KSP POWER CONTROLS Kolkata, West Bengal

Servo Voltage Stabilizer We supply a gamut of Buck-Boost Transformer that is widely used in Servo Stabilizers and can be customized as per the specific requirements of our clients. These boost transformers are made in compliance of necessary standards. Some of boost transformers features are: Highly durable • Saves energy cost • Cost effective

Servo Voltage Stabilizer is commonly observed that, AC main supply is never 230 Volt or 415 Volt, but varies from 150 Volt - 300 volt and 300 Volt - 500 Volt. The difficulties caused by them are well known, such as Over Load Condition, Line Losses, Poor Power Factor and several other reasons. Generally constant voltage which is required to load is never constant, but in fluctuation manner. It is observed that during the daytime, the voltage is quiet low and during the night the Voltage is high then the normal. This fluctuation in supply system results frequent breakdown, low production and also loss of energy. The performance of any electrical equipment is optimum at its rated voltage. Both over / under voltages are harmful for the system. The under voltage reduces efficiency whereas the over voltage shortens the life. The power agencies insist the consumer to fix the capacitor to improve power factor to get better results in power saving. But Voltage is far more important factor to save the power loss. In case of very Low / High voltages, the telecom systems are powered by DG sets. Our Line Conditioner Unit meets the requirement of input voltage variation from 110V - 280V (Single phase) and 300V - 500V (Three phase). 240V - 500V is also available on demand. In India, there are large voltage variations in the mains power supply. To overcome this problem, we are offering Line Conditioner Unit. General Servo Stabilizers are automatic line Voltage corrector using synchronous motor in close loop control. The stabilizer employ continuously variable auto transformer, buck-boost transformer, AC synchronous motor, state of the art IC closed loop control system with all protection, metering, indication and control system to give desired output voltage within the specified limits for a range of input voltages. Provision for manual correction of voltage can also be provided.

Transformers also provide an extremely useful feature called isolation, which is the ability to couple one circuit to another without the use of direct wire connections. There are applications where electrical isolation is needed between two AC circuits without any transformation of voltage or current levels. In these instances, transformers called isolation transformers having 1:1 transformation ratios are used. Our Isolation Transformers isolate the equipments from noisy power line hence providing a better option to clients. These remove power line noise, surges, spikes and transients. It also provides high insulation resistance and provides complete electromagnetic and electrostatic shielding. Our range of Isolation Transformers is designed as per the international standards which give an assurance to the customer on the high quality of the product. An isolation transformer does not have a direct electrical path from the power input side to the power output side. The term is also used to define how much electrical isolation exists between the input and output windings. For example when using line-voltage input transformers to power low voltage device handled by humans, a high degree of isolation is required for safety. Isolated transformers often use separate bobbins for the primary and secondary coil windings, but usually the windings are just wound on top of each other with insulation in between. There is usually an electrostatic shield between windings which is tied to transformer case.

• Weight500 Kg
• Power18.5 KW

We offer high quality Step Down Transformers. It is hard wired, durable with a heavy duty chord. It has a 100 Watt maximum capacity and can be used continuously over a period of time. It has one grounded outlet in front of unit (accepts 3 or 2 prong US and Euro plugs) and reduces the voltage to the fit the next level of desired use. Perhaps it will go to some point in a factory, shop, home or even the much smaller applications and be reduced again to fit a lower voltage piece of equipment. Step Down Transformers have a primary winding of higher number of turns than the secondary winding. Since power is fixed, lowered voltage results in increased amperage; the lowering of voltage is inversely proportional and results in increase of amperage. Our Step Down Transformers are relatively simple in design and they have the exact ratio of windings in each circuit so as to deliver the appropriate current and voltage. Application, budget and other factors must be considered before installing a particular transformer. Both incoming and outgoing voltages must be known prior to selecting any Step Down Transformer. We offer all our products as per ISI specifications which give an assurance to the customer on the quality of our product. We are equipped with an R&D unit and testing tools and section which has got all tools and testing facilities that support us in supplying products as per client’s specific requirement. Features: 1KVA to 300KVA maximum capacity heavy-duty continuous use transformer One grounded outlet in front of unit (accepts 3 or 2 prong US and Euro plugs) Hard wired Durable design with a heavy-duty cord

Industrial Battery Chargers – KSP Power Controls has been a valued supplier to couple of customers for their customized requirement on Industrial Battery Chargers in India. These Industrial Battery Chargers are being used along with couple of Equipments which require DC voltage to run them and once Batteries get discharged the same needs to be brought back to station for Charging and restage. It has been designed CVCC (Constant Voltage Constant Current Chargers ) for such applications wherein customer can use Sealed Batteries Also and enjoy the luxury of using product with best of the life from Batteries. KSP Power Controls Battery chargers can also be used for UPS applications where in majorly all Multinational UPS manufacturers Have 4 amps chargers for sizing up to 10KVA UPS systems. Customers who look for larger backups need additional Charger to charge batteries which becomes a big issue for End customers. We have ensured that customers can feel Comfortable technically by adding additional charger along with their UPS and procure batteries of higher capacities too now. Technical features: Input: 240 V, 1 phase or 415 V, 3 phase, 50 Hz AC CVCC Charger Available in 12V 5Amps to 20 Amps Available in 24V 5 Amps to 20 amps Available in 36V 5Amps to 20 Amps. For E Rickshaw Available in 48V 5Amps to 20 Amps. For E Rickshaw Available in 24V to 408 V from 5Amps to 20 Amps. For UPS systems Air Cooled Construction Suitable for indoor / outdoor applications Fully tropicalised Liberally designed components and adequately dreaded diodes.