Krutam Technosolutions Pvt. Ltd.

Makarpura, Vadodara, Gujarat

This DIN Rail mounting instrument is highly useful far controlling over current in any process industries. With use of C.T. any current range is feasible for controlling. Instrument works ok with under current limit and trips if current exceeds the set limit.

Application

• OEM Equipment in control panel of process industries.
• Works as over current limiter.
• Economical priced for panel instrument.

This machine is light, compact and simple design used to test the fatigue strength of materials and draw S-N diagram used for research institutes, laboratories, material manufacturers and various industries.Table model, no need of foundation.This is a rotating beam type machine in which load is applied in reversed bending fashion.The standard 8 mm dia specimen is held in special holders at its ends and loaded such that it experiences a uniform bending moment. The specimen is rotated at 4200 rpm by a motor. A complete cycle of reversed stresses in all fibres of the specimen is produced during each revolution.The bending moment is applied with a lever system and can be easily changed by moving a weight over the lever.

Electronic Extensometers ( Model : FEE-5 )

• This instrument is to be used on Tensile or Universal testing machines to find out Proof stress & Young's modulus values.
• In case of many brittle materials such as high carbon steels, alloy steels, light aluminium & magnesium alloys, it is difficult to get yield values. For such materials stress corresponding to a certain allowable amount of plastic deformation is termed as proof stress say 0.1% or 0.2% proof stress.
• The measuring range is upto 5mm & resolution is 0.001mm.
• Standard two fixed gauge lengths of 25 & 50 mm is provided. Different sizes gauge lengths can also be given at an additional cost.
• If this extensometer is ordered with a computerized UTM, then a special menu driven application software is provided, which accepts load & extension values, & evaluates proof stress values.

• Machines are designed to test chains, wire ropes & any long specimens for proof test or destructive tensile test.
• High loading accuracy & infinitely variable straining speeds to suit a wide range of materials.
• Continuous roll autographic recorder to get load - elongation graph.
• Robust loading frame, Simple controls & easy to operate.
• Adequate safety devices for safe operation.
• Analogue models with large dial & load measurement by pendulum dynamometer principle.
• Digital / Computerized models are also available where load Vs elongation is in digital display & printout of results can be taken.
• Special Accessories like - Extra Bed length, Extra Ram stroke, Various special grips / attachments / fixtures as per sizes / shapes of specimens, Load-stabilizer (at extra cost) can be provided to suit special application.
• Various Models - Maximum Capacity from 100 kN to 3000 kN.
• Loading accuracy well within 1%, conforms to IS:1828 / BS:1610.

The machine is used to test wide range of Leaf Laminated Springs for load rate as per IS:1135-1984.Measuring ranges available with auto load selection facility.Large size table for wide range of springs with motorized rapid adjustment of test height.Standard autographic recorder.Over load & Over travel safety provisions.Facility of Compression, Shear, Brinell & Bending test with extra accessories.Load stabilizer (Optional) is an extra attachment used to maintain a desired load constant at specific deflection enabling measuring it easily & accurately.

This is specially designed to conductcompression and crushing strength tests onContainers, Concrete cubes & cylinders, hollow blocksand various other materials. Suitable for conduct inCold Crushing Strength test on refractory specimens, these testing machines is thoroughly examined by ourvendors on predetermined parameters before dispatchto our clients. Our machine is moulded byour reputed and certified vendors using the finestquality raw material and modern machines. This isappreciated for its diverse features like utmostdurability, low maintenance and a longer service life.

Model: Px-20Features

• Digital versatility with analog touch
• PC compatible through Recorder / printer (optional)
• 99 calibration sets memory
• Low frequency performance enhancement (Optional)

Model: EF-1Y & EF-2Y

Features

• Articulating & double jointed legs for good contact
• Light weight, strong & rugged.
• Complies various International Standard

Features

• 8 individually programmable channels
• 9 sets of Memory
• Recorder output available

The Notch Cutter is used for cutting the Notch in sample before conducting izod & charpy impact tests on Impactometer. The machine consists of a graduated scale which enables accurate control of the depth of the notch cut by HSS cutting blade. The machine parts are of sturdy construction duly hardened and blackened.

Microscope Type ESM1T, VMM4, VMM6 & INBT2 can be Interfaced to your own computer to give instant photographs of the Microstructure image. This attachment enables you to take sharp & clear Microstructure photographs & & their printouts instantly. The Image can be viewed on computer monitor. The image can be saved on computer hard disk & you can maintain a permanent record of your inspected samples .The saved photographs can be sent to your vendors or clients by Email.In absence of the computer it can be seen on TV This attachment is very much necessary If Image analyzer software is to be used

• Regulated power supply for the CCD Camera , camera to computer cord
• Camera to Microscope Opto-Mechanical coupler.
• Frame grabber card ( to be fitted inside your Computer on the PCI slot) with its Installation manual and Original CD of the Capture program software.

• The machine is table mounted, digital & hand operated.
• Load measurement by load cell & displacement by rotary encoder. LCD display on DAS panel for Load & Displacement.
• Standard load resolution is with 10, 000 counts. Finer resolution (Optional) with 20, 000 counts can also be offered at extra cost. Standard displacement resolution is 0.01 mm.
• Vertical day light is 300 mm.
• Tension Shackles & Compression plates are provided for Tension & Compression springs.
• It is possible to use a number of load cells, say two or three, to cover much wider range of load, to suit the application. Cost of one load cell is included in the price, but additional load cell will be at extra cost.
• Various Models - Maximum Capacity from 100 N to 2000 N.
• Loading accuracy well within 1%, conforms to IS:1828 / BS:1610.

This machine is designed for measuring hardness of metals & alloys of all kinds, hard or soft, whether round, flat or irregular in shapes.Semi-automatic, motorized, digital, microprocessor based panel. We can get hardness in digital version.Centronics parallel port for connecting dot matrix printer.Three modes of operation viz. Motorized automatic mode, Motorized mode & Manual mode.Automatic weight selection by thumb wheel.Test height x Throat is - 295 x 148 mm.Machines strictly conforms to IS:1586 2281, BS: 240, ASTM-E-10

Digital Rockwell Hardness Testing Machines ( Model : TRS-DM, TSM-DM, TRB-DM, TRB-250-DM, TRS-DM-P )

• This machine is designed for measuring hardness of metals & alloys of all kinds, hard or soft, whether round, flat or irregular in shapes.
• Semi-automatic, motorized, digital, microprocessor based panel. We can get hardness in digital version.
• Centronics parallel port for connecting dot matrix printer.
• Three modes of operation viz. Motorized automatic mode, Motorized mode & Manual mode.
• Automatic weight selection by thumb wheel.
• Test height x Throat is - 295 x 148 mm.
• Machines strictly conforms to IS:1586 / 2281, BS: 240, ASTM-E-10

In the wake of technological advancement and automation, existing mechanical dial type Universal Testing Machines are getting obsolete. Moreover it takes plenty of time for testing. Plotting of graph of required test in different units is still more difficult. Evaluation of important parameters like Proof stress, Young's modulus is very tedious and time consuming.

For mounting the specimens with Bakelite powder Specimen is kept face down in the Cavity & bakelite Powder is Hot moulded around itc with hydraulicpressure. Mould dia 30 mm.

With Digital timer. Operates on 220 V A/C

Model: PY-1

Features

• Lifting Capacity: 18 kg. At 100 mm pole spacing
• Capable of Testing with both Dry and Wet method

Both polish papers or polishing Cloth can be clamped on the rotating disc. Provision for waterflow & control.No of Disc - One Disc diameter 20 cms.

Model: DS-322 / 311Features

• Colour TFT display with choice of trace colour.
• Multi DAC curves
• Active Freeze
• Memory of 200 A-Scan
• In-built DGS software

For preliminary surface preparation of metallurgical specimens in the laboratory it is an effective machine.Belt tension is adjustable.Belt can be quickly changed.Adequate safety provided by the belt guard.

Model: M-4000 & M-6000

Features

• Suitable for AC & HWDC (4000 / 6000 Amp)
• Heavy-duty castor wheels for carrying in shop floor
• Remote control option for convenience & productivity

The excellent frequency response the signal amplifiers and the stable triggering abilities from only 5mm peak-to-peak on the screen, enable the scope to display sine waves far beyond Its -3db frequency without any problems. With rectangular signals the instrument's own overshoot is less than 1%.

Both scopes contain a second trigger system to ensure stable triggering of asynchronous signal components.

Low noise 8 bit flash converters are used to digitize the signals to be analyzed. With memory of 1 Mpt per channel , it gives indepth details for storage and analysis.

The well-proven CRT is suitable to reproduce signals with this high horizontal resolution.

2 GS/s allows a clear display of single shot (real time) events. 20 GS/s random sampling is used for repetitive signals. To display variations of a signal over several samples It is recommended to use the envelope or the average mode.

Another Important feature is the pre/post trigger function that enables the user to analyze signal components that occur before / after the trigger event. Nie full-size reference memories with 2k points, allow the comparison of signals with those already stored In memory.

When the Autoset function is enabled, all relevant parameter settings are performed by the scope's circuitry automatically. The Setup parameters and the measured values are clearly displayed on the screen in alphanumeric characters. Autoset also initiates automatic cursor settings for time and frequency measurement (digital only) as well as voltage measurement.

In analog and digital mode, the cursor functions enable the user to analyze a signal while watching the numeric readout for voltage difference, time difference, or frequency values. Another feature is the storage capability for nine complete parameter set ups, which may be stored and recalled simply by pressing the appropriate front panel key.

It has a built in calibrator - a 1kHz/1MHz square wave generator. It allows frequent checking of the Instrument's frequency response-from the probe tip to the display on the screen. It also permits high frequency alignment of the probes. Supported by an On Screen Menus adjustments can be performed without opening the scope.

With all of the new HAMEG scope range, microprocessors manage the front panel inputs, calculations and other control Functions. In addition, 32bit HISC processors accelerate the digital signal processing.

The Instrument may be remotely controlled by any personal computer via its built in serial interface in all relevant functions. A suitable software program is supplied with the scope on delivery.

Features :

Analog

• 2 x DC to 2000MHz, 2 x 1mV-50V/div
• Timebase 0.5s/div to 20ns/div
• Timebase with delay and 2ndTrig.
• Triggering DC to 250MHz, TV Sync. Separator
• 1kHz/1MHz Calibrator, CRT with 14kV

Digital

• 2 GS/s Real Time Sampling, 20 GS/s Random Sampling
• 2 Mpt memory per channel , Memory Zoom up to 100, 000:1
• Frequency Spectrum display with FFT
• 2 Channel 1mV - 5 V/cm, TB 2ns - 50s/cm, 4 logic channels(option)
• Pre/Post Trigger -100% to +400%
• Math Operations
• Auto measurements
• Cursor measurements
• USB STick and USB/RS232 interface, optional: IEEE488, Ehernet interface

This is an ideal, small & compact machine for cutting specimens for microscopic examination.Its unique Job clamping vice slides against the cutting wheel by a counter weight.Coolent pump is in built.

ype RV5 is a specially designed system for visual video inspection of inside surfaces of Pipes. it consists of an integrated insertion unit with high resolution CCD Camera which provided high resolution real time images of the pipe surfaces & is very useful for viewing the areas where L L bend or T Joints are welded to the pipe. LED array attached to the insertion unit illuminates the area under inspection . The real time images can be observed on the inbuilt LCD TFT Monitor or a laptop computer with a USB Port.

he CCD camera can be interfaced with the computer for image capture & processing with user friendly Software. Visual inspection can easily detect any defects such as removal of chromium plating, pitting, erosion , corrosion , Cracks & also welding surface defects . The latest trend in quality management programs require record of inspection to be made & retained for future reference . By Introducing video inspection the data can be substantiated as traceable records are easily available.

The high power LED array fitted on the front of the camera provides adequate illumination which can be controlled independently. The LED arrays last for a long time & consume minimum power in absence of normal 220V A/C power supply RV4 System also works on a vehicle battery of 12V RV5 system is very rugged & capable to operate in field conditions with high temperatures humidity, dusty & unclean atmosphere, is easy to operate & also completely portable.

Starting from 1GHz up to 26.5GHz, Tracking generator and various measurement facilities. LISNs, EMI software, EMI analyzers, RF Probes, Antennas.

• Spectrum Analyzer
• HM5510 1 GHz Spectrum Analyzer
• HM5014-2 1 GHz Spectrum Analyzer with tracking generator
• HM5530 3 GHz Sprectrum Analyzer
• EMI/EMC Solution
• EMCIS EMI Analyzer EA-2100
• EMCIS Filer Analyzer FA-2000
• EMCIS Filer Analyzer FA-2100
• EMCIS EMI Spectrum Analyzer ESA-2000
• Hameg Line Impedance Stabilization Network HM 6050-2
• EMCIS Line Impedance Stabilization Network LN2-16
• EMCIS Line Impedance Stabilization Network LN-20
• EMCIS Line Impedance Stabilization Network LN4-50/100
• EMCIS Power Line Filter LF1-16A
• EMCIS Shielded Chamber
• HZ 530 EMV Near Field Probe set upto 1 GHz
• EMCIS DC Bias Source

The SM5051 is a high performance Universal Counter. The instrument has three high sensitive inputs and provides signal measurement capability from 01 Hz to 1 GHz. Period measurement can be done from 1 us to 100s. With a very high timing resolution, precise measurements can be performed in the period averaging mode. This enables reliable measurements in fast logic circuitry.

SM5051 has been designed to deliver optimum performance at low cost with high reliability in diverse applications such as frequency monitoring, production testing , research and development and education amongst others.

Features

• Frequency Range 0.1 Hz to 1 GHz
• Sensitivity 20mV max.
• Period Measurement & Event Counting
• Automatic Positioning of Decimal Point
• Leading Zero Suppression

The various signals available from the SM5071 Function Generator make it a versatile signal source useful for most measurement and test applications. Special features are the high signal purity and constant amplitude flatness throughout the entire frequency range. This makes the instrument ideal for a broad range of test bench use including precise audio measurement.

It generates 3 basic wave forms: sine, square and triangle. The output frequency can be swept internally and externally over a 100:1 ratio.

This is especially convenient for examining transmission curves of a circuit under test using an oscilloscope as an indicator. The square wave output has a fast rise and fall time of

The SM5035 Pulse Generator is most suited for analog digital and logic applications in versatile environments. Pulses of varying frequencies and duration are available from its normal or complementary data outputs. A built-in-error LED indicates when pulse width is greater than pulse period. Output amplitudes are variable upto 10V (open circuit).

The impressive performance, ease of operation and low cost make SM5035 a favorite for a large variety of analog and digital applications such as testing, logic interfacing, differential input amplifiers and multiplexer, wide band amplifiers, or simulation of line drivers, opposite phase clocks and switching cycles.

Features

• Wide Frequency Range: 2Hz - 20MHz
• Pulse duration 20ns to 200ms
• Fast rise/fall time of 3ns
• Complementary Dual Outputs 5V & 2V
• Enternal, External & Manual Triggering

Model: Bl-100 & Bl-100f

Features

• Bulb with Koop glass filter for eye protection
• Built-in silent fan for cooling

Model: EF-1000, EF-1500, EF-1500-2 & EF-2000

Features

• Heavy duty cycle 2 min. ON & 2 min. OFF
• Available in 1000, 1500, 2000 Amps.
• Suitable for surface & subsurface defects.

Features

• Frequency Range 10 mHz to 12.5 MHz
• Output voltage 20 Vpp
• Rise and fall time < 10 nS
• Pulse width adjustment
• Arbitrary waveform generator 40 MSa/s
• Burst, gating, external triggering, sweep
• RS232 Interface, Optional : USB , IEEE488

A favourite with watchmakers and jewellers. Using precision acrylic lens the unit is very light ( 7 gms) and can be held comfortably in the eye socket. Also available with adaptor for use with spectacles.
Magnification: 4 X

This magnifier is mounted on a comfortable head band. Since both eyes are used it provides 3D vision enabling fine manual coordination. Ideal for any kind of detail work where both hands are required to be free to attend the work. , Available in five models with different magnifications 1.5 X, 1.75 X, 2.0 X, 2.75 X and3.50 X.

Digital, hand operated, coil spring testing machines ( model : stm )

• the machine is a free standing unit built sturdily.
• the broach is mounted in a carrier, which is drawn by a twin lead screwmechanism through the full stroke with the help of 0.5 hp motor.
• v/u notch broaching machine fixture to clamp the specimen. The tooling includes the vice for holding the 10mm x 10mm specimen. The tooling / fixtures include the adjustors & the end stop necessary to ensure the notch depth & position accurately as per the standards.
• the approx. Weight is around 100 kg.
• the machine dimension (approx.) 385mm x 385mm x 1050mm.

the machine will broach a notch in 10 mm square material to the following standards.

• a.s.t.m.a 370, e23
• din 50 115
• b.s. 131 : part i, ii, iii, iv
• bs en 10045 - 1993
• is 1598 1977, is 1757 1988, is 1499 1977

Order -NABL accreditated certificate traceable to National Standards."

Features

• Voltage measurement - 1000V AC/DC, Current
• With Resistance & Capacitance measurement functions
• Data hold, Continuty & Diode test with beeper functions

Order -NABL accreditated certificate traceable to National Standards."

Features :

• 4 4/5 Digits, 50, 000 Count display
• Large LCD display with Back light
• New style bar graph display based on binary bit expression
• Peak detection mode
• Easy determination on with GO/No-Go mode
• 5 MHz frequency counter
• True RMS for AC or AC + DC mode
• Dual Display for frequency
• AC voltage & dB measurements
• 10 Location Memory
• MIN, MAX, AVG and relative mode
• Capacitance and conductance measurements
• Temperature mode.
• Continuity and diode test
• Logic test
• Auto Power off and "keep on" mode
• Fused 20 A input with warning beeper
• Data hold and run mode
• Low Battery indication mode
• Overload protection

Model: B-5000 & B-6000

Features

• Available in 2000 to 10000 Amp.
• Rugged construction for reliable inspection.
• In-built power source
• AC / HWDC changeover by Selector Switch