Remover is a aqueous liquid which removes the rust and forms a protective cover around the reinforcement and other steel members. It is just brush applied on the metal surfaces. It is an essential pretreatment to the rebars.

Advantages:

• Solvent free hence environmentally safe.
• Easily applied by brush.
• Rust removing is done very easily.
• Saving in time.
• Reduces manpower

It is a specially manufactured metallic aggregate admixture with cement and stone/granite chips to provide the hardest surface to floorings and pavement which will remain wear-proof, dustproof, waterproof and oil-proof etc.
By the use of SURFACE HARDENER, the flooring and paving topping can be made hard surface which almost become wear and dust proof. It is ideally suited for use in all types of industrial floors which are subjected to heavy traffic and load movement. It can also withstand the impact load due to movement of heavy load over the floor toping. It does not allow any dampness or absorption of water and easy to clean by washing as the surface remains smooth without any hole or crevice etc.

Tile Cleaning Agent is a multipurpose cleaning liquid useful in several cleaning requirements in house hold as well as construction and civil engineering applications. it is also an excellent cleaning agent for removing concrete and mortar runs from tools, wheelbarrows and concrete mixer drums etc. 
Advantage:

• Liquid hence easy to use.
• Can be diluted up to 1:3 with water hence very economical use.
• No corrosive action on plastics, glass and most base metals.

Cement Retarder is a liquid admixture for concrete based on refined Lignosulphonates and Naphthalene formaldehyde blends. It helps in production of super plasticised and set retarded concrete to enable the delayed pouring of concrete after its production or to get over the problems arising during hot weather concreting. 
Advantages:In hot weather ensures continuous pours resulting in monolithic sound concrete. Improves ultimate strengths significantly. Helps saving in cements in rich mixes.

Polypropylene Fibre are precision cut polypropylene fibres which are used in mortars and in concrete to produce crack free and durable wall plasters, concrete panels and durable floor screeds. Fibres are milky white strands of poly propylene supplied in 6 mm and 12 mm lengths. The smaller 6 mm ones are used in plaster mixes whereas the longer 12 mm ones are used in concrete.

Features:Fibres are used as an additive in mortars for making crack free internal and external plasters of buildings. Fibres are also used as an admixture in floor screed concrete for making crack free and aberration resisting floors. As a secondary reinforcement, in large bays of concrete to get over surface cracks.

Non-Metallic Floor Hardeners is exclusively used for de watering flooring systems. These hardeners are enabled with strong monolithic bond with concrete base which makes them abrasion resistant. With the facilities like nonporous these products also offer high wear bearing capacity to the floors.

Features:

• Offers dense non porous and no slip surface
• Have strong bond with base concrete
• Abrasion resistant
• High wear bearing capacity

Epoxy Tile Joint is Three component / Two component colored epoxy resin based putty recommended for use as joint filling material between different tiles like glazed wall tiles, vitrified, stone, glass tiles etc.

Characteristics:

• Excellent bond with tiles and stones
• Extremely rigid on setting and withstands high degree of wear and tear
• Can withstand mild to moderate cleaning agents (depends on actual chemical composition and concentration)
• Mixed material must be consumed in 30 mints.

We are delivering a premium range of Tile Grout. These grouts are used for jointing the tiles in bathroom, kitchen and all other places and manufactured with the use of high grade chemicals to meet defined quality parameters. More adhesiveness and water resistant nature of the products are the advance features of the products. Our Tile Grouts are easy to use and tested on several parameters. It is a gap filling material between different wall and floor tiles like ceramic, glazed, vitrified, mosaic, glass mosaic and marble tiles etc. 
Characteristics:

• Cementitious, only water to be added
• Available in various shades
• Resistant to stains
• Can withstand normal floor cleaning agents
• Waterproof
• Excellent bond with tiles
• Easy to Clean

Block Jointing mortar is a semi premix high quality mortar for jointing and bonding of AAC blocks, concrete blocks, hollow blocks, clay bricks and fly ash bricks. Block Jointing mortar semi premix consists of cement, graded sand and specialised polymers which combine to give superior strength, water retention and stability. It replaces the conventional method and material of jointing mortar which requires a 12-18 mm thickness with a revolutionary 2-3 mm joint thickness. Block Jointing mortar only requires addition of water before application to prepare the product for use, reducing the hassle of measuring and maintaining various individual elements to create a conventional mortar.

Single Component Acrylic Coating is a heavy duty terrace waterproofing system, composed of specially developed highly elastic & resilient acrylic polymers, properly selected & graded fillers, light fast & weather durable pigments, additives & best quality fungicidal in water medium. It is used as a liquid applied waterproofing membrane for all types of building terraces.
 
Features & Benefits:

• Tough & elastic films provides excellent waterproofing.
• Bridges cracks up to 2 mm width.
• Higher tensile strength, tear resistance & bond strength with cementitious substrates.
• Forms highly elastic & resilient coating so helps to withstand the structural movements.
• Resistant to UV & weather conditions.
• Can by applied by brush & roller easily.

 
Application:Clean the surface to remove all loose particles and any deleterious matter. Repair all cracks, honeycombs and blemishes from the concrete surface. Brush-apply primer on the entire surface liberally. Primer is prepared by diluting one part by volume of material with one volume of water. When the primer coat is just dry apply two undiluted Coats at the time interval of 4-6 hrs.

Acrylic based Polymer Modified Cementitious Flexible Composite coating system. Polymer in conjunction with cement provides properties to combat the shortcomings of plain cement, particularly its poor adhesion properties, low impact strength, low flexural strength and thin section fragility. Polymer  adds to the potential use as well as enhances the properties of cement slurry/ mortar/concrete making them excellent choice for use in new as well as renovation work.
Uses It is used for surface treatment, protecting, waterproofing and repairing concrete and masonry. Waterproofing of basements, toilets, terraces, roofs, swimming pools, water towers etc. General concrete repairs. Protection of concrete against corrosion, salt attack etc.

Features

• Combines a tough, flexible, hard-wearing surface with waterproofing.
• Allows trapped vapour to escape thus preventing peeling and blistering.
• Can be applied in uniform thickness to horizontal and vertical surfaces.
• Develops excellent bond to most building materials.
• Reduces or prevents salt penetration into concrete.
• Is not affected by ultraviolet light or by chemicals ranging from mild acids to strong alkalies.
• Is highly durable in continuous wet condition.
• Is non-flammable and does not give off toxic gases, when exposed to fire.
• Will not rot or corrode.
• Most properties improve with age.
• Is not harmful to the health of workman.

Air-entraining s cause small stable bubbles of air to form uniformly through a concrete mix. The bubbles are mostly below 1 mm diameter with a high proportion below 0.3 mm. The benefits of entraining air in the concrete include increased resistance to freeze-thaw degradation, increased cohesion (resulting in less bleed and segregation) and improved compaction in low-workability mixes.

The volume of air entrained depends on the application and the mix design. After mixing, air can be lost during transport and pumping. Allowance should be made for this so that the correct level of air is obtained in the hardened concrete. This may mean testing at the point of discharge rathr than at the batching plant. Air entrainment reduces the density of the mix and increases yield. This needs to be taken into account when batching and mixing.

Concrete curing compound consists essentially of waxes, natural and synthetic resins, and solvents of high volatility at atmospheric temperatures. The compound forms a moisture retentive film shortly after being applied on fresh concrete surface. White or grey pigments are often incorporated to provide heat reflectance, and to make the compound visible on the structure for inspection purpose. Curing compound should not be used on surfaces that are to receive additional concrete, paint, or tile which require a positive bond, unless it has been demonstrated that the membrane can be satisfactorily removed before the subsequent application is made, or that the membrane can serve satisfactorily as a base for the later application.

Naphtha Formaldehyde Based Admixture is a high range, low dosage, super plasticising admixture for slump retention. It is a product based on refined Naphthalene formaldehyde blends. 
Primary Uses:To produce self-compacting flowing concrete.To produce high early strength concrete and for delayed slump retention and for long over hauls.

We offer wide range of Tile Adhesive. Our offered adhesives are highly demanded in all residential and commercial construction work for their adhesive strength and simpler usage. Our organization has highly skilled team of professionals to nurture the demand of the clients. Resistant to water and weather effect. Ready to use grey cement based tile adhesive for wall and floor tile fixing as well as tile on tile application.

Usages:

• Used for fixing ceramic and mosaic tiles on floor and wall surfaces in domestic/commercial buildings
• Must for tile on tile application for repair and rehabilitation works

 
Characteristics:

• Ready to use, only water to be added.
• Contains special chemicals to obtained non-shrink, waterproof and excellent adhesion properties
• Better bond than conventional cement based mortar
• Fast setting and quick strength development
• Self curing
• Good mechanical strength
• Minimum thickness of 3 mm to be maintained using a notched trowel
• Suitable for fixing ceramic and mosaic new tiles on wall and floor
• Must for fixing tile on existing tile without removal of old tiles

We are a leading trader and supplier of high quality Laboratory Filter Paper to our respectable clients. The offered product is processed by trustworthy vendors in complete compliance with international quality standards.

Acrylic Bonding Agent is a water dispersion of grade acrylic latex specifically designed for modifying portland cement compositions. Mortar modified with it has improved physical strength, and superior adhesion to old concrete, masonry, brick, and many other surfaces.

Features/Benefits:

• Improves bond strength
• Increases durability under freeze/thaw cycling
• Reduces cracking through increased mortar flexural strength
• Increases mortar wear resistance under rubber wheeled traffic
• Increases mortar tensile strength
• Repair mortar offers greater impact resistance

Crack filler is a specially formulated polymer modified repair mortar designed to fully meet the requirement of effectively filling cracks in plasters and in concrete, avoiding the use of costly sealants. is a dry powder when mixed with water it forms a creamy consistency paste which is ready for use in filling cracks and repairing plasters. 
Advantages:It is non shrink, hence possibility of shrinkage cracks are non existant. It has high tensile strength and good adhesion property. The finish achieved is sufficiently smooth. Good resistance to freeze / thaw cycles, carbonation and attack by chlorides. Conventional curing is not required.

Epoxy Based Bonding Agent is a Two Component permanent epoxy adhesive for internal or external bonding or rendering, granolithic toppings, and concrete. The ultimate bond strength is greater that the tensile strength of concrete. It does not shrink and provides an even and stress free bond. 
Advantages:

• High strength
• Non shrink
• Durable
• Resistant to chemical attack
• Supplied in pre-weighed units.
• Solvent less epoxy insensitive to moisture

We are offering filter paper. We have been marketing ready to use maxons filter paper 40 blaines circular discs 12.7 +- 0.1 mm dia., having mean pore diameter 7 micron corresponding towhatman 40 for measurement of fineness of cement in variable flow type air permeability apparatus (blaine type). The product is being used by most of the cement manufacturers. We are sure you would also like to use the product for getting consistent, reliable & reproducible results in your quality & process control systems.

We are offering filter paper, we have been marketing ready to use maxons filter paper 40 blaines circular discs 12.7 +- 0.1 mm dia., having mean pore diameter 7 micron corresponding towhatman 40 for measurement of fineness of cement in variable flow type air permeability apparatus (blaine type). The product is being used by most of the cement manufacturers. we are sure you would also like to use the product for getting consistent, reliable & reproducible results in your quality & process control systems.

Micro Concrete is a ready to use dry powder which requires only addition of clean water at site to produce a free flowing non shrink repair micro concrete. It is composed of good quality cement, properly selected aggregates & additives. It is used & designed for repairing of damaged reinforced concrete elements like columns, beams & structure where the areas are restricted or not easily accessible for proper placement of concrete using vibrator. Micro Concrete has excellent flowability, workability & proper particle size to reach small & congested reinforcement.

Our firm is the leading manufacturer of Blaine's Filter Paper. The product is used in cement, ceramic and refractory industries for testing particle size of materials by measuring surface area using Blaine's apparatus.

Plugging Mortar is a quick setting cement sand mortar supplied in dry powder form. This constitutes a blend of cements, graded sand and chemical set control agents. The product needs only on site addition of required amount of water just before its use.

Repair Mortar is a shrinkage compensated mortar composed of sand, special cement, fibres and admixtures which provide exceptional handling characteristics. Uses. Suitable for the repair of concrete facades, spalling, honeycombing, balcony sills, overhangs, soffits, cornices and columns.

Primary uses :

• To repair edges of columns and beams damaged during shuttering.
• To repair ceiling concrete damaged while shuttering. .
• To repair edges at doors and windows.
• To repair general honey combs.

Advantages :

• It becomes hard and achieves high strengths.
• It is non shrink.
• It is easy to use.
• It is economical to use.

It is a high performance, chloride-free water reducing cum Concrete Admixture agent for mortars, concrete and lightweight aggregate mixes. It brings about entrainment of innumerable microscopic air bubbles of suitable size and spacing evenly distributed throughout the matrix. It lowers the surface tension of the mixing water. As a result there is considerable reduction in the amount of mixing water required. The plasticizing nature of air entrainment assists in producing a dense, uniform close textured surface free from gravel nests and honeycombing. It is compatible with all types of cements and avoids efflorescence and bleed in concrete. 
Advantages:It is especially suitable for preparation of concrete and plaster and masonry mortars to be used in marine atmospheres and in marine construction. It can be effectively used as an admixture for concrete prepared at site, ready mix concrete and light aggregate concrete. It is particularly suited for pre-cast industry.

Bitumen Based Coating is a single compound, cold applied, water based high solid, elastomeric, pure acrylic resin based coating on application it forms a water proof elastomeric Seal in the form of monolithic uniform membranes.
Features:Adhere strongly to a wide variety of substrates such as concrete metal, Excellent alongation property.U- V light protection.Prevents growth of mess & Fungus.Use friendly and excellent allogation.Excellent thermal insulation property. 
Application:

• Clean the surface and remove any dust, unsound or contaminated material, loose plaster, oil, paint, grease, corrosion deposits or algae. Where breaking out is not required, roughen the surface and remove any laitance by light scabbling.
• All surface cracks should be filled up with crack fill powder.
• Brush apply two coats on entire surface.

We supply a wide consignment of Metallic Floor Hardeners. Our offered range of these products is made in a way to have abrasion resistant which makes concrete and strong flooring. These hardeners make the flooring concrete thus reducing the repair & maintenance cost.

Features:

• Economical in nature
• Forms thick layer
• Makes concrete flooring durable
• Decreases recurring expenses in repairs
• Application areas:
• Railway Platforms
• Factory Sheds
• Loco Sheds
• Concrete Roads
• Jetty
• Warehouse
• Runways

Our firm is the leading manufacturer of Blaine's Filter Paper. The product is used in cement, ceramic and refractory industries for testing particle size of materials by measuring surface area using Blaine's apparatus. 
Features:

• Long term durability
• Tear resistant
• Accurate pore size

Fiberglass mesh has tensile strength, small elongation (3%), high elasticity and rigidity, large shock resistance, good chemical resistance, small water absorbent, the scale stability, heat resistance are good, low cost, not easy burn and forming glassy beads at high temperature. Black silicone coated fiber glass mesh fabric is also offered by us.
Alkali-resistant fiberglass mesh has excellent properties including water-resistance, alkali-resistance, flexibility, softness and resistance to aging. It is widely used in reinforcing walls, natural marble, plaster board, artificial stone materials and exterior insulation finishing system.
Fiberglass mesh is used as reinforcement for waterproofing for terrace, bathroom, B asement etc and used for Decorative tiles as support to hold the tiles.It is Used after surface treatment, the fibre glass mesh have excellent properties inculding water resistance, alkali resistance, fexibility, softness and resistance to ageing. The products are widely used in wall enchancement, wall thermal insulation, waterproofing and various fiberglass wares such as polyphenyl boards, anti-corrosive boards, heated. This product is very durable, versatile and cost effective.

Rust Remover is a aqueous liquid which removes the rust and forms a protective cover around the reinforcement and other steel members. It is just brush applied on the metal surfaces. It is an essential pretreatment to the rebars.

Advantages:

• Solvent free hence environmentally safe.
• Easily applied by brush.
• Rust removing is done very easily.
• Saving in time.
• Reduces manpower

It is a specially manufactured metallic aggregate admixture with cement and stone/granite chips to provide the hardest surface to floorings and pavement which will remain wear-proof, dustproof, waterproof and oil-proof etc.
By the use of SURFACE HARDENER, the flooring and paving topping can be made hard surface which almost become wear and dust proof. It is ideally suited for use in all types of industrial floors which are subjected to heavy traffic and load movement. It can also withstand the impact load due to movement of heavy load over the floor toping. It does not allow any dampness or absorption of water and easy to clean by washing as the surface remains smooth without any hole or crevice etc.

Tile Cleaning Agent is a multipurpose cleaning liquid useful in several cleaning requirements in house hold as well as construction and civil engineering applications. it is also an excellent cleaning agent for removing concrete and mortar runs from tools, wheelbarrows and concrete mixer drums etc. 
Advantage:

• Liquid hence easy to use.
• Can be diluted up to 1:3 with water hence very economical use.
• No corrosive action on plastics, glass and most base metals.

Cement Retarder is a liquid admixture for concrete based on refined Lignosulphonates and Naphthalene formaldehyde blends. It helps in production of super plasticised and set retarded concrete to enable the delayed pouring of concrete after its production or to get over the problems arising during hot weather concreting. 
Advantages:In hot weather ensures continuous pours resulting in monolithic sound concrete. Improves ultimate strengths significantly. Helps saving in cements in rich mixes.

Polypropylene Fibre are precision cut polypropylene fibres which are used in mortars and in concrete to produce crack free and durable wall plasters, concrete panels and durable floor screeds. Fibres are milky white strands of poly propylene supplied in 6 mm and 12 mm lengths. The smaller 6 mm ones are used in plaster mixes whereas the longer 12 mm ones are used in concrete.

Features:Fibres are used as an additive in mortars for making crack free internal and external plasters of buildings. Fibres are also used as an admixture in floor screed concrete for making crack free and aberration resisting floors. As a secondary reinforcement, in large bays of concrete to get over surface cracks.

Non-Metallic Floor Hardeners is exclusively used for de watering flooring systems. These hardeners are enabled with strong monolithic bond with concrete base which makes them abrasion resistant. With the facilities like nonporous these products also offer high wear bearing capacity to the floors.

Features:

• Offers dense non porous and no slip surface
• Have strong bond with base concrete
• Abrasion resistant
• High wear bearing capacity

Epoxy Tile Joint is Three component / Two component colored epoxy resin based putty recommended for use as joint filling material between different tiles like glazed wall tiles, vitrified, stone, glass tiles etc.

Characteristics:

• Excellent bond with tiles and stones
• Extremely rigid on setting and withstands high degree of wear and tear
• Can withstand mild to moderate cleaning agents (depends on actual chemical composition and concentration)
• Mixed material must be consumed in 30 mints.

We are delivering a premium range of Tile Grout. These grouts are used for jointing the tiles in bathroom, kitchen and all other places and manufactured with the use of high grade chemicals to meet defined quality parameters. More adhesiveness and water resistant nature of the products are the advance features of the products. Our Tile Grouts are easy to use and tested on several parameters. It is a gap filling material between different wall and floor tiles like ceramic, glazed, vitrified, mosaic, glass mosaic and marble tiles etc. 
Characteristics:

• Cementitious, only water to be added
• Available in various shades
• Resistant to stains
• Can withstand normal floor cleaning agents
• Waterproof
• Excellent bond with tiles
• Easy to Clean

Block Jointing mortar is a semi premix high quality mortar for jointing and bonding of AAC blocks, concrete blocks, hollow blocks, clay bricks and fly ash bricks. Block Jointing mortar semi premix consists of cement, graded sand and specialised polymers which combine to give superior strength, water retention and stability. It replaces the conventional method and material of jointing mortar which requires a 12-18 mm thickness with a revolutionary 2-3 mm joint thickness. Block Jointing mortar only requires addition of water before application to prepare the product for use, reducing the hassle of measuring and maintaining various individual elements to create a conventional mortar.

Single Component Acrylic Coating is a heavy duty terrace waterproofing system, composed of specially developed highly elastic & resilient acrylic polymers, properly selected & graded fillers, light fast & weather durable pigments, additives & best quality fungicidal in water medium. It is used as a liquid applied waterproofing membrane for all types of building terraces.
 
Features & Benefits:

• Tough & elastic films provides excellent waterproofing.
• Bridges cracks up to 2 mm width.
• Higher tensile strength, tear resistance & bond strength with cementitious substrates.
• Forms highly elastic & resilient coating so helps to withstand the structural movements.
• Resistant to UV & weather conditions.
• Can by applied by brush & roller easily.

 
Application:Clean the surface to remove all loose particles and any deleterious matter. Repair all cracks, honeycombs and blemishes from the concrete surface. Brush-apply primer on the entire surface liberally. Primer is prepared by diluting one part by volume of material with one volume of water. When the primer coat is just dry apply two undiluted Coats at the time interval of 4-6 hrs.

Acrylic based Polymer Modified Cementitious Flexible Composite coating system. Polymer in conjunction with cement provides properties to combat the shortcomings of plain cement, particularly its poor adhesion properties, low impact strength, low flexural strength and thin section fragility. Polymer  adds to the potential use as well as enhances the properties of cement slurry/ mortar/concrete making them excellent choice for use in new as well as renovation work.
Uses It is used for surface treatment, protecting, waterproofing and repairing concrete and masonry. Waterproofing of basements, toilets, terraces, roofs, swimming pools, water towers etc. General concrete repairs. Protection of concrete against corrosion, salt attack etc.

Features

• Combines a tough, flexible, hard-wearing surface with waterproofing.
• Allows trapped vapour to escape thus preventing peeling and blistering.
• Can be applied in uniform thickness to horizontal and vertical surfaces.
• Develops excellent bond to most building materials.
• Reduces or prevents salt penetration into concrete.
• Is not affected by ultraviolet light or by chemicals ranging from mild acids to strong alkalies.
• Is highly durable in continuous wet condition.
• Is non-flammable and does not give off toxic gases, when exposed to fire.
• Will not rot or corrode.
• Most properties improve with age.
• Is not harmful to the health of workman.

Air-entraining s cause small stable bubbles of air to form uniformly through a concrete mix. The bubbles are mostly below 1 mm diameter with a high proportion below 0.3 mm. The benefits of entraining air in the concrete include increased resistance to freeze-thaw degradation, increased cohesion (resulting in less bleed and segregation) and improved compaction in low-workability mixes.

The volume of air entrained depends on the application and the mix design. After mixing, air can be lost during transport and pumping. Allowance should be made for this so that the correct level of air is obtained in the hardened concrete. This may mean testing at the point of discharge rathr than at the batching plant. Air entrainment reduces the density of the mix and increases yield. This needs to be taken into account when batching and mixing.

Concrete curing compound consists essentially of waxes, natural and synthetic resins, and solvents of high volatility at atmospheric temperatures. The compound forms a moisture retentive film shortly after being applied on fresh concrete surface. White or grey pigments are often incorporated to provide heat reflectance, and to make the compound visible on the structure for inspection purpose. Curing compound should not be used on surfaces that are to receive additional concrete, paint, or tile which require a positive bond, unless it has been demonstrated that the membrane can be satisfactorily removed before the subsequent application is made, or that the membrane can serve satisfactorily as a base for the later application.

Naphtha Formaldehyde Based Admixture is a high range, low dosage, super plasticising admixture for slump retention. It is a product based on refined Naphthalene formaldehyde blends. 
Primary Uses:To produce self-compacting flowing concrete.To produce high early strength concrete and for delayed slump retention and for long over hauls.

We offer wide range of Tile Adhesive. Our offered adhesives are highly demanded in all residential and commercial construction work for their adhesive strength and simpler usage. Our organization has highly skilled team of professionals to nurture the demand of the clients. Resistant to water and weather effect. Ready to use grey cement based tile adhesive for wall and floor tile fixing as well as tile on tile application.

Usages:

• Used for fixing ceramic and mosaic tiles on floor and wall surfaces in domestic/commercial buildings
• Must for tile on tile application for repair and rehabilitation works

 
Characteristics:

• Ready to use, only water to be added.
• Contains special chemicals to obtained non-shrink, waterproof and excellent adhesion properties
• Better bond than conventional cement based mortar
• Fast setting and quick strength development
• Self curing
• Good mechanical strength
• Minimum thickness of 3 mm to be maintained using a notched trowel
• Suitable for fixing ceramic and mosaic new tiles on wall and floor
• Must for fixing tile on existing tile without removal of old tiles

We are a leading trader and supplier of high quality Laboratory Filter Paper to our respectable clients. The offered product is processed by trustworthy vendors in complete compliance with international quality standards.

Acrylic Bonding Agent is a water dispersion of grade acrylic latex specifically designed for modifying portland cement compositions. Mortar modified with it has improved physical strength, and superior adhesion to old concrete, masonry, brick, and many other surfaces.

Features/Benefits:

• Improves bond strength
• Increases durability under freeze/thaw cycling
• Reduces cracking through increased mortar flexural strength
• Increases mortar wear resistance under rubber wheeled traffic
• Increases mortar tensile strength
• Repair mortar offers greater impact resistance

Crack filler is a specially formulated polymer modified repair mortar designed to fully meet the requirement of effectively filling cracks in plasters and in concrete, avoiding the use of costly sealants. is a dry powder when mixed with water it forms a creamy consistency paste which is ready for use in filling cracks and repairing plasters. 
Advantages:It is non shrink, hence possibility of shrinkage cracks are non existant. It has high tensile strength and good adhesion property. The finish achieved is sufficiently smooth. Good resistance to freeze / thaw cycles, carbonation and attack by chlorides. Conventional curing is not required.

Epoxy Based Bonding Agent is a Two Component permanent epoxy adhesive for internal or external bonding or rendering, granolithic toppings, and concrete. The ultimate bond strength is greater that the tensile strength of concrete. It does not shrink and provides an even and stress free bond. 
Advantages:

• High strength
• Non shrink
• Durable
• Resistant to chemical attack
• Supplied in pre-weighed units.
• Solvent less epoxy insensitive to moisture

We are offering filter paper. We have been marketing ready to use maxons filter paper 40 blaines circular discs 12.7 +- 0.1 mm dia., having mean pore diameter 7 micron corresponding towhatman 40 for measurement of fineness of cement in variable flow type air permeability apparatus (blaine type). The product is being used by most of the cement manufacturers. We are sure you would also like to use the product for getting consistent, reliable & reproducible results in your quality & process control systems.

We are offering filter paper, we have been marketing ready to use maxons filter paper 40 blaines circular discs 12.7 +- 0.1 mm dia., having mean pore diameter 7 micron corresponding towhatman 40 for measurement of fineness of cement in variable flow type air permeability apparatus (blaine type). The product is being used by most of the cement manufacturers. we are sure you would also like to use the product for getting consistent, reliable & reproducible results in your quality & process control systems.

Micro Concrete is a ready to use dry powder which requires only addition of clean water at site to produce a free flowing non shrink repair micro concrete. It is composed of good quality cement, properly selected aggregates & additives. It is used & designed for repairing of damaged reinforced concrete elements like columns, beams & structure where the areas are restricted or not easily accessible for proper placement of concrete using vibrator. Micro Concrete has excellent flowability, workability & proper particle size to reach small & congested reinforcement.

Our firm is the leading manufacturer of Blaine's Filter Paper. The product is used in cement, ceramic and refractory industries for testing particle size of materials by measuring surface area using Blaine's apparatus.

Plugging Mortar is a quick setting cement sand mortar supplied in dry powder form. This constitutes a blend of cements, graded sand and chemical set control agents. The product needs only on site addition of required amount of water just before its use.