We are offering forced draft tray dryer(mt-17). the set-up is designed to demonstrate and stimulate the moisture removal by heat under forced draft action created by hot air stream. the set-up consists of an insulated double wall chamber. Inside the chamber a tray is attached directly to an electronic weighing balance, which is fitted on top outside the chamber. Material for drying is placed in the tray and regular loss of weight is monitored. Air from blower passes through heating chamber to produce hot air works as the drying agent entered from one side of the chamber and leave the chamber from other side removes the moisture from the tray. An arrangement is made to vary and measure the airflow rate. A digital temperature controller is used to control and measure the temperature of air stream. >experimentsdetermination of rate of drying of wet sawdust under different conditions of temperature and air flowfeaturessuperb painted structuresimple to operate & maintaincompact & stand alone set uputilities requiredelectric supplyprovide 230 +/- 10 vac, 50 hz, single phase electric supply with proper earthing. 5a, three pin socket with switch for weighing scale, 15a, three pin socket with switch for heatermaterialsaw dust @ 1kg. anemometer air flow measurement

We are offering rotary dryer(mt-19). The set-up is designed to demonstrate and stimulate the moisture removal by heat under forced draft action created by hot air stream and shower of moist solid due to rotary action of dryer drum. The set-up consists of a long cylindrical shell slightly inclined towards the outlet rotating at low rpm. Counter current hot air from blower passes through heating chamber to produce hot air works as the drying agent entered from one side of the rotating shell and leave from other side removes the moisture from the moist solids. High moisture content feed enters from one end of the shell and low moisture content product discharges from the other end of shell. As the shell rotates internal flights lift the solids and shower them down through the interior of the shell. This action increases the contact of wet solid against hot-air making the dryer very effective. An arrangement is made to vary and measure the airflow rate. A digital temperature controller is used to control and measure the temperature of air streamexperimentsto study the operation of a rotary dryerto study the drying characteristics of a solid material under batch drying condition in a rotary dryerfeaturessuperb painted structuresimple to operate & maintaincompact & stand alone set uputilities requiredelectric supplyprovide 230 +/- 10 vac, 50 hz, single phase electric supply with proper earthing. 5a, three pin socket with switch for weighing scale, 15a, three pin socket with switch for heatermaterialsaw dust @ 1kg. Granular and free flowing solid of size I - 2 mmanemometer air flow measurement

The set-up is designed to demonstrate and stimulate the moisture removal by heat under forced draft action created by hot air stream and fluidization property of solid to dry.

The set-up consists of a specially designed, vertical Column. The lower conical portion of the column is filled with moist solids. The material is supported on the screen mesh held between two flanges. Air from blower passes through heating chamber to produce hot air works as the drying agent entered from lower side of the column and leave the column from top outlet removes the moisture of solids. At the top outlet of column a cyclone is provided to collect the solid particles taken out by the air stream. An arrangement is made to vary and measure the airflow rate. A digital temperature controller is used to control and measure the temperature of air stream

Experiments

• To study the fluidized bed drying

Features

• Superb Painted structure
• Simple to operate & maintain
• Compact & stand alone set up

Utilities Required

• Electric supplyProvide 230 +/- 10 VAC, 50 Hz, single phase electric supply with proper earthing. 5A, three pin socket with switch for weighing scale, 15A, three pin socket with switch for heater
• MaterialSaw dust @ 1Kg. Granular and free flowing solid of size I - 2 mm
• AnemometerAir flow measurement

The set-up is designed to demonstrate and stimulate the moisture removal by heat under forced draft action created by hot air stream.

The set-up consists of an insulated double wall chamber. Inside the chamber a tray is attached directly to an electronic weighing balance, which is fitted on top outside the chamber. Material for drying is placed in the tray and regular loss of weight is monitored. Air from blower passes through heating chamber to produce hot air works as the drying agent entered from one side of the chamber and leave the chamber from other side removes the moisture from the tray. An arrangement is made to vary and measure the airflow rate. A digital temperature controller is used to control and measure the temperature of air stream.

>Experiments

• Determination of rate of drying of wet sawdust under different conditions of temperature and air flow

Features

• Superb Painted structure
• Simple to operate & maintain
• Compact & stand alone set up

Utilities Required

• Electric supplyProvide 230 +/- 10 VAC, 50 Hz, single phase electric supply with proper earthing. 5A, three pin socket with switch for weighing scale, 15A, three pin socket with switch for heater
• MaterialSaw dust @ 1Kg.
• AnemometerAir flow measurement

The set-up is designed to demonstrate and stimulate the moisture removal by heat under forced draft action created by hot air stream and shower of moist solid due to rotary action of dryer drum.

The set-up consists of a long cylindrical shell slightly inclined towards the outlet rotating at low RPM. Counter current hot air from blower passes through heating chamber to produce hot air works as the drying agent entered from one side of the rotating shell and leave from other side removes the moisture from the moist solids. High moisture content feed enters from one end of the shell and low moisture content product discharges from the other end of shell. As the shell rotates internal flights lift the solids and shower them down through the interior of the shell. This action increases the contact of wet solid against hot-air making the dryer very effective.

An arrangement is made to vary and measure the airflow rate. A digital temperature controller is used to control and measure the temperature of air stream

Experiments

• To study the operation of a Rotary Dryer
• To study the drying characteristics of a solid material under batch drying condition in a rotary dryer

Features

• Superb Painted structure
• Simple to operate & maintain
• Compact & stand alone set up

Utilities Required

• Electric supplyProvide 230 +/- 10 VAC, 50 Hz, single phase electric supply with proper earthing. 5A, three pin socket with switch for weighing scale, 15A, three pin socket with switch for heater
• MaterialSaw dust @ 1Kg. Granular and free flowing solid of size I - 2 mm
• AnemometerAir flow measurement

The set-up is designed to demonstrate and stimulate the moisture removal by heat under natural draft action created by hot air stream.

The set-up consists of an insulated double wall chamber. Inside the chamber a tray is attached directly to an electronic weighing balance, which is fitted on top outside the chamber. Material for drying is placed in the tray and regular loss of weight is monitored. Air works as the drying agent by natural action removes the moisture from the tray by passing towards the top openings. A digital temperature controller is used to control and measure the temperature of air stream l

Experiments

• Determination of rate of drying of wet sawdust under different conditions of temperature

Features

• Superb Painted structure
• Simple to operate & maintain
• Compact & stand alone set up

Utilities Required

• Electric supplyProvide 230 +/- 10 VAC, 50 Hz, single phase electric supply with proper earthing. 5A, three pin socket with switch for weighing scale, 15A, three pin socket with switch for heater
• MaterialSaw dust @ 1Kg.
• Support tableSize: 500Wx500Dx750H in mm

We are offering forced draft tray dryer(mt-17). the set-up is designed to demonstrate and stimulate the moisture removal by heat under forced draft action created by hot air stream. the set-up consists of an insulated double wall chamber. Inside the chamber a tray is attached directly to an electronic weighing balance, which is fitted on top outside the chamber. Material for drying is placed in the tray and regular loss of weight is monitored. Air from blower passes through heating chamber to produce hot air works as the drying agent entered from one side of the chamber and leave the chamber from other side removes the moisture from the tray. An arrangement is made to vary and measure the airflow rate. A digital temperature controller is used to control and measure the temperature of air stream. >experimentsdetermination of rate of drying of wet sawdust under different conditions of temperature and air flowfeaturessuperb painted structuresimple to operate & maintaincompact & stand alone set uputilities requiredelectric supplyprovide 230 +/- 10 vac, 50 hz, single phase electric supply with proper earthing. 5a, three pin socket with switch for weighing scale, 15a, three pin socket with switch for heatermaterialsaw dust @ 1kg. anemometer air flow measurement

We are offering rotary dryer(mt-19). The set-up is designed to demonstrate and stimulate the moisture removal by heat under forced draft action created by hot air stream and shower of moist solid due to rotary action of dryer drum. The set-up consists of a long cylindrical shell slightly inclined towards the outlet rotating at low rpm. Counter current hot air from blower passes through heating chamber to produce hot air works as the drying agent entered from one side of the rotating shell and leave from other side removes the moisture from the moist solids. High moisture content feed enters from one end of the shell and low moisture content product discharges from the other end of shell. As the shell rotates internal flights lift the solids and shower them down through the interior of the shell. This action increases the contact of wet solid against hot-air making the dryer very effective. An arrangement is made to vary and measure the airflow rate. A digital temperature controller is used to control and measure the temperature of air streamexperimentsto study the operation of a rotary dryerto study the drying characteristics of a solid material under batch drying condition in a rotary dryerfeaturessuperb painted structuresimple to operate & maintaincompact & stand alone set uputilities requiredelectric supplyprovide 230 +/- 10 vac, 50 hz, single phase electric supply with proper earthing. 5a, three pin socket with switch for weighing scale, 15a, three pin socket with switch for heatermaterialsaw dust @ 1kg. Granular and free flowing solid of size I - 2 mmanemometer air flow measurement

The set-up is designed to demonstrate and stimulate the moisture removal by heat under forced draft action created by hot air stream and fluidization property of solid to dry.

The set-up consists of a specially designed, vertical Column. The lower conical portion of the column is filled with moist solids. The material is supported on the screen mesh held between two flanges. Air from blower passes through heating chamber to produce hot air works as the drying agent entered from lower side of the column and leave the column from top outlet removes the moisture of solids. At the top outlet of column a cyclone is provided to collect the solid particles taken out by the air stream. An arrangement is made to vary and measure the airflow rate. A digital temperature controller is used to control and measure the temperature of air stream

Experiments

• To study the fluidized bed drying

Features

• Superb Painted structure
• Simple to operate & maintain
• Compact & stand alone set up

Utilities Required

• Electric supplyProvide 230 +/- 10 VAC, 50 Hz, single phase electric supply with proper earthing. 5A, three pin socket with switch for weighing scale, 15A, three pin socket with switch for heater
• MaterialSaw dust @ 1Kg. Granular and free flowing solid of size I - 2 mm
• AnemometerAir flow measurement

The set-up is designed to demonstrate and stimulate the moisture removal by heat under forced draft action created by hot air stream.

The set-up consists of an insulated double wall chamber. Inside the chamber a tray is attached directly to an electronic weighing balance, which is fitted on top outside the chamber. Material for drying is placed in the tray and regular loss of weight is monitored. Air from blower passes through heating chamber to produce hot air works as the drying agent entered from one side of the chamber and leave the chamber from other side removes the moisture from the tray. An arrangement is made to vary and measure the airflow rate. A digital temperature controller is used to control and measure the temperature of air stream.

>Experiments

• Determination of rate of drying of wet sawdust under different conditions of temperature and air flow

Features

• Superb Painted structure
• Simple to operate & maintain
• Compact & stand alone set up

Utilities Required

• Electric supplyProvide 230 +/- 10 VAC, 50 Hz, single phase electric supply with proper earthing. 5A, three pin socket with switch for weighing scale, 15A, three pin socket with switch for heater
• MaterialSaw dust @ 1Kg.
• AnemometerAir flow measurement

The set-up is designed to demonstrate and stimulate the moisture removal by heat under forced draft action created by hot air stream and shower of moist solid due to rotary action of dryer drum.

The set-up consists of a long cylindrical shell slightly inclined towards the outlet rotating at low RPM. Counter current hot air from blower passes through heating chamber to produce hot air works as the drying agent entered from one side of the rotating shell and leave from other side removes the moisture from the moist solids. High moisture content feed enters from one end of the shell and low moisture content product discharges from the other end of shell. As the shell rotates internal flights lift the solids and shower them down through the interior of the shell. This action increases the contact of wet solid against hot-air making the dryer very effective.

An arrangement is made to vary and measure the airflow rate. A digital temperature controller is used to control and measure the temperature of air stream

Experiments

• To study the operation of a Rotary Dryer
• To study the drying characteristics of a solid material under batch drying condition in a rotary dryer

Features

• Superb Painted structure
• Simple to operate & maintain
• Compact & stand alone set up

Utilities Required

• Electric supplyProvide 230 +/- 10 VAC, 50 Hz, single phase electric supply with proper earthing. 5A, three pin socket with switch for weighing scale, 15A, three pin socket with switch for heater
• MaterialSaw dust @ 1Kg. Granular and free flowing solid of size I - 2 mm
• AnemometerAir flow measurement

The set-up is designed to demonstrate and stimulate the moisture removal by heat under natural draft action created by hot air stream.

The set-up consists of an insulated double wall chamber. Inside the chamber a tray is attached directly to an electronic weighing balance, which is fitted on top outside the chamber. Material for drying is placed in the tray and regular loss of weight is monitored. Air works as the drying agent by natural action removes the moisture from the tray by passing towards the top openings. A digital temperature controller is used to control and measure the temperature of air stream l

Experiments

• Determination of rate of drying of wet sawdust under different conditions of temperature

Features

• Superb Painted structure
• Simple to operate & maintain
• Compact & stand alone set up

Utilities Required

• Electric supplyProvide 230 +/- 10 VAC, 50 Hz, single phase electric supply with proper earthing. 5A, three pin socket with switch for weighing scale, 15A, three pin socket with switch for heater
• MaterialSaw dust @ 1Kg.
• Support tableSize: 500Wx500Dx750H in mm