KARYASIDDHI ENVIRONMENTAL ENGINEERING CO.PVT.LTD. Mumbai, Maharashtra

Cyclonic separation is a method of removing particulates from an air, gas or liquid stream, without the use of filters, through vortex separation. Rotational effects and gravity are used to separate mixtures of solids and fluids. The method can also be used to separate fine droplets of liquid from a gaseous stream.

Dust laden gas or air enters the collector tangentially and follows a spiral path to the bottom of the cone.

The centrifugal force created by the circular flow throws the dust particles toward the wall of the cyclone.

After striking the wall, the combination of the gravitational and swirling forces causes the dust to move downward to the dust outlet. Pressure drop for normal operation is about 3 4 inches of water. They are very efficient in collecting dust particles down to 30 microns in size. Efficiency of the equipment depends on the material being conveyed, material/air flow rates, and cyclone design. Depending upon the application, cyclone separator can be designed in single, twin and quad arrangement and multiclone.

Applications

Steel Industry Blast Furnace, Electric Arc Furnace, BOF, etc

Fertilizer Industry Phosphate Rock Dryers & Calciners, Dryers

Non-Ferrous Copper Reverberatory Furnace, Laea Blast Furnace

Pulp & Paper Lime Kilns, Back Liquor Recovery, Bark Boilers

Sugar Industry Boiler Flue Gas, Bagging Section

Mineral Products Asphalt Stone Dryers, Cement Kilns

Pharmaceuticals Tablet Coating Fans, etc

We are offering Multi Cyclone Dust Collector that consist of a number of small-diameter cyclones, operating in parallel and having a common gas inlet and outlet. Multi-clones operate on the same principle as cyclonescreating a main downward vortex and an ascending inner vortex. Multiclones are more efficient than single cyclones because they are longer and smaller in diameter.The longer length provides longer residence time while the smaller diameter creates greater centrifugal force.

These two factors result in better separation of the dust particles. The pressure drop of the multiclone collectors is higher than that of single cyclone separators.

Applications

Steel Industry Blast Furnace, Electric Arc Furnace, BOF, etc

Fertilizer Industry Phosphate Rock Dryers & Calciners, Dryers

Non-Ferrous Copper Reverberatory Furnace, Laea Blast Furnace

Pulp & Paper Lime Kilns, Back Liquor Recovery, Bark Boilers

Sugar Industry Boiler Flue Gas, Bagging Section

Mineral Products Asphalt Stone Dryers, Cement Kilns

Pharmaceuticals Tablet Coating Fans, etc

The unit is designed to provide a flexible air seal, allowing larger particles to easily pass through the valve while maintaining its air seal. Bolting arrangement on side plate allows service or change-out of the reinforced rubber vane tips without removing the entire unit from the system.Components of a rotary feeder include a rotor shaft, housing, head plates, and packing seals and bearings. Employing Karyasiddhi make rotary airlock

on your dust collection system allows for continuous operation without the need to shut down for barrel removal or lost labor time for barrel change outs. A rotary airlock can also minimize employee exposure to dust while making your system less susceptible to material back-up and damage.

Applications

Steel Industry Blast Furnace, Electric Arc Furnace, BOF, etc

Fertilizer Industry Phosphate Rock Dryers & Calciners, Dryers

Non-Ferrous Copper Reverberatory Furnace, Laea Blast Furnace

Pulp & Paper Lime Kilns, Back Liquor Recovery, Bark Boilers

Sugar Industry Boiler Flue Gas, Bagging Section

Mineral Products Asphalt Stone Dryers, Cement Kilns

Pharmaceuticals Tablet Coating Fans, etc

Double Flap valves find their application as a substitute of Rotary Airlocks i.e. to allow flow of dust and maintain airlock across the valve. It is particularly suitable for handling highly abrasive and gritty materials along with high vacuum across the valve. Two small hoppers are mounted in-line and with some space between them in an air-tight casing. Two sets of flaps/ cones seat against the discharge openings of the hoppers.

The flaps or cones are held on arms that are fulcrummed on two shafts. The shafts are provided with external counter weights to counter balance the weight of flap or cone, the connecting arms and also the material pressure on top. The counter weight is so selected that the flaps / cones close tightly against the seat rings fitted at the discharge end of the hoppers to avoid leakage. The flap/ cone mounting on the connecting arms self aligning type to make the sealing airtight. For cone dump valve, the seats are sometimes provided with additional rubber rings to ensure leakproofness.

The drive mechanism of these valves comprises of a geared motor with cam or linkage that alternately turns the two shafts by some degree. This results in partial lowering of the flap pair or cone at two levels alternately. Thus, as the top flap/cone lowers, material above it drops to fill the intermediate chamber. Now the top flap/cone closes and after some pause the bottom flap/cone opens to allow the material to pass out of the valve. The above mechanism ensures that any one flap/cone remains closed at any point of time thereby ensuring airlock across the valve.

Applications

Steel Industry Blast Furnace, Electric Arc Furnace, BOF, etc

Fertilizer Industry Phosphate Rock Dryers & Calciners, Dryers

Non-Ferrous Copper Reverberatory Furnace, Laea Blast Furnace

Pulp & Paper Lime Kilns, Back Liquor Recovery, Bark Boilers

Sugar Industry Boiler Flue Gas, Bagging Section

Mineral Products Asphalt Stone Dryers, Cement Kilns

Pharmaceuticals Tablet Coating Fans, etc

An agitator is a device or mechanism to put something into motion by shaking or stirring for mixing, blending, suspending, dispersing, heat transfer etc. We offer well-engineered and optimum agitation solutions, mixing agitators, industrial agitators, chemical agitator, industrial agitator, chemical agitators, for all your Mixing Tasks.

Applications

Steel Industry Blast Furnace, Electric Arc Furnace, BOF, etc

Fertilizer Industry Phosphate Rock Dryers & Calciners, Dryers

Non-Ferrous Copper Reverberatory Furnace, Laea Blast Furnace

Pulp & Paper Lime Kilns, Back Liquor Recovery, Bark Boilers

Sugar Industry Boiler Flue Gas, Bagging Section

Mineral Products Asphalt Stone Dryers, Cement Kilns

Pharmaceuticals Tablet Coating Fans, etc

We are specialized in offering high quality Dosing Pump in the market. We have carved a niche as one of the chief High Pressure Dosing Pump Suppliers in India. The Dosing pumps manufactured by us are designed for maximum output and minimum power requirement in the area of their application. Our dosing pumps are backed with various contemporary and advanced features. Its maintenance is extremely simple as well as requires minimum cost.

Quality controllers of our team examine these products to make sure that these are in complete compliance with defined industry standards.

Moreover, these pumps are exceedingly easy to install, assemble and operate. We manufacture complete range of dosing pumps which covers,

Electro- Magnetic Diaphragm Dosing Pumps

Motorised (Mechanical) Diaphragm Dosing Pumps

Motorised Plunger Dosing Pumps

Progressive Cavity (Screw) Pumps

Applications

Steel Industry Blast Furnace, Electric Arc Furnace, BOF, etc

Fertilizer Industry Phosphate Rock Dryers & Calciners, Dryers

Non-Ferrous Copper Reverberatory Furnace, Laea Blast Furnace

Pulp & Paper Lime Kilns, Back Liquor Recovery, Bark Boilers

Sugar Industry Boiler Flue Gas, Bagging Section

Mineral Products Asphalt Stone Dryers, Cement Kilns

Pharmaceuticals Tablet Coating Fans, etc