Manesar, Haryana, India
Verified
Add Review
Our Products
IDE series are externally damped impulse voltage capacitive dividers and can be used to measure full and tail chopped lightning impulses as well as switching impulses at voltage levels up to 1MV. This voltage divider serves simultaneously as a load capacitor for the impulse generator. With suitable secondary arm it can also be used for AC voltage measurements.
IDI series are internally damped capacitive impulse voltage dividers and can be used to measure full and tail chopped lightning impulses as well as switching impulses up to the highest voltage levels. This voltage divider serves simultaneously as a load capacitor for the impulse generator. With suitable secondary arm it can also be used for AC voltage measurements.
RIC-500 Recurrent Impulse Generator is a low voltage equivalent of High Voltage Impulse Generator. Its wide range of applications includes the testing of models, the study of voltage distribution in high voltage windings during impulse voltage stresses and predetermination of the circuit parameters of impulse test plants. Tests can be performed quickly and reliably without endangering personnel. All impulse circuit elements and therefore, all impulse forms may be varied within broad limits. Voltage impulse may be observed and evaluated on any oscilloscope as a standing image.
The unit is especially suitable for:All impulse circuit components are adjustable. The impulse shape can thus be fine-tuned within a wide range. Additional capacitors and resistors can be connected externally to permit operation with larger impulse capacitances and other resistance values. The peak value of the impulse voltage is established and continuously adjustable. The voltage impulse may be chopped internally within broad limits.
Mobile test laboratory is to measure ratio and phase angle errors of installed instrument transformers comprising of; current transformers, potential transformers and capacitive voltage transformers. This measurement when combined with the accuracy measurement of energy meters can help in determining the actual energy transmitted. It is important to make the accuracy measurement of the complete measuring arm for determining the quantum of actual energy transmitted. It has been observed that nearly 15% of the installed instrument transformers do not meet thespecified accuracy levels thus energy metering in itself is defaulted causing huge revenue loss for theconcerned utilities.
IC-500 Impulse Calibrator monitors and calibrates impulse measuring systems by generating all key impulse waveforms according to IEC 61083-1 & IEC60-2. Entire range of measuring system can be calibrated with the wide output voltage range.
These are manufactured in the range of 50 kV to 400kV, 250 kVA to 16, 000 kVA. Tank type systems are generally used when the output voltage is less than 250kV and also when multiple taps are required to meet the different load requirements at different voltages.
The advantage of tank type system for PD Testing is that the reactor can be built with feed through bushing. This allows the reactor and its associated accessories to be placed outside the shielded room with only bushing going inside it. This reduces the size of RF shielded room and in turn its cost.
Features:
High Current Test Set is high current, lightweight, modular test sets with state of the art control circuitry and instrumentation. They provide up to 5000 Amps output with maximum burden of 15 V. These test sets can do primary injection testing of high voltage substation breakers and associated protective relays, as well as ratioing of current transformers. I Series feature Laptop controlled that measure in seconds or cycle, auxiliary contact control, and status indicators for input power, thermal overload and ground interlock.
SFC is especially designed for testing HV-devices, like MV-cables, bushings, all type of transformers and more; can replace motor-generator set. Therefore higher power is available and precise and short measurement periods are possible. A high efficient control reduces significant the normal high frequency distortions produced by fast switching semiconductors. Also available as mobile measurement system. SFC allows high power quality, precise measurement and short testing time.
The traditional method with Motor Generator Sets to test HV-devices means a lot of maintenance and installation work for the customer. Where once several MG-Sets were used, only one SFC is necessary for all IEC-standard tests.
Today testing requires more and more power what increases the cost of MG-Sets. The occurring high frequency distortion of fast switching semiconductors can be avoided by using special filter technologies.
Features:
W Seriesimpulse generators can be used to generate impulse voltages simulating lightning strokes and switching surges. The stage voltage is 100 kV / stage and the stage energy is 5 kJ. or 10 kJ. Max. Charging voltage is 1400kV.
Features:
WV seriesComputerized control system is specifically designed for the needs of HV impulse testing. The system is running a Windows based operating software package. Safety systems are properly implemented into the system as independent external emergency switches, software alarms, closed loop feedbacks and status information for fast understanding. Control system can be used in fully automatic mode, semi automatic mode and also manual mode
DH100 series HVDC Charging supplies rated for 100 kV output with different output currents for different configurations are available. This typically includes 50 kV HV AC Transformer along with voltage doubler and rectification circuit to charge the impulse capacitors through charging resistors.
The IM212 is a dual-channel precision digital impulse analyzing system (12bit) of the highest performance class with user friendly software and powerful curve analyzing tools along with report generating templates. Measurement evaluation and analysis of impulse voltages and currents can be performed according to all relevant standards i.e. IEC 61083, IEC 60060, IEC 60076, IEC 60099, and IEC 60230, for High Voltage Impulse Testing. Additional functionality tools for advanced testing are integrated. Additional analyzing software tools (Transfer function & Comparison) are available for fault analysis.
Features:
The Model#IT-21 computerized Instrument transformer test set is fully automatic and user friendly instrument for fast, accurate measurement of instrument transformer (CT/PT/CVT) errors. It is designed for use in laboratories, manufacturing processes and quality control procedures. Present increasingly severe quality control requirements call for a higher degree of operating comfort and absolute reliability of the measuring equipment employed. Based on the latest design technology this instrument sets new standards of quality, reliability, convenient operation and simple maintenance. Its measurement ranges for current/voltage errors, phase errors and current/ voltage excitation are fully up to International standard requirements
Features:
RIG-500 Recurrent Impulse Generator is a low voltage equivalent of a high voltage impulse generator. Its wide range of applications includes the testing of models, the study of voltage distribution in high voltage windings during impulse voltage stresses and the predetermination of the circuit parameters of impulse test plants. Tests can be performed quickly and reliably without endangering personnel. All impulse circuit elements and, therefore, all impulse forms may be varied within broad limits.
Q30 Precision Capacitance & Tan Delta measuring test system is designed for the measurement of very low dielectric losses and impedances (Dissipation factor and Power Factor) of high voltage equipment, liquid and solid insulation. The instrument works on the principle of a combined bridge-vector meter and is capable o analysing capacitive and inductive loads.
The graphical user interface of Q30 is highly intuitive and focussed on the convenience of operator. Advanced software functionalities such as analysis of test result, comparison of parameters and report generation makes it an advanced diagnostic instrument.
The powerful Q30 software efficiently performs test at desired voltage level and records all relevant parameters, which are user selectable. Important information related to the device under test can be feeded into Q30 for analysis and report generation.
Applications :
High Voltage Filters are used in many of the PD test systems. They allow for a PD free constant connection in the high voltage circuit and can be used as the interface between the circuit under test and the PD detectors. Conducted interfering signals caused by the power supply are often damped only insufficiently by using a single-stage filter. The damping of these interfering signals can be improved if single-stage filters are enlarged by an additional stage to two-stage filters.
TO Series oil insulated cable test terminations are used for AC testing as well as for partial discharge and tan delta measurement. Their main characteristic include easy handling, short cable preparation times and very short setup times, this is of great importance in routine test application .
The cable end can be away prepared from the test laboratory and the cables can be easily installed in the termination. KVTEK offers test termination up a rated voltage of 150 KV.
D22 has built-in Calibration that allows calibration to be performed automatically. It injects a known PD signal from 1 pC to 1000pC into a PD test circuit to allow verification of calibration.
Software of D22 allows to generate the report by adding the company logo, customer and test object details. All measurement results, PD pattern, graphs and test object data can be saved on the hard disk or printed directly.
Partial Discharge testing is a sensitive mean of assessing the quality or condition of insulation contained within the high voltage equipment. It can be caused by poor design, manufacturing faults, mechanical damage or aging. D22 based on straight discharge detection principle, is versatile high performance digital detector designed to make highly sensitive measurements on all types of high voltage insulation systems. The ability to measure low levels of partial discharge is referred to as sensitivity. Different products have different inherent acceptable levels of partial discharge ranging from 2pC to over 1000pC.
D22 has built-in Calibration that allows calibration to be performed automatically. It injects a known PD signal from 1 pC to 1000pC into a PD test circuit to allow verification of calibration. Software of D22 allows to generate the report by adding the company logo, customer and test object details. All measurement results, PD pattern, graphs and test object data can be saved on the hard disk or printed directly.
Applications:
Partial Discharge testing is a sensitive mean of assessing the quality or condition of insulation contained within the high voltage equipment. It can be caused by poor design, poor processing techniques, polluted environment on shop floor, manufacturing faults, mechanical damage or aging. D216 based on straight discharge detection principle is a versatile high performance digital detector designed to make highly sensitive measurements on all types of high voltage insulation systems. The ability to measure lowest possible levels of partial discharge is termed as sensitivity of the PD Detector. Different products have different inherent acceptable levels of partial discharge ranging from 2pC to over 1000pC.
Multiple, independent channels mean inherent redundancy in case of a failure of a plug-in channel. The channels can be used in multiple configurations together.
IEC and IEEE/ANSI compatible PD Testing: The system hardware can be set to make measurements as per the frequency filter settings laid out in the latest versions of either the IEC or the IEEE/ANSI standards.
Pattern Acquisition and Display: The system allows true parallel acquisition of the partial discharge activity on all the multiple channels with simultaneously display.
D216 has built-in calibrator that allows calibration to be performed automatically. It injects a known PD signal from 1 pC to 1000pC into a PD test circuit to allow verification of calibration.
Software of D216 allows to generate the report by adding the company logo, customer and test object details. All measuring results, PD patterns, graphs and test object data can be saved on th hard disk or printed directly.
Applications:
These shunts are used for the measurement of impulse currents in high-voltage test labs. The measured wave shape of the current can be displayed on a KVTEK's impulse analyzing system IM212 / IM412.
IC-500 Impulse calibrator monitor and calibrate impulse measuring systems by generating all key impulse waveform according to IEC 1083-1 & IEC60-2.
All range of measuring system cab be calibrate with the wide output voltage range.
Generator, transmission and distribution transformers are some of the most critical and expensive assets in a power network. Moisture is a necessity in cellulose materials, but too much is absolutely detrimental to the service life of power transformers. Moisture, more specifically excessive moisture, has been enemy number one in power transformers utilizing cellulose insulation with insulating oil for a long time.
KVTEK developed a system (MAS10) that would remove moisture continuously in a gentle manner. A unique molecular sieve technique is applied to continuously remove moisture and particles from the transformer oil.
MAS10 system has the capacity to remove approx. 10 liters of water from a transformer before saturation, but the rate at which it will absorb water will depend on many factors, mainly, how much water is available in the oil, and the temperature range through which the transformer will operate. The design flow rate of the pumped oil is nominally 90 litres per hour to give maximum absorption through the molecular sieves.
| Model | No. of Cylinder | Suggested Transformer Size | Water Removal Capacity |
| MAS3 | 1 | Less than 10 MVA | 3 Litres |
| MAS10 | 3 | 10 MVA and Above | 10 Litres |
| MAS30 | 3 | 50 MVA and Above | 30 Litres |
MCG series multiple chopping gap is used to chop lightning impulses on the front and/or on the tail. It also serves simultaneously as a load capacitor for the impulse generator and allows excellent reproducibility of the chopping time and does not distort the wave shape until the chopping point. The sphere distance is automatically adjusted and operated by the WV 23 Impulse controls.
These modular systems are built for voltages generally ranging between 200 kV to 1600kV, power ranging between 250 kVA to 64, 000 kVA. Higher voltages are achieved by having multiple modules stacked in series on top of one another.
It is not possible to have multiple taps on the modular system but different tuning ranges are achieved by connecting the modules in series or parallel.
Features:
