Lubsa Multilub Systems

NIT, Faridabad, Haryana

Model LM SG-25 LM SG-38 Description Tube dia 25mm. OD, Inlet & Outlet port 1/8 BSP. Tube dia 38mm. OD, Inlet & Outlet port 1/8 BSP.

Supplier & Manufacturer of Nylon & Steel Tubes. Our product range also comprises of Motorised Lubrication Units, Grease Lubrication System and Air-Oil Mist Lubrication System

AKE Off metering injector works on a different principle than the normal metering injectors. Normal metering injector discharge the oil at the ON position of pump. The Take Off injector gets charged at the ON position of pump and the spring loaded piston (indicator pin) ejects out. This injector discharges the oil at the OFF condition of pump and the spring loaded piston (indicator pin) will go back. A non return valve has been provided at each injectors to retain the oil in the injectors. It is available in the different dosages and can be supplied as per customers' requirement.

These valves have been designed for discharge the oil continuously drop by drop under low pressure of 2-4 kg/cm2. The efficiency of these valves are depend upon the purity of oil and viscosity of oil. The viscosity of oil should not be more than 68 cst. These valves can be operated with motorised / pneumatic / manual pump. These valves are available in different input thread size i.e.1/8"B.S.P., 1/8"N.P.T., M8x1 taperetc.and outlet is suitable for4mmOD tube.

Multiline radial lubricator is best suited for machine /plant where lubrication is required with high pressure continuously / intermittently for individual point. This lubricator are used for machine / plant like rolling mill, sugar plant, cement plant, rubber mixing machine, forging hammer, stone crusher, spong iron plant etc. This lubricator comprise of a single pumping station having a number of plunger pump placed radically and fitted on to the outer periphery of the housing. Each plunger unit is given a reciprocating motion with the help of a cam. The cam rotates with the help of an electric motor and speed reduction gear box. The dose per plunger pump / cycle is 0.05 to 0.25cc (adjustable) with maximum pressure 200 Kg/cm2. These all plunger pump are connected to the lubrication point directly / progressive block by mean of tube, rubber hose, compression type fitting, clamping etc. Grease filling in the reservoir can be done manually as well as with the help of other pump. For pump BSP port is provided on reservoir. Always use proper & clean lubricants. Avoid foreign particles in the pump. The foreign particles or dust items are the main responsible factor to damage physical components of the pump and chocking in the plunger body. Always fill the lubricants before it is empty to avoid air in the pump. The presence of air may be resulted in improper quantity of discharge. Should always careful with regular maintenance of plungers and reservoir for its long life. Do not plug out put of any pumping unit.

LHMGFS-5 (Reservoir Cap.-5 Kg.) Discharge-8 gms per stroke, Max. Pr.-100Kg/Cm2, with Rubber hose & grease adopter. LHMGFS-10 (Reservoir Cap.-10 Kg.) Discharge-10 gms per stroke, Max. Pr.-125Kg/Cm2, with Rubber hose & grease adopter. LHMGFS-20 (Reservoir Cap.-20 Kg.) Discharge-10 gms per stroke, Max. Pr.-150Kg/Cm2, with Rubber hose & grease adopter. All above mentioned models are mobile type. The pressure plate or dead weight has been provided in all the models to avoid the air gap. These pumps are suitable for pressurized greasing of machine parts.

LAMGFS-25 (Mobile) Reservoir Cap.-25 Kg. Discharge-300 to400 gms per minute, Max. Pr.-125 Kg/Cm2, with rubber hose, Grease gun & Trolley mounted. LAMGFS-50 (Mobile) Reservoir Cap.-50 Kg. Discharge-300 to 400 gms per minute, Max. Pr.-125 Kg/Cm2, with rubber hose, Grease gun & Trolley mounted. LAMGFS-200 SuitablefordrumCap.-200Kg, Discharge-300 to 400gms per minute, Max. Pr.-150Kg/Cm2, Air input pressure 5-7 Kg/Cm2. With rubber hose & grease gun. This pump is suitable for transfer the grease with greater discharge.

LMGFS-25 (Mobile) Motor0.25HP 1440rpm.440V.AC Three Phase Reservoir Cap.-15 Kg. Discharge-04 Kg per hours, Max. Pr.-125 Kg/Cm2, with Trolley mounted.

Supplier & Manufacturer of 12 24 V DC Radial Lubricator. Our product range also comprises of Motorised Lubrication Units, Grease Lubrication System and Air-Oil Mist Lubrication System.

Model LM B-03 LM B-05/08 Description Used for oil filling cum air breathering in lubricating Units. Used for oil filling cum air breathering in lubricating Units.

Model H LM SS-03 LM SS-05 LM SS-50 Description For 3Ltrs. Motorized lubrication unit. For 5Ltrs./8Ltrs. Motorized lubrication unit. For 10 to 100 Ltrs. Oil recirculating system.

Model LM RV-030-A LM RV-030-B Description Used for pressure setting in Lubricating units. Used for pressure setting in Lubricating units.

Supplier & Manufacturer of PRESSURE SWITCH. Our product range also comprises of Motorised Lubrication Units, Grease Lubrication System and Air-Oil Mist Lubrication System.

Supplier & Manufacturer of FLOAT SWITCH. Our product range also comprises of Motorised Lubrication Units, Grease Lubrication System and Air-Oil Mist Lubrication System.

Progressive distributor blocks of LPB-4555 (Secondary Line) / LPB-6080 (Primary Line) series are meant for distribution of grease/oil delivered by a pump. From this progressive block we get lubricant in sequently one after another. Any one outlet is blocked then the progressive block will stop functioning, with suitable monitoring devices, this blockages is sensed and suitable warning is given to avoid running the machine without proper lubrication. These blocks can be used for intermittent / continuous lubrication.

Automobile Special Purpose Machine are made using good quality raw material. These are used not only in large scale but also in medium industries all over. Their main mostly used for the self-lubricating solutions.

Supplier & Manufacturer of PRESSURE GAUGE. Our product range also comprises of Motorised Lubrication Units, Grease Lubrication System and Air-Oil Mist Lubrication System

Metric Pumps are used in chemical and other industries where fluid translation is required. because it has the ability of exact flow regulating. However, replica watchesits operated with the help of hand wheel in the pump so as to regulate the flow of the pump.

Hydraulic power packs are are designed in a way to meet the requirements to clients. They are supplied in various ranges in terms of pressure and depending upon the flow of its applications

These pumps suitable for manual centeralised lubrication system of light duty automatic automatic machines such as small power presses, packing machines, milling machines, single spindle automats, looms, surface grinders, pouch fillings machines etc. Normally these pumps are suitable for 2-40 lubricant points. These pumps are very simple in construction. The construction is spring return piston type the piston is operated by pulling a cam handle. The other salient features are strainer at the inlet port, a pressure reducing system which is very important for proper operation of metering cartridges. Always fill clean oil to get better life and trouble free operation of these pumps. It is not recommended to operate dry pumps. Pumps are suitable for oil with viscosity range 40-1000 cst.