Lion Industries

GIDC, Mahesana, Gujarat

We are the Manufacturer and Supplier of Ultra Bond Compound from Vijapur in Gujarat.  The ultra bond compound is a blend of modified styrene, butadiene and latex. It is offered as a ready to use bonding agent in liquid form.

 

Areas of applications :

• For concrete repairs – Spalled concrete of floors, columns, beams, chajja, slabs, parapets etc.

• For waterproofing – Small roof terraces, sunken portions of toilets & bathroom, Chajja & lift pits, Balconies.

• As a bond coat- for bonding of new concrete to old concrete, masonry stone work, plastering.

• For cladding – fixing or re-fixing of slip bricks, tiles, stone & marble bedding

• As external rendering – Weatherproof & forst resistant render.

• As bonding slurry coat for pinhole treatment on concrete surface.

 

Feature & Benefits :

• Multipurpose – it is multipurpose & economical product, easy to use.

• Cracking – it prevents cracking by improving flexural strength.

• Hardness – Improves the hardness & prevents dust generation.

• Shrinkage -Reduces drying & aging shrinkage cracks.

• Bonding - Bond strongly to concrete, masonry, stonework, plasters, cementitious surface.

• Erosion & corrosion – Improves erosion resistance & prevents corrosion.

• Abrasion resistance – Improves abrasion resistance of the cement mix.

• Grouting – Reduces viscosity of cement injection grout for better fluidity & bonding

 

Method Applications :

• Surface Preparation :
  • Clean the surface with wire brush or scrubber to remove hidden dirt, loose particles & dust. Degrease the surface by using suitable solvents
  • Repair the spalled concrete portion by saw, cutting the extreme edges of the repair location to a depth of a least 10 mm to avoid feather edging & to provide strong bond
  • Clean the concrete surface to remove any contamination where breaking is not possible. Roughen the surface by light scrabbling or grit blasting
  • For priming of concrete substrate, the surface should be thoroughly saturated with potable water. Remove any excess of water prior to application over any excess of water prior to application.

• Waterproofing Coating :
  • For a waterproofing coating Mix Ultra Bond :cement in the ratio 1:1.5 by volume
  • Mix for 20-3 min. to avoid air entrapment. Keep on slowly adding cement to Ultra Bond until the required consistency is achieved
  • Brush apply 2 coats of the mix in a span of 4-6 hours on the prepared concrete substrate. Overlay the coating with a protective screed to the desired slope & thickness

• Bonding Primer
  • For a bonding primer coat of Ultra Bond mix : Cement in the ratio 1:1.5 by volume
  • Brush apply 1 continuous coat of the mix on the prepared concrete substrate.
  • Ensure to overlay the repair mortar when the bond coat is still tacky

• Repair Mortars & Renders
  • A suitable mix ratio for patching repair mortar or render is as follows :
  • Mix design – Portland Cement :50kg, Washed Sand : 150 kg, Ultra Bond : 6-7.5 kg and Water : 10 lit

• Floor Screeds & PCC
  • A suitable mix ratio for patching repair mortar or render is as follows :
  • Mix design – Portland Cement :50kg, Washed sand :75 kg, 6mm downsize aggregates :
  • 75 kg, Ultra Bond 6-7 Kg water - 10 Lit

• Mixing & Application
  • A forced action mixer is essential (PAN Mixer) & recommended to ensure that Ultra Bond Mortar is thoroughly mixed. Use a suitable Sized drum with heavy – duty electrical drill machine fitted with spiral paddle mixer at slow speed of 400-500rpm.
  • Hand mixing is permissible only for 25 kg or less quality
  • Charge the mixer with required quantity of clean & dry sand (or coarse aggregates as needed), cement & mix for 1.-2 min., then add the recommended dosage of Ultra Bond dispensed in water which is pre – batched. Mix for 2-3 minutes to avoid air entrapment. Keep on slowly adding water until the required consistency is achieved

   

Dosage :

• A a waterproofing coating – Mix proportion by volume; 1:1.5 (Ultra Bond : Cement)

• As a mortar modifier – 10-15% of Ultra Bond by weight of cement

• As a bonding agent – Mix proportion by volume; 1:1 (Ultra Bond : Cement)

 

Packing : 1 Kg, 5 Kg, 10 Kg, 20 Kg and 230 Kg

 

Coverage :

• As a waterproofing coating -22-25sq.ft./kg in 2 coats

• As a mortar modifier – 6-7.5 kg of Ultra Bond per 50 Kg of cement

• As a bonding agent – 45 – 50 sq. ft./Kg per coat

 

Precaution & Limitation :

• Recommended dosage to be followed to achieve desired results.

• When working in hot temp. conditions, extra water may be added to the repair mortar to compensate for the evaporation loss & make the mortar workable

 

Shelf life :

• Best before Two years form the data manufacture when in sealed pack and stored under proper condition.
• Store in a cool & Dry place in unopened conditions away form direct sunlight.

 

Other Products Categories Available : Brings the Widest range of Construction Material & Chemical.

We are the most sought after Manufacturer and Supplier of Premium SBR Latex Compound from Vijapur in Gujarat. This is a Multipurpose SBR Latex Based product For General Repair For Economical Waterproofing.  Some of the most common applications of

 

Areas of Applications :

• As bond coating – Plaster to plaster, concrete to concrete, Plaster over brick masonry.

• As waterproof repair plaster.

• As crack repair – Plaster cracks more than 5 mm, In gaps developed between masonry and RCC members.

• For cladding – Fixing or refixing of slip bricks, tiles, stones & marble

 

Method Applications :

• Surface preparation : All substrates should be cleaned & free of dust, Plaster, oil, paint, grease, corrosion deposits  & any other  laitance. Cleaning should be done by wire brush or other mechanical means.

• Bond agent : Mix Premium Latex, water and cement in 1:4:7 proportion by volume and apply this mix with brush in a single coat over the clean any surface.

• Renders, Patching & crack repair mortar : Mix 5 kg of super latex with 15ltr of water 50 kg cement and 150 kg sand. Fill the crack with above prepared mortar. Compact it into the crack fully an trowel finish to level.

• Waterproof coating : Mix Premium latex, water and cement in 1:4:7 proportion by volume. Apply 1^st coat when the surface is in saturated dry condition and allow it to dry for 4 to 6 hours. Overlay the 2^nd coat with screed / plaster for protection and finish.

 

Coating for 'salt petre' – free plaster brick masonry : Mix Premium Latex, water and cement in 1:4:7 proportion by volume. Brush apply the 1^st coat on brick. Apply 2^nd Coat after 1^st coat is dry. When 2^nd coat is tacky, Place as per instructions

 

Packing : 1 Ltr, 5 Ltr, 10Ltr, 20 Ltr and 230 Ltr

 

Shelf life :

• Best before Two years form the data manufacture when in sealed pack and stored under proper condition.
• Store in a cool & Dry place in unopened conditions away form direct sunlight.

 

Other Products Categories Available : Brings the Widest range of Construction Material & Chemical.

We are one of the major Manufacturer and Supplier of L-Poxy Epoxy Grout from Vijapur in Gujarat. Our L-Poxy Epoxy grout is a 3 part system, where 3 independent components need to be combined together  and is very effective for jointing wall and floor tiles, particularly on surface with high chemical and sets and hardens without contracting.

 

Area of Application : The L- Poxy Epoxy Grout is intended for jointing wall and floor tiles, particularly on surface with high chemical and sets and hardens without contracting.

 

Feature and Benefits :

• Sterile

• Frost-Proof

• Hygienic and chemical resistant stain and bacterial resistant

• High Durable joints

• smooth surface

• Water proof

• High strength

• Non – Contracting

• High abrasion resistant

 

Method Applications :

• Joints should be free from efflorescence, laitance, dirt and other loose material.

• Removal thoroughly by dry brushing.

• Clean :All joints should be cleaned down by washing with water containing detergent, then with clean water.

• Ensure the joints are dry before grouting.

• Before commencing grouting the adhesive bed must be set. It is essential that the titles used are appropriate for the service conditions and are fixed in solid bed of adhesive i.e. ensuring that. As far as possible, no voids are left behind / beneath the tiles. Refer to the relevant product data sheet for setting / drying times.

• Protect open joints form contamination and ensure that they are clean, dry and free form loose debris prior to grouting.

• Do not grout at temp. less than 5C or in damp conditions.

 

Area of Applications :

• Wall

• Exterior

• Work Tops

• Hygienic Sterile Areas

• Floors

• Dry Areas

• Swimming pools

• Chemical Resistance

• Interior

• Wet Areas

• Hevily trafficked Floors

• Hydrotherapy Pools

 

Packing : 1kg and 5kg Available in more than 20 colours.

 

Application Mixing :

• The EPOXY GROUT consistency can be adjusted to suit the application and site conditions by varying the quality of Part C added to the mixed Part A and Part B.

• Before use shake the bottle of Part B and Stir Part A.

• Add all of Part B to all Part A in a suitable, clean container and thoroughly mix together

• If an electrical drill mixer is used, blend at slow speed (less than 300 rpm).

• Slowly add the required amount of Part C and mix until all the Part C has been dispersed and a uniform colour is achieved.

• Immediately pour the mixed grout onto the working area.

• The mixed EPOXY GROUT is usable for up to 45 min. at 27± 1C.

 

Coverage Estimates 

• Pack Size 5kg : Part (A) 1.00 kg, Part (B) 400 g and part 3.6kg

• Pack Size 1kg: Part (A) 180 gm, Part (B) 90 gm and part 730gm Coverage Consumption depend on joint width size of tiles and good workmanship.

 

Precaution & Limitation :

• Keep out of reach of children. Wear suitable protective clothing, gloves and eyes / face protection

• In case of contact with eyes rinse immediately with plenty of clean water and seek medical advice

 

Shelf life :

• Factory sealed bag of this product are guaranteed to be of first quality for Two (2) year* if stored off the ground in a dry area.
• High humidity will reduce the shelf life of bagged product.

 

Other Products Categories Available : Brings the Widest range of Construction Material & Chemical.

We are a well-known Manufacturer and Supplier of Wall Touch Putty from Vijapur in Gujarat. Wall Touch Putty (Wall Putty) is a white cement based polymer modified wall putty specially developed as a finish coat to cover unevenness and pinholes in plastered surfaces and to make the walls / ceilings ready for painting. As it is white, it can be treated as a base coat for painting.

 

Area of Applications : Wall touch specially developed as a finish coat to cover unevenness and pinholes in plastered surface and to make the wall/ceiling ready for painting.

 

Features & Benefits :

• Excellent Whitest putty

• Highly water resistant

• Strong bonding to the base plaster

• Excellent smooth finish

• Excellent workability

• UV Resistance

• True color tone of the paint is maintained, primer is not required

• Protects expensive paint from dampness, peeling off and flaking

• Makes paint durable

• Paint finish is superior

• Suitable for interior as well as exterior

• Reduces paint consumption

• Avoid frequent repainting

• cost effective

• Aesthetic look for ceilings, interior and external walls

• Ease of use at site

 

Method Applications :

• Dampen the surface to be plastered with clean water. Allow excess water to drain off.

• Using a steel trowel/blade, apply the above mix to a thickness of about 0.5-1 mm level and smoothen the surface.

• Apply the second coat 0.5-1 mm after the first coat has fully dried and set. In areas of high temp. and low humidity for two days is recommended.

• The thickness of each coat should not exceed 1mm and total plaster thickness should not exceed 2mm

• Smoothen with a steel trowel, Sand paper if so desired with 600no. Of sand paper

 

Test Result of Wall Touch

• Pot life 115 min

• Whiteness 90% +

• Autoclave expansion Nil

• Workability good.

 

Application Mixing :

• Take 300-400 ml of clean water for 1Kg of WALL TOUCH (Wall putty) in a clean bucket. It is very important that Wall Touch to be Added in water and not vice versa.

• Stir continuously by using an electric mixer or by hand to obtain a homogeneous lump-free paste.

• Allow the resultant paste to stand for about 10 min. for the additives to dissolve

• Re- mix again for about 2 min. the mixture is now ready

• Use the mix within 1Hrs

 

Packing : 20kg, 40kg BOPPE Export quality bag.

 

Coverage : We recommend :

• Maximum two coats (Layers) of Wall Touch.

• Minimum thickness of 1^st coat (Layer) 0.5 to 1mm.

• Maximum thickness of 2^nd coat (Layer) 0.5 to 1mm.

• Total thickness can go up to 1 to 2 mm in 2 Layers.

 

Precaution & Limitation

• Although wall Touch do not contain any toxic material, use rubber gloves while mixing

• Precaution should be taken to avoid dust inhalation while handling putty powder or during removal of application makes with fine emery paper-say wearing nose mask.

• Keep the product out of reach of children.

• Once putty paste has hardened, it shall not be used by adding water.

 

Shelf Life & Storage :

• Factory sealed bag of this product are guaranteed to be fist quality for Six month * if stored off the ground in a dry area.
• Store in a cool & dry in unopened condition away from direct sunlight

 

Other Products Categories Available : Brings the widest range of Construction Material & Chemical.

 We are a unique Manufacturer and Supplier of Tile Adhesive from Vijapur in Gujarat. Tile Adhesive is a Cementatious ready mix powder, which is a thin-bed and highly tensile polymer modified product. It's unique properties make it ideal for fixing ceramic/ vitrified tiles/ mosaic tiles/ natural stone like granite, marble and other heavy stones on floors, walls and ceilings.

 

Areas of Applications : Tile Adhesive mortar is a masonry mortar for use to fix Tiles on Floor, wall, ceiling.

 

Features & Benefits

• Preparation is simple, just add water

• Although cement based, requires no curing. This product is self curing

• It can be used in damp areas.

• Excellent Tensile adhesion strength.

• Grouting is possible on the same day.

• Polymer modified formulation enhance its durability.

• Being ready to use, the product saves considerable time and labour.

• Non – hazardous.

 

Method Applications :

• Easy to Mix and use dry mortar saves water, Sand, Cement & Time.

• Mix the product with water in the ratio of approx. 1:4

• Mixing can be done manually or by stirrer.

• Mixing to be done till homogeneous mix is obtained.

• The Paste should be kept away form direct sunlight, heat and used with in 2 hr. of preparation (after mixing with water)

 

Application Mixing and Placing : Just add 27% - 30% water in 20kg bag.

 

Packing : 20 Kg in BOPP Export Quality Bag. Company also provide Trowel in every bag.

 

Colour : Grey And White

 

Coverage : 30-10 sq. ft per 20Kg with notch trowel for a bed of 3-4 mm.

 

Precaution & Limitation :

• Contains Portland Cement and silica sand. May irritate eyes and skin. Avoid contact with eyes or prolonged contact with skin. In case of contact, flush thoroughly with water.

• Do not take internally. Silica sand may cause cancer or serious lung problems. Avoid Breathing dust. Wear a respirator in dusty areas.

• Protect finished work form traffic or damage by other trades for any extended period of time during cold weather conditions. At room temp. conditions 70 ºF (20 ºC ), protect overnight

• Keep out of reach of children.

 

Shelf life :

• Factory sealed bag of this product are guaranteed to be of first quality for one (1) year* if stored off the ground in a dry area.
• High humidity will reduce the shelf life of bagged product.

 

Other Products Categories Available : Brings the Widest range of Construction Material & Chemical.

waterproofing of concrete and sand - cement mortars used in basements, terrace, roof slabs and screeds, water tanks & water retaining structures, external plastering, internal plastering bathrooms and balconies. 200ml per 50kg bag of cement

we offer Wall Putty. BOPP Export Quality BagGerman Based TechnologyLion Wall Touch specially developed as a finish coat to cover unevenness and pinholes in plastered surface and to make the wallsceilings ready for painting

we offer Lion Tiles Grout are used for porous & absorbent type tiles, , non - vitreous clay tiles, marble and glazed wall tiles.

We offer Polypropylene (pp)Fibers (Euro Faster), is a technologically advanced polypropylene fiber specifically engineering for use in concrete, cement mortars, and ready made mixtures. It is coated with a special solution that leads to improvement of the concrete quality with respect to micro crack reduction, comprehensive strength, crack tensile strength, flexural and abrasion resistant. Used everywhere, where cements can be used

We offer block jointer. Lion jointing mortar is a masonry mortar for use in laying various types of fly ashconcrete bricks, aac block, concrete block and stones india 1st silica base mortar bopp export quality bag

We are offering ready mix plaster.It is a remixed ready to use cement based mortar for external as well as internal plaster which ensures qulity consistency India 1st silica base mortarBopp export quality bag

We offer cementitious waterproofing coating. Cementitious waterproofing coatingterrace water proofing, sloping roofs and chajjas, plastered masonry, external walls, overhead and underground water tanks, swimming pools, toilets & bathrooms, basements, tunnels, canals, dams etc. Coverage - 16 to 18 sq feet per kg for 2 coats

We are offering epoxy grout, lion l- poxy epoxy grout is intended for jointing wall and floor tiles, particularly on surface with high chemical and sets and hardners without contracting.

We are the well-known Manufacturer and Supplier of Seal & Coatings from Vijapur in Gujarat. Seal & Coating is cement based, single component polymer modified, flexible, elastomeric waterproof coating for concrete and masonry surfaces. Seal & Coating is available as a dry powder, and is to be mixed with water before use. It is grey in color and easily applied by brush or sprayed by spray machines.

Areas of Application :

• Terrace Water proofing

• Sloping Roofs and Chajjas

• Plastered masonry, External walls

• Overhead and underground water tanks

• Swimming pools

• Toilets and Bathrooms

• Basements

• Tunnels, Canals, Dams etc.

 

Features & Benefits :

• Heavy duty waterproof coating system on new and existing surfaces.

• Forms flexible and washable membrane soon after application.

• Highly effective for Positive & negative sides of hydrostatic pressure.

• Positive side Impermeability : 5-7 Bar

• Negative side Impermeability : 1.5 Bar

• Effectively seals all existing cracks in the surface

• Crack Bridging Capacity : 0.5mm. Good resistance against UV, Infrared Rays.

• Strong adhesion with all Cementitious surface including China chips.

• Non Toxic, hence suitable for all types of water retaining structures.

• Ease of handling, Mixing & application.

• Freedom from fungus/moss, improved life of finishing coats and aesthetics

 

Method Applications :

• Seal & Coating can be applied to the surface manually by brush. After application of 1^st coat, allow a gap of minimum 2 hours, before the subsequent coat and it must be applied in perpendicular direction to the first coat.

• Seal & Coating can be applied by spray machine also. For large areas use of spray machine is recommended for better speed and economy.

• Care should be taken to avoid application under direct sunlight. The appropriate application time for the product is either early morning or late evening. This is to ensure that the water which is used for mixing does not evaporate fast and the product is able to develop the design properties.

• In case of U/G tanks, O/H tanks or basement, it is quite possible that drying time may increase more than 2 hours. In such cases, ensure that first coat is dried properly before the application of the second coat.

• It is advised to use brush with soft bristle and after the application the brush should be cleaned properly.

 

Packing : 1kg bag

 

Application Mixing :

• it is very important that proper and thorough mixing of the “Seal and Coating” is done with water before use. It is advisable to use mechanical stirrer for uniform and thorough mixing and to save time and labour.

• Take a clean vessel / bucket which does not have hole or cut and add some water in the empty vessel to ensure no powder gets struck on the bottom of the vessel and put required quantity of “Seal and Coating” in it.

• Mixing Ratio - Mixing water shall be 30-35% of weight of powder.

• Mix both thoroughly to get uniform paste. Ensure that no powder is left unmixed at the bottom of the vessel. The slurry is now ready for application.

• It is desireable to use the material with in 2 hours.

• For bigger jobs, it is advisable to use mechanical stirrer and spray machines. Proper case shall be taken at the time of mixing and spraying to ensure better result.

Coverage : The Coverage of the product depends upon the surface condition, it sroughness and absorption. In normal condition, the coverage of Seal & Coating 10-12 square feet pr Kg for two coats

 

Precaution & Limitation :

• Proper slopes and outlets to drain out rain water are essential.

• Mix just enough quality that can be used within 2 hours so as to avoid wastage of the product.

• Additional water should not be added to already mixed material.

• In order to get best results, it is recommended not to use “Seal & Coating” in direct sunlight to avoid unnatural evaporation which may lead to cracks.

• Average thickness of each coating should not be more than 0.6 -0.8mm. If required, number of coats my be, increased to achieve higher thickness.

 

Shelf life :

• Factory sealed bag of this product are guaranteed to be of first quality for two (2) year* if stored off the ground in a dry area.
• *High humidity will reduce the shelf life of bagged product.

 

Other Products Categories Available : Brings the Widest range of Construction Material & Chemical.

We are offering tile adhesives.India's 1st silica base mortarbopp export quality baglion tiles adhesive is a high viscosity polymer base and self curing product. For use to tile fix on floor, wall, ceiling.White adhesive specially for white marble and italian marble

We are the reputed Manufacturer and Supplier of Super Grout from Vijapur in Gujarat. Super Grout LP 2 is supplied as a ready to use dry powder. The addition of a controlled amount of clean water produces a free flowing, non- shrink grout for gap thicknesses up to 100mm. Super Grout LP 2 is a blend of Portland cement, graded fillers and chemical additives which impact controlled expansion in the plastic state while minimizing water demand. The low water demand ensures high early strength. The graded fillers are designed to assist uniform mixing and produce a consistent grout.

 Area of Applications : Super Grout LP 2 is used for precision grouting where it is essential to with stand static and dynamic loads. Typical applications would be the grouting of base plates of turbines, compressors, boiler feed pumps, bold casting etc., it can also be used for anchoring a wide range of fixings. These include masts, anchor bolts and fence posts.

 

Features & Benefits :

• Gaseous expansion system compensates for shrinkage and settlement in the plastic state

• No metallic iron content to cause staining Pre- packed material overcomes onsite batching variations

• Develops high early strength without the use of chlorides

• High ultimate strength ensure the durability of the hardened grout

• Free flow ensures high level of contact with load bearing area

 

Method of Applications : Preparation

• Foundation surface : The substrate surface must be free from oil, grease or any loosely adherent material. If the concrete surface is defective or has laitance, it must be cut back to a sound base. Bolt holes and fixing pockets must be blown clean of any dirt or debris

• Pre – soaking : Several hours prior to placing, the concrete substrates should be saturated with fresh water should be removed with particular care being taken to blow out all bolt holes and pockets.

• Base plate : It is essential that this is clean an free oil, grease or scale. Air pressure relief holes should be provided to allow venting of any isolated high spots.

• Leveling shims : if these are to be removed after the grout has hardened, they should be treated with thin layer of grease.

• Form work : The form work should be constructed to be leak- proof. This can be achieved by using foam rubber strip or mastic sealant beneath the constructed form work and between joints. In some cases it is practical to use a sacrificial semi-dry sand and cement form work. The form work should include outlets for pre-soaking.

• Unrestrained surface area : this must be kept to a minimum. Generally the gap width between the perimeter form work and the plate edge should not exceed 150mm on the pouring side and 50mm on the opposite side. It is advisable, where practical, to have no gap at the flank sides.

 

Application Mixing and Placing

• Mixing : For best results a mechanically powered grout mixer should be used. When quantities up to 40kg are used, a heavy duty slow speed drill (400-500 rpm) fitted with a paddle is suitable. Larger quantities will require a heavy duty mixer
  • To enable the grouting operation to be carried out continuously, it is essential that sufficient mixing capacity and labour are available. The use of a grout holding tank with provision to gently agitate the grout my be required.
  • The quantity of clean water required to be added to a 40kg bag
  • The selected water content should be accurately measured into the mixer. The total content of the Super Grout LP 2 bag should be slowly added and continuous mixing should take place for 5 min. this will ensure that the grout has a smooth even consistency.

• Placing : At 300 C Place the grout with in 20 min. of mixing to gain full benefit of the expansion process.
  • Super Grout LP 2 can be placed in thicknesses up to 100 mm in a single pour when used as an under plate grout.
  • For thicker sections it is necessary to fill out Super Grout LP 2 with well graded silt free aggregate to minimize heat build up. Typically a 10mm aggregate is suitable. 50-100% aggregate weight of Super Grout LP 2 can be added.
  • Any bolt pockets must be grouted prior to grouting between the substrate and the base plate.
  • Continuous grout glow is essential. Sufficient grout must be prepared before starting. The time taken to pour a batch must be regulated to the time ot prepare the next one.

• Packing : 40kg in BOPP Export Quality Bag.

 

Precaution & Limitation :

• Super Grout LP2 is alkaline and should not come into contact with skin and eyes. Inhalation of dust during mixing should be avoided.

• Gloves, goggles and dust mask should be worn.

• If contact with skin occurs, it shall be washed with water. Splashes to eyes should be washed immediately with plenty with plenty of clean water and medical advice sought.

• Super Grout LP2 is non- flammable.

 

Shelf life :

• Factory sealed bag of this product are guaranteed to be of first quality for one (1) year* if stored off the ground in a dry area.
• High humidity will reduce the shelf life of bagged product.

 

 Other Products Categories Available : Brings the Widest range of Construction Material & Chemical.

We are the famous Manufacturer and Supplier of Integral Liquid Waterproofing Compound from Vijapur in Gujarat. The Integral Liquid Waterproofing Compound is a specially formulated waterproofing compound composed of surface active plasticizing agents, polymers & additives. It is used as an additive for cement concrete, mortar & plasters. It makes concrete cohesive and prevents segregation.

 

 Area of Applications : waterproofing of concrete and sand - cement mortars used in Basements, Tarrace, Roof slabs and screeds, water tanks & water retaining structures, External plastering, Internal Plastering Bathrooms and balconies, Sumps and drains.

 

 Feature & Benefits :

• Corrosion resistant – Makes concrete more cohesive, hence protects steel better against corrosion

• Compatibility – Being a liquid, easily dispersible & compatible with concrete / mortar mixes.

• Permeability – It reduce the permeability of water into concrete remain within the specification limits

• Strength – The setting time and compressive strength of the concrete remains within the specification limits

• Shrinkage – Reduce shrinkage crack development in plaster & concrete.

• Workability – Improves workability of freshly mixed cement concrete.

• Durability – Increases durability by improving waterproofing of concrete.

 

Method of Application :

• Charge cement & aggregates to concrete mixer as per the mix design, mix in dry state for 1 -2 minutes.

• State addition of 75 -80% mixing water & mix for 2-3 minutes.

• Double + is added as per the recommended dosage into the remaining mixing / gauging water, then add to concrete mixer & mix for another 2 min.

• Place the concrete or apply plaster, as needed.

• Cure the applied mortar or concrete as per good construction practices.

 

Precaution & Limitation :

• Do not add Double + directly to dry cement & aggregates mix.
• Maintain water – cement ration as low as possible.
• Do not increase the dosage of Double + than the recommendation.

 

Application Mixing : 200 ml per 50kg bag of cement

 

Shelf life :

• Best before Two years form the data manufacture when in sealed pack and stored under proper condition.

• Store in a cool & Dry place in unopened conditions away form direct sunlight.

 

Packing : 1Ltr, 5Ltr, 10Ltr and 20 Ltr

 

Other Products Categories Available : Brings the Widest range of Construction Material & Chemical