Welcome to Lassoart Designs
Bric International is a company engaged in business of both - indenting as well as direct exports to various countries. Over a period of time it has established itself as one of the most reliable source for industrial users of metals like steel and.. Read More
Pre-Painted GI / Aluzinc (Galume) Tile Profiled Steel Sheet -2 Overal sheet width before profile is 1120 mm (+/-10) Overal width after profile is 980 mm (+/-10) Effective covered width is 888 mm (+/-5) Pitch is 178 mm (+/-2) Depth TP1 is 27 mm (+/-2) Depth TP is 2.5 mm (+/-2) Length of step is 203 mm
For supplying quality HR products, our Principals is equipped with full fledged laboratory with test equipments, Emission spectroscope for the chemical analysis, computerized Universal testing machine with stress-strain graph for tension tests, surface finish tester, Hardness testers , LFQ testing machine, Cupping tester, on line Radiometric and off line chemical lab for corrosion resistance, and Humidity chamber. Our products are having : Excellent cold forming and deep drawing properties Excellent weldability Consistency in quality
The technology available in the complex ensures production of high quality products for critical applications in automotive, white goods, construction, etc. The wide range of products from drawable grades to high strength low alloy grades, meet the product requirements of different processes like drawability, stretch flangibility, weldability, etc. The processes are suitably backed by advanced modeling techniques for designing the products.
The products offer excellent properties such as corrosion resistance, good service life, excellent surface finish, and close dimensional tolerances. The Galvanized substrate is available in a wide range of zinc coating to provide supreme corrosion protection in various environmental conditions. Galvanized products are subjected to strict quality control tests to assure performance in all climatic conditions. Our products are having : Uniform zinc coating in the range of 90-275 GSM Spangles: Zero / regular / minimized / suppressed With and without tension leveling Passivation: Chromated (Hexavalent / Trivalent) Controlled / staggered winding
Aluzinc (Galvalume) Sheets & Coils (AS PER ASTM A792, CS TYPE B / EN-10326 / DX51D 55%AL / 43.6%ZINC & 1.3% SILICON AND OTHER ALLOYS) Production introduction : This alloy coating consists of 55% Aluminum and 43% Zinc and the balance contains majorly Silicon around 1.5% to affect excellent adhesion to the steel substrate. The metallic coating which is applied using a continuous hot-dip coating process, combines the galvanic corrosion protection of zinc with the barrier protection of aluminum. Aluzinc also displays excellent heat reflection properties, similar to aluminized steels and is more resistant to higher temperatures than hot-dip steel. It will maintain its bright appearance and reflectivity in prolonged exposures at temperatures of 320°C and is not heavily oxidized by continuous exposure to temperatures of upto 650°C. These high temperature oxidation and heat resistance attributes of ALUZINC enable the potential applications to be expanded beyond the traditional metal building market. In particular, Automotive exhaust systems, Furnace and Ovan hardware and white goods that require heat resistance (ovens, cookers, etc.) also used for Roofing and cladding, Pre-painted sheets, Air conditions, Refrigerators & Ductings etc. are potential applications of ALUZINC. Basic differenc in production of Aluzinc against Galvanize The most significant difference in process is the composition of the coating bath; the bath for 55% AlSi-Zi coated sheet production is comprised of a 55% AlSi-Zn coated alloy rather than near pure zinc for Galvanized sheets. The 55% AlSi-Zn coated bath is operated at a higher temperature (600°C 0r 1120°F) than the zinc bath used for galvanizing which is operated at about 450°C (840°F). The higher temperature for 55% AlSi-Zn coated is required because of the higher melting point of the 55% AlSi-Zn coating alloy. The melting point of the 55% AlSi-Zn coating alloy is about 580°C (1180°F) while that of the zinc coating is about 417°C (780°F) . Because of the higher bath temperature and the increased corrosiveness of the aluminum rich alloy, the 55% AlSi-Zn coated pot is lined with a special refractory and is induction fired. The general galvanizing principle of the strip heating the bath metal does not apply to 55% AlSi-Zn coated where the strip entering the bath considerably cooler than the bath (depending on base quality). Much of the bath’s heat is derived from the operation of the inductors. Prior to the strip entering the coating bath the hydrogen content of the protective atmosphere is increased for 55% AlSi-Zn coated compared to galvanized to provide maximum protection for the strip and to minimize oxidation of the bath surface. After coating in the ‘upleg’ as the strip rises in the cooling tower, air is blown onto the surface to cool the coating at a specified rate for generating the required coating microstructure for optimum corrosion resistance also fast cooling arrangement, resin coater, induction Furnace for resin coater. Product Advantage : Excellent long term durability Superior Cut Edge Galvanic Protection Superior standing water corrosion resistance Excellent Energy Efficiency Excellent Formability Excellent Paintability The coating has unique microstructure consisting of two layers, an aluminum-zinc overaly coating and an iron-containing inter-metallic or alloy layer. The alloy layer forms at the interface between the coating and the steel substrate and is very thin. The thickness of the alloy layer is minimized by the addition of silicon to the coating alloy. Varying amounts of aluminum, iron, zinc and silicon are contained in various phases of this layer. The overaly coating is composed of two main phases, an aluminum-rich dendritic phase and a zinc-rich interdendritic phase. The aluminum rich phase comprises about 80% of the coating volume, while the zinc-rich phase comprises about 19% of its volume the remaining 1% is taken up by the silicon particles. The unique microstructure combines the galvanic or sacrificial protection of zinc coatings with the barrier protection of aluminum (long tem protection into one product 55% Al-Zn coated sheet is produced in a variety of strength levels, from deep drawing to full hard. Product Specification & Size Range :
Share your thoughts with other customers for Lassoart Designs
Add Review
