kssr enterprises

Porur, Chennai, Tamil Nadu

Power frame

Power frame is totally enclosed. Dust and oil tight enclosure elimination contamination from the outside elements.

Reduced maintenance cost and increased reliability.

Connecting Rods

Accurately machined and honed for longer life I-section design for rigidity and light weight. Split-bolted marine type crank-pin end for easy assembly and disassembly. Refle-drilled oil passage.

Cross Head

Fully cylindrical crossheads and guides ultilize maximum possible bearing area. Less weat thru greater disbursement of bearing loads. Assures greater reliability with low replacement costs.

Crank Shaft

Forged hardened and ground crank shaft provides unmatched strength and surface hardness for long life.

Lubrication

Splash type lubrication system for all power and bearing contained within sealed chamber.

Bearning

Antifriction steel-tapered roller bearing provides extended bearing life.

Lubrication

Splash type lubrication system for all power and bearing contained within sealed chamber.

Plunger

The triplex plunger pump performs smoothly and quietly. The natural lubricity of the pumped fluid cools and lubricity the seals. The hardened, polished ceramic coated plunger provide extremely durable wear surfaces, abrasion resistance and maximum seal life.

Gland plucking

The stuffing box assemblies are individually bolted to the fluid cylinder for easy accessibility, for disassembly and assembly. Reduced maintenance costs and downtime.

Valve Assembly

All Valve assemblies are completely independent of and are clamped between manifolds and fluid cylinder. Easy valve inspection and replacement without any clean-up or rematching of mating components.

Plunger pumps are positive displacement pumps that" displace" a given amount of fluid on each cycle stroke of operation .The reciprocating motion of a plunger, with a ball check valves on each side of the pump body, creates the pumping action. Pumps can be offered in simplex, duplex or multiple heads for handling different chemicals with common motor. Each head has independent connection and the capacity of head can also be independently adjustable. They can be single acting or double acting. Plunger Pumps are reciprocating positive displacement pumps which are generally configured in four ways: direct-acting or indirect-acting; simplex or duplex; single-acting or double-acting; and power pumps. A simplex plunger pump, sometimes referred to as a single piston plunger pump, is a pump having a single liquid ( pump ) cylinder.

A Parker pressure-loaded gear pump consists of two, intermeshing, hardened-steel, precision-ground gear, assemblies. These precision gears are enclosed by a high-strength, die-cast aluminum front cover, back cover and a high-yield, strength-extruded aluminum center section.

Gear assemblies consist of one drive gear, shrinkfitted on a precision-ground and polished drive shaft. This shaft extends outside the pump to permit coupling to an external prime mover. The second gear, being the driven gear, is also shrink-fitted on a precision-ground and polished driven shaft. Retaining rings, which are installed in grooves provided on the shaft, ensure that the gears will not move axially, and a key keeps the drive gear from moving radially.

A lip-type, shaft seal is provided at the drive shaft to prevent external leakage of pump fluid. The sealing lip in contact with the fluid is spring-loaded. Vent passages within the housings and driven shaft communicate pump inlet pressure to the rotary seal area, thus imposing the lowest possible pressure at the rotary seal for extended seal life.

Pump rotation is dependent upon the proper orientation of the heat shield, backup gasket, and rubber seal in the front cover housing, the center section and rear cover, respectively. Pumping action is achieved by connecting the pump drive shaft to a prime mover, and rotating the gears away from the inlet port. Rotation causes the gear mesh to increase on the inlet side and decrease on the outlet (pressure) side.

A Parker pressure-loaded gear pump consists of two, intermeshing, hardened-steel, precision-ground gear, assemblies. These precision gears are enclosed by a high-strength, die-cast aluminum front cover, back cover and a high-yield, strength-extruded aluminum center section.Gear assemblies consist of one drive gear, shrinkfitted on a precision-ground and polished drive shaft. This shaft extends outside the pump to permit coupling to an external prime mover. The second gear, being the driven gear, is also shrink-fitted on a precision-ground and polished driven shaft. Retaining rings, which are installed in grooves provided on the shaft, ensure that the gears will not move axially, and a key keeps the drive gear from moving radially.