Dear Sir,

This is a small introduction of me. Basically I am an Electrical & Electronics engineer and an Ex-Engineer of Electrotherm (I) Limited. I am having experience of more than 12 years in this field and a GATE qualified candidate in the year 2003.I have started my own business in the year of 2007 with a very limited no. of products. But now I am running a well equipped factory near Alstom factory, Durgapur (W.B). Where I am manufacturing and supplying all the essential items used in any Induction furnace. Beside this I am doing consultancy in Steel Plants also (Electrical or Mechanical, nutral ramming mass etc).A brief description of the materials are given below –

A. Scope of supply

1. Inverter thyrister
2. Converter thyrister
3. HRC Fuses
4. Feed Back Fuse
5. Mica sheet
6. Round Mica
7. Carbon Free Hose Pipe (12mm – 100mm)
8. Syndhania segment
9. Syndhania spacer
10. Glass tape
11. Dr. Beck varnish
12. Brake Thruster
13. Resistance box
14. S.S Cooling turn
15. FRP sheet
16. Copper tube
17. Flexocoat Hardner & Base
18. MF capacitor (5450kvar/700Hz/3000V)
19. Water cooled Resistances used in panel
20. Sharing capacitors used in panel
21. Temperature tips
22. Volt meter, Ampere meter, KW meter
And many more item

B. List of material manufactured and repaired as per order –

1. Lamination yoke
2. Water cooled cable
3. Change over switch
4. S.S Cooling turn
5. Top & Bottom set
6. Power factor improvement equipment. (To improve power factor)
7. Load manager for Induction furnace. (To improve load factor)
8. Power optimizer etc.
9. Coil cradle for any furnace.
10. Nutral ramming mass from DFP Germany.
11. Lining vibrater to maximize the no of lining or patching heat.



We are supplying many more item than the list given above. At last I hope you will go through it very seriously and give us an opportunity to give you a service better than others.
Manufacturing of Induction spare parts,consultancy on Induction Furnace.Manufacturing of Sambrani/Dhuna Dhup etc.

Dear Sir,

This is a small introduction of me. Basically I am an Electrical & Electronics engineer and an Ex-Engineer of Electrotherm (I) Limited. I am having experience of more than 12 years in this field and a GATE qualified candidate in the year 2003.I have started my own business in the year of 2007 with a very limited no. of products. But now I am running a well equipped factory near Alstom factory, Durgapur (W.B). Where I am manufacturing and supplying all the essential items used in any Induction furnace. Beside this I am doing consultancy in Steel Plants also (Electrical or Mechanical, nutral ramming mass etc).A brief description of the materials are given below –

A. Scope of supply

1. Inverter thyrister
2. Converter thyrister
3. HRC Fuses
4. Feed Back Fuse
5. Mica sheet
6. Round Mica
7. Carbon Free Hose Pipe (12mm – 100mm)
8. Syndhania segment
9. Syndhania spacer
10. Glass tape
11. Dr. Beck varnish
12. Brake Thruster
13. Resistance box
14. S.S Cooling turn
15. FRP sheet
16. Copper tube
17. Flexocoat Hardner & Base
18. MF capacitor (5450kvar/700Hz/3000V)
19. Water cooled Resistances used in panel
20. Sharing capacitors used in panel
21. Temperature tips
22. Volt meter, Ampere meter, KW meter
And many more item

B. List of material manufactured and repaired as per order –

1. Lamination yoke
2. Water cooled cable
3. Change over switch
4. S.S Cooling turn
5. Top & Bottom set
6. Power factor improvement equipment. (To improve power factor)
7. Load manager for Induction furnace. (To improve load factor)
8. Power optimizer etc.
9. Coil cradle for any furnace.
10. Nutral ramming mass from DFP Germany.
11. Lining vibrater to maximize the no of lining or patching heat.



We are supplying many more item than the list given above. At last I hope you will go through it very seriously and give us an opportunity to give you a service better than others.
Manufacturing of Induction spare parts,consultancy on Induction Furnace.Manufacturing of Sambrani/Dhuna Dhup etc.