Tielo Industries

Kondhwa, Pune, Maharashtra

TIELOVertifix Tile Adhesive is a rapid setting, rapid hardening, polymer-modified, pre-blended, cement based mortar bed and sloping mortar for leveling and ramping up to 3" on horizontal substrates; up to 5" thick in confined areas such as trenches. May be also used for walls and countertops, TIELOVertifix Tile Adhesive sets to a walkable hardness within one to two hours for installation of ceramic tile & natural stone tile flooring.Formulated for dimensional stability and exceptional bond strength, TIELOVertifix Tile Adhesive is ideal for pre-sloping under waterproofing membranes and mortar beds in shower applications, for countertops and patching

TIELO Universal Tile Adhesive is a single component, cementations polymer based tile adhesive material in powder form composed of cement, selected grades of silica sand and special chemical additive, which only needs on site addition of water to make a mortar which is used for fixing tile over any cementation surface. TIELO Tile Adhesive has good bonding and consistency in different climate, and can be used for adhering different kind of tiles, only requires addition of water. 

Properties :

TIELO Universal Tile Adhesive provide the following properties.

• Factory mixed – consistent quality
• Better workability, save up to 25 – 50% of time.
• Better coverage: 8-9 m per 20 kg (based on 2 mm mortar thickness)
• Tiles can be adjusted up to 30 minutes after application
• Fixing wide range of tiles
• Good bond adhesion

Primary Uses :

TIELO Universal Tile Adhesive mainly use for fixing tile in the following substrates

• Concrete
• Hard natural and reconstituted stone
• Solid rock
• Hollow and solid masonry
• Cementitious plaster and render

Advantage :

• Easy to use, only water to be added
• Excellent water proofing characteristics.
• Self-curing.
• Long working time.
• Good mechanical strength.
• Usable on a wide range of surfaces

Characteristics :

• Extended open time up to 30 min at 20 dc.
• Pot life up to 2h30min at 20dc
• Initial setting time is up to 360min
• Final setting time starting 420min
• Excellent adhesion to the substrate
• Economical by 10-20% than conventional mortar

Application : All surfaces should be sound, clean and free from any contamination like grease, oil, loose particles etc. before application, the surface and tiles should be pre wetted properly. TIELO Tile Adhesive is to be mixed with water in the ratio of 1: 0.2 to 0.25 parts by weight and stir till a smooth paste is obtained. Allow the paste to stand for 4 to 5 minutes and stir again. Spread the paste on the surface to a uniform thickness of 3 to 4 mm. With a notched trowel to remove any trapped air, place the tiles firmly into position by twisting action. Excess adhesive is to be removed by using damp cloth. Powder should be added to water and not vice versa

Coverage : 8-9 Sq. mtr. per 20 Kg Bag for 2mm mortar thickness. Coverage may vary depending on the trowel notch size, type and size of the tile and the nature of the substrate

Mixing : Mix 1 Kg of TIELO Tile Adhesive with water ranging from 200-250 ml to get a trowel able consistency for fixing tiles. Water can be reduced or increased slightly to achieve desired consistency.

TIELO Universal Gold Tile Adhesive is a cementations material in powder form composed of cement, send and special chemical additive, which only needs on site addition of water to make a mortar. TIELO Universal Gold Tile adhesive also apply the new flooring over existing flooring. Just ensure that existing flooring is good condition, clean and level so that you can use tile on tile technique and reduce time and money. TIELO Universal Gold Tile Adhesive is also used for fixing tiles on difficult surface also. It is especially recommended for hygiene sensitive areas and also areas which require sterile conditions. 

Primary Uses:

TIELO Universal Tile Adhesive is mainly used for

• Fixing Glazed
• Ceramic
• Terracotta Tiles
• Vitreous Tiles
• Marble and Granite Tile on a cementations surface
• On existing mosaic or ceramic floor tiles without removing them or hacking them.
• Used for tiling on difficult vertical cementation surfaces
• The weight of the tile is more than the normal ones.
• For plaster crack repairs
• Paver joint grouting

Advantages :

• Can be used for fixing tile over tile
• No need to break or hack the existing tiles
• No wetting of tiles required before fixing
• No wetting of surface to be tiled
• Make the tile area waterproof
• Holds the tile even at high temperatures
• Single component hence easy to send

TIELO New Construction White (NCA) is ready mix white cement based thin-set adhesive for fixing of Tile/Marble Adhesive, manufactured from white cement, fine graded sand/quartz sand, polymer and special additives, having an innovative property which prevents emitting low dust during mixing. It makes the working spot comfortable and environment friendly. 

Advantage :

• Meets the requirements of IS 15477 (Specification for tile adhesive for ceramic and mosaic tiles) 
• Single component, ready-to-use mixture consisting of cement, sand and special additives 
• Excellent adhesion and slip resistance 
• No water curing, no pre-soaking of tiles
• Long pot life ensuring larger quantities of material being mixed 
• Less labor and time intensive 
• Low water absorption making it water resistant Minimizes shrinkage cracks 
• Trafficable (ready for use) in 24 hours

TIELO Block Fix is a ready to use, self curing and non-shrink block fixing compound, blended carefully and formulated to a prefect adhesive, based on Portland cement, graded aggregates and polymers. By addition of water a high strength thixo-tropic mortar is obtained which is used for laying of Fly Ash bricks, Aerated light weight concrete, cement & hollow blocks and Cellular concrete blocks. Plaster to a thickness of 12mm can also be achieved with TIELO Block Fix to cover up the block work surface and it meets all Standards Nationally as well as Internationally. It conforms to ANSI A118.1 & ANSI A118.4 (1999) , EN-1348 & ASTM C 1660-09.

USES : For preparation of a thin bed adhesive for fixing of AAC, ALC and cellular concrete blocks both for interior and exterior use.

ADVANTAGES

• Easy to use, only water to be added & long working time makes work to be carried at a fast pace and is very economical.
• No curing is required after block fixing work is done.
• Possess the unique property of getting self cured.
• High Strength and perfect adhesion between two blocks.
• Flexible, shock and impact resistant.
• Good mechanical strength. (Bond strength, compressive & tensile strength)
• Thinner joints with high adhesion are achieved contributing to the load bearing capacity of the masonry.

APPLICATION

All surfaces should be sound, clean and free from any contamination like grease, oil, loose particles etc. and structurally sound. Uneven and rough surface should be made smooth before to application of TIELO Block Fix. It can be applied on damp surface also. All slabs must be plumb and true and should be within 1/4 inch (6mm) tin 10ft (3mm). If any Expansion joints are observed it should not be covered with the mortar and treatment to be done as per technical specification mentioned in the drawing.

Mixing : Mix 20 Kg of TIELO Block Fix with 5.5- 6.0 Litre of potable water. The water should be taken in a container and TIELO Block Fix to be added to the water slowly and mixed with hand or a slow speed paddle mixer for 3-4 minutes to obtain a lump free smooth thixo-tropic mix of trowel able consistency. Water can be reduced or increased slightly to achieve desired consistency.

Application as a thin bed mortar for laying blocks : The substrate over which the blocks are to be laid should properly cleaned from all loose particles before placing the mortar. The mortar is placed on the block work in thin layers of 2mm – 3mm with a trowel and the next layer of blocks are placed over it. The joints between the blocks are maintained as per the requirements and to be filled with the mortar by using a trowel. Plumbing is done to maintain the verticality of the wall.

Smoothing over the block work : Application of a bonding layer of 1mm -2mm thick of TIELO Block Fix is to be done using a trowel and pressing it downwards before placing the mixed mortar. Finally using TIELO Block Fix Adhesive of 8mm-10mm thickness it is smoothened with a wooden/rubber float or sponge.

Cleaning : Cleaning of all tools used to be washed with clean water before it gets dried