Our Products

We offer the best product range of CHEMICAL REACTION ENGINEERING Lab and Machine Lab.

Pressure Gauge Tester

The present set-up is designed to calibrate and check the given Bourdon Type pressure gauge. This unit consists of a precision ground plunger, which develops the required pressure by loading of weights. This pressure is transmitted to the pressure gauge by oil

Ask Latest Price & Details

Solid Liquid Extraction Unit

MODEL NO KCMT-104A

The setup consists of Bonnotto type extractor of slotted circular plates arranged one above the other in opposite radial opening. The solids are introduced at the top through a hopper spread over the top plate by a rack and pushed to slot to fall to the next plate below and so on to the bottom of the column. The solvent is introduced near the bottom of the column and it flow upward counter-currently to the solids. A pump supplies the solvent and flow rate is monitored by means of a Rotameter. At the bottom of column a screw conveyor arrangement is done to remove the extracted solids driven by means of an electric motor. Solvent feed tank is kept in a bath fitted with heater and digital temperature controller is used to maintain the constant temperatur

Ask Latest Price & Details

Air Diffusion Equipment

Confirming a packed bed of spherical balls of a solid in a vertical tube, and observing its rate of diffusion into stream of air passed across the top of the tube can conveniently study the diffusion of solid into air. The equipment is fitted with a vertical glass column with a mesh near the base of column to hold the spherical balls. Spherical balls of known weight and diameter are filled in the column to make a packed bed. Air is allowed to pass through the silica gel chamber. From the bottom of the column, dry air is allowed to enter in the packed bed.

Ask Latest Price & Details

Rotary Vacuum Filter

The set-up consists of stainless steel drum moving in gunmetal brackets and is divided in 6 compartments, covered by a Stainless Steel mesh. A canvas filter is used for filtration. The whole assembly is fitted with a SS trough in which a agitator is provided. To make the unit a self-contained a slurry mixing and feed arrangement, receiver tanks, vacuum pump, control panel are provide

Ask Latest Price & Details

Temperature Control Trainer

The setup consists of heating tank fitted with Thyristor-controlled heater for on line heating of the water. Water is supplied from laboratory constant head tank and its flow can be manipulated and measured by provided Rotameter. The temperature of the heated water is sensed by RTD sensor. This measured variable through Temperature Transmitter is communicated to Digital Indicating Controller. Error is calculated and output accordingly, is communicated to Thyristor Controlled heater to achieve the Set Point. These units along with necessary piping are supported in a well-designed housing and are fixed on base plate.

Ask Latest Price & Details

Heat Pipe Demonstrator

In this apparatus the comparison of heat pipe with the copper pipe as good conductor of heat and with the stainless steel pipe as same material of construction is made. It consists of three identical cylindrical conductors in respect of geometry. One end of these is heated electrically while there are small capacity tanks acting as heat sinks at the other end. The unit consists of a heat pipe, a copper pipe and a stainless steel pipe. The performance of the heat pipe as a super-conducting device can be studied well in terms of the temperature distribution along the length at a given instant and can be compared with other two members. Nearly isothermal temperature distribution and fast rise of temperature in heat sink tank reveals the heat pipe superiority over the conventional conductors

Ask Latest Price & Details

Heat Transfer In Forced Convection

The apparatus consists of blower unit fitted with the test pipe. Nichrome wire heater surrounds the test section. Four Temperature Sensors are embedded on the test section, two placed in the air stream at the entrance and exit of the test section to measure the inlet and outlet air temperature. Test pipe is connected to the delivery side of the blower along with the orifice to measure flow of air through the pipe. Constant heat flux is given to pipe by an electric heater through a variac and measured by Digital Voltmeter and Digital Ammeter

Ask Latest Price & Details

Gyratory Sieve Shaker

MODEL NO KCMO-114

Gyratory type shaker is driven by FHP motor through a reduction gear suitable to carry upto 7 sieves of 20 cm diameter. When clamped the sieve table does not rotate but it is inclined from the vertical axis and the direction of inclination changes progressively in the clockwise direction. In addition to the gyratory motion of the shaker, there is an upward and downward movement ensuring that each square inch of the sieve is utilised. The whole mechanism runs in an oil bath. Test Sieves will be supplied at an extra cost. A time switch from 0-60 minutes is provided

Ask Latest Price & Details

Motorized Gyroscope

The set up consists of stainless steel disc mounted on a horizontal shaft, rotated by a variable speed motor. The rotor shaft is coupled to a motor mounted on a trunion frame having bearings in a yoke frame, which is free to rotate about vertical axis. A weight pan on other side of disc balances the weight of motor. Rotor disc can be move about three axis. Torque can be determined by calculating the weight and distance of weight from the center of rotor. The gyroscopic couple can be determine

Ask Latest Price & Details

Ice Plant Trainer

The unit enables the students to study the Basic Principals of ice plant cycle within a short period. The test rig is designed for the study of thermodynamics of vapour Compression refrigeration cycle by way of demonstration and experimentation. It has a facility to measure various parameters for experimentation. Ice cans are kept in liquid tank, which is cooled by the refrigerant evaporator. As conventional ice plants take 12-24 hours to complete the cycle, this ice plant is specially designed to demonstrate process of ice formation to be complete within period of 4 hours and hence it is most suitable for laboratory us

Ask Latest Price & Details

Continuous Stirred Tank Reactor

MODEL NO KCCRE-116A

The set is mounted on the base plate and easily can be installed on the chemical reactor service unit for conducting experiments. Reactants are fed to the system and mixed in the reactor. A variable speed mixer with speed control facility is provided to conduct the experiment on different speed of the impeller thus to determine the effect of mixer speed. Detachable baffles also accompany the reactor vessel. A coil is placed in the reactor through whom hot water with constant temperature is circulated which enables to enhance the experimentations for different temperature

Ask Latest Price & Details

Floatation Cell

MODEL NO KCMO-125

The set up consists of a agitated chamber open at the top. In the chamber, an impeller coupled to a shaft is fixed in a stationary diffuser. Low-pressure air is allowed to enter in the stationary diffuser through the air passage provided with the agitator. The collector coated mineral particles adhere to the rising bubbles and are carried to the top of the cell to be removed in the froth product

Ask Latest Price & Details