Jindal Medi Surge Angled blade plates were designed by the various angled blade plate manufacturer for the fixation of proximal and distal femoral fractures. Later osteotomy plates with different angles were introduced. All angle blade plates are of one-piece construction with a fixed angle between blade and shaft. The fixed angle makes the implant less susceptible to corrosion and increases the strength of the implant. A further benefit of the fixed angle is the possibility of accurate placement of the plate in osteotomies. Angled blade plates with 95 and 130 angles are mainly used for fixations of fracture. Osteotomy plates of different angles are available in sizes for both adolescents, adults, children, and infants. The blade of the plates for adults has a U-cross-section, that provides high strength with minimum bone displacement. Angle blade plates for adolescents, small adults, children, and infants have a T-shaped blade cross-section. Though sharp at the tip, the seat of the blade must be prepared with a seating chisel with the corresponding cross-section. The shaft of the plate is slightly thicker than that of the broad, straight plate and can withstand higher stresses. The dynamic compression holes are arranged in an offset mode, same as the straight broad plates. These holes accept 4.5 mm cortex screws; the round holes in some kinds of plates will accept 6.5 mm cancellous bone screws. for axial compression of fractures of the femur, it is often essential to use the articulated tension device instead of the self-compressing DCP holes. Because of its special design, the insertion of the angled blade plate requires great precision. Preoperative planning is necessary to determine the exact placement of the plate. The blade must be accurately placed in both the frontal and sagittal planes, and the shaft must line up with the axis of the femur. The anatomical landmarks must be known, and guide wires inserted for orientation at the time of surgery. Misplacement of the plate may lead to valgus, varus, or rotational deformities. All plates are available in S.S.316L, LVM & Ti. Alloy.

the goal of any surgical fracture treatment is to reconstruct the anatomy and restore its function. Internal fixation is distinguished by anatomic reduction, preservation of blood supply, stable fixation and early, functional mobilization. Plate and screw osteosynthesis has been established as clinically advantageous for quite some time. Clinical results have improved by using internal fixation with angular stability (internal fixators) in osteopenic bone and in complicated fractures. Jindal medi surge is one of the top-rated large fragment implants and instruments manufacturers in india. The large fragment locking compression plate system is part of a titanium and stainless-steel plate and screw system that merges locking screw technology with conventional plating techniques. The lcp system has many resemblances to conventional plate fixation methods, but with a few important advancements. Locking screws provide the ability to create a fixed angle construct while utilizing familiar plating techniques. A fixed angle construct provides improved fixation in multi fragment fractures or osteopenic bone where traditional screw purchase is compromised. Lcp plate constructs do not depend on plate-to-bone compression to maintain stability, but function similarly to multiple small multi angled blade plates. Locking compression plate allows fracture treatment using conventional plating with conventional cancellous or cortex bone screws, allows fracture treatment using locked plating with uni cortical or bicortical locking screws, permits the combination of locking and conventional screw techniques. The screw design has been modified, from a standard 4.5 mm cortex screw design, to increase fixation and facilitate the surgical procedure. The conical head enables alignment of the locking screw in the threaded plate hole to provide a fixed angle connection between the plate and the screw. The large core diameter improves shear strength and bending of the screw and distributes the load over a larger area in the bone. The shallow head profile of the locking screws results from the larger core diameter and is acceptable because locking screws dont depend only on screw purchase in the bone to maintain stability. Bicortical screw fixation has long been the traditional method of compressing a plate to the bone where a friction between the bone and the plate maintains stability. Load transfer and screw stability are accomplished at two points along the screw: the near and far cortices.

Jindal Medi Surge Mini Fragment Locking System contains the 2.0 mm and 2.4 mm locking implants and related instruments required for locked plating. Features Dedicated equipment designed for LCP plating Locking instruments fit in standard instrument case. The Locking System consists of: Mini Fragment Locking Instrument Set, Mini Fragment Locking Implant Set. All Implants are available in S.S.316L, LVM & Ti. Alloy.

Delta Long P.F.N. Nail

Delta T.F.N. (Trochanetric Femoral Nail)

Delta P.F.N. (Proximal Femoral Nail)

Proximal Bolt Cannulated

End Cap for TFN/PFN Nail

Set Screw for TFN/PFN Nail

Locking Bolt 4.9mm self Tapping

TFN/PFN - Jig - 130

TFN/PFN - Jig - 135

Conical Bolt

Protection Sleeve 12mm/8mm

Protection Sleeve 8mm/6.4mm

Drill Sleeve 4.0mm for Distal Hole

PFN/TFN Guide Wire Sleeve 2.5mm (for 8.0mm Bolt)

PFN/TFN Guide Wire Sleeve 2.0mm (for 6.4mm Bolt)

Cannulated Proximal Reamer 15mm

Protection Sleeve for Cannulated Proximal Reamer

Reamer for 8.0mm PFN/TFN Bolt

Reamer for 6.4mm PFN/TFN Bolt

PFN/TFN Tap 8.0mm

PFN/TFN Tap 6.4mm

Socket Wrench 10mm

Suping Driver

Proximal Cannulated Reamer 15mm

Extractor Rod

Handle for Extractor

Hammer for Extractor Rod

T-Handle Q.C. for 6.4mm & 8.0mm Taps

Tomy Bar

Drill Bit Plain Shank 4.0mm x 250mm Long

Diamond Pointed Awl

Reaming Rod - Plain - 3.0mm Length 850mm

Screw Box Combined for 4.9mm, 6.4mm & 8.0mm Bolt with Screw Trays & Screw Holding Forceps

Trocar with T-Handle 12'' Long for 6.4mm Sleeve

Trocar with T-Handle 12'' Long for 8.0mm Sleeve

Graphic Measuring Scale

Extra Long Screw Driver 3.5mm Tip

Depth Gauge with 150mm Long Sleeve

Reaming Rod with Stopper - 3.0mm Length 850mm

Plastic Medullary Tube

Threaded Guide Wire 2.0mm x 450mm

Threaded Guide Wire 2.5mm, Length 450mm

Direct Measuring Device Length 450mm

Hexagonal Screw Driver Cannulated for 6.4mm & 8.0mm Bolts

Delta Tibial Nail, Lower End Distal Hole (14 Bend)

Delta Tibia Nail 11 Bend (Modified Version)

End Cap for Tibia Nail

Delta Femoral Nail, Lower End Distal Hole

Delta Slim Femur Cannulated Nail

End Cap for Femoral Nail

Locking Bolt 4.9mm Self Tapping

Unreamed (Solid) Delta Tibia Nail Lower End Distal Hole

Proximal Zig for Tibia

Proximal Zig for Femur

Cannulated Conical Bolt for Tibia

Cannulated Conical Bolt for Femur

Extractor Set Containing Two Items (Ram & Rod)

Driving Head

Protection Sleeve 10.0/8.0mm

Drill Sleeve 8.0/4.5mm

Trocar 8.0mm for Delta Tibia Femur Nailing

Tissue Protector

Reamer Rod Plain 2.5mm x 850mm Length

Reaming Rod with Stopper 2.5mm x 850mm Length

Spanner Stainless Steel 17mm

Plastic Medullary Tube

Drill Bit Q.C. S.S. 4.5mm x 4.0mm x 310mm Length

Extra Long Screw Driver 3.5mm Tip

Large Depth Gauge with 150mm Long Sleeve

Diamond Pointed Bone Awl

Protection Sleeve for Proximal Reamer 13mm

Proximal Cannulated Reamer 13.0mm

Screw Box for 4.9 Interlocking Bolts with Screw Tray & Screw Holding Forceps (without Locking Bolts)

Cannulated Awl for Femur I.L. Nails

Proximal Cum Distal Jig for Tibia Fixed Angle

Proximal Cum Distal Jig for Femur Fixed Angle

Proximal & Distal Zig for Tibia Variable Angle

Proximal & Distal Zig for Femur Variable Angle

Proximal Cum Distal Zig Fixed Angle Modified for Tibia

Proximal Cum Distal Zig Fixed Angle Modified for Femur

PFNA Nail-Short - 130 - Length 170mm

PFNA Nail-Short - 130 - Length 240mm

PFNA Nail-Long 130

Locking Bolt 4.9mm Self Tapping

PFNA Helical Blade

End Cap with Set Screw

Radiolucent Jig for PFNA - 130

Conical Bolt for PFNA

Threaded Protection Sleeve for PFNA 11.0mm Reamer & PFNA Blade

Trocar with T-Handle 11.0-mm

Guide Wire Sleeve for 2.5mm x 850mm Long Wire (use with Protection Sleeve 16.5mm)

Protection Sleeve for 4.9mm Locking Bolt

Drill Bit Plain Shank 4.0mm x 300mm Long

Drill Sleeeve for 4.0mm Drill Bit

Depth Gauge for PFNA

Threaded Screw Driver for PFNA Blade

Extra Long Screw Driver 3.5mm Tip for 4.9mm Locking Bolt

Graphic Measuring Scale

Depth Gauge with 150mm Long Sleeve

Guide Wire 2.5mm x 850mm Plain

Threaded Guide Wire 3.0mm x 500mm Long

Plastic Medullary Tube

Proximal Entry Reamer 16.5mm for PFNA

Drill Sleeve for Proximal Reamer 16.5mm

Socket Wrench - 10mm

Cannulated Awl

PFNA Reamer 11.0mm - Length 380mm

Guide Wire Sleeve for PFNA Blade - 3.0mm

T-Handle Quick Coupling

Hammer Guide

Detachable Slide Hammer 400mm gms.

Bone Hammer 200Gms

Impacting Device for Hammer

Jindal Medi Surge Angled blade plates were designed by the various angled blade plate manufacturer for the fixation of proximal and distal femoral fractures. Later osteotomy plates with different angles were introduced. All angle blade plates are of one-piece construction with a fixed angle between blade and shaft. The fixed angle makes the implant less susceptible to corrosion and increases the strength of the implant. A further benefit of the fixed angle is the possibility of accurate placement of the plate in osteotomies. Angled blade plates with 95 and 130 angles are mainly used for fixations of fracture. Osteotomy plates of different angles are available in sizes for both adolescents, adults, children, and infants. The blade of the plates for adults has a U-cross-section, that provides high strength with minimum bone displacement. Angle blade plates for adolescents, small adults, children, and infants have a T-shaped blade cross-section. Though sharp at the tip, the seat of the blade must be prepared with a seating chisel with the corresponding cross-section. The shaft of the plate is slightly thicker than that of the broad, straight plate and can withstand higher stresses. The dynamic compression holes are arranged in an offset mode, same as the straight broad plates. These holes accept 4.5 mm cortex screws; the round holes in some kinds of plates will accept 6.5 mm cancellous bone screws. for axial compression of fractures of the femur, it is often essential to use the articulated tension device instead of the self-compressing DCP holes. Because of its special design, the insertion of the angled blade plate requires great precision. Preoperative planning is necessary to determine the exact placement of the plate. The blade must be accurately placed in both the frontal and sagittal planes, and the shaft must line up with the axis of the femur. The anatomical landmarks must be known, and guide wires inserted for orientation at the time of surgery. Misplacement of the plate may lead to valgus, varus, or rotational deformities. All plates are available in S.S.316L, LVM & Ti. Alloy.

the goal of any surgical fracture treatment is to reconstruct the anatomy and restore its function. Internal fixation is distinguished by anatomic reduction, preservation of blood supply, stable fixation and early, functional mobilization. Plate and screw osteosynthesis has been established as clinically advantageous for quite some time. Clinical results have improved by using internal fixation with angular stability (internal fixators) in osteopenic bone and in complicated fractures. Jindal medi surge is one of the top-rated large fragment implants and instruments manufacturers in india. The large fragment locking compression plate system is part of a titanium and stainless-steel plate and screw system that merges locking screw technology with conventional plating techniques. The lcp system has many resemblances to conventional plate fixation methods, but with a few important advancements. Locking screws provide the ability to create a fixed angle construct while utilizing familiar plating techniques. A fixed angle construct provides improved fixation in multi fragment fractures or osteopenic bone where traditional screw purchase is compromised. Lcp plate constructs do not depend on plate-to-bone compression to maintain stability, but function similarly to multiple small multi angled blade plates. Locking compression plate allows fracture treatment using conventional plating with conventional cancellous or cortex bone screws, allows fracture treatment using locked plating with uni cortical or bicortical locking screws, permits the combination of locking and conventional screw techniques. The screw design has been modified, from a standard 4.5 mm cortex screw design, to increase fixation and facilitate the surgical procedure. The conical head enables alignment of the locking screw in the threaded plate hole to provide a fixed angle connection between the plate and the screw. The large core diameter improves shear strength and bending of the screw and distributes the load over a larger area in the bone. The shallow head profile of the locking screws results from the larger core diameter and is acceptable because locking screws dont depend only on screw purchase in the bone to maintain stability. Bicortical screw fixation has long been the traditional method of compressing a plate to the bone where a friction between the bone and the plate maintains stability. Load transfer and screw stability are accomplished at two points along the screw: the near and far cortices.

Jindal Medi Surge Mini Fragment Locking System contains the 2.0 mm and 2.4 mm locking implants and related instruments required for locked plating. Features Dedicated equipment designed for LCP plating Locking instruments fit in standard instrument case. The Locking System consists of: Mini Fragment Locking Instrument Set, Mini Fragment Locking Implant Set. All Implants are available in S.S.316L, LVM & Ti. Alloy.

Delta Long P.F.N. Nail

Delta T.F.N. (Trochanetric Femoral Nail)

Delta P.F.N. (Proximal Femoral Nail)

Proximal Bolt Cannulated

End Cap for TFN/PFN Nail

Set Screw for TFN/PFN Nail

Locking Bolt 4.9mm self Tapping

TFN/PFN - Jig - 130

TFN/PFN - Jig - 135

Conical Bolt

Protection Sleeve 12mm/8mm

Protection Sleeve 8mm/6.4mm

Drill Sleeve 4.0mm for Distal Hole

PFN/TFN Guide Wire Sleeve 2.5mm (for 8.0mm Bolt)

PFN/TFN Guide Wire Sleeve 2.0mm (for 6.4mm Bolt)

Cannulated Proximal Reamer 15mm

Protection Sleeve for Cannulated Proximal Reamer

Reamer for 8.0mm PFN/TFN Bolt

Reamer for 6.4mm PFN/TFN Bolt

PFN/TFN Tap 8.0mm

PFN/TFN Tap 6.4mm

Socket Wrench 10mm

Suping Driver

Proximal Cannulated Reamer 15mm

Extractor Rod

Handle for Extractor

Hammer for Extractor Rod

T-Handle Q.C. for 6.4mm & 8.0mm Taps

Tomy Bar

Drill Bit Plain Shank 4.0mm x 250mm Long

Diamond Pointed Awl

Reaming Rod - Plain - 3.0mm Length 850mm

Screw Box Combined for 4.9mm, 6.4mm & 8.0mm Bolt with Screw Trays & Screw Holding Forceps

Trocar with T-Handle 12'' Long for 6.4mm Sleeve

Trocar with T-Handle 12'' Long for 8.0mm Sleeve

Graphic Measuring Scale

Extra Long Screw Driver 3.5mm Tip

Depth Gauge with 150mm Long Sleeve

Reaming Rod with Stopper - 3.0mm Length 850mm

Plastic Medullary Tube

Threaded Guide Wire 2.0mm x 450mm

Threaded Guide Wire 2.5mm, Length 450mm

Direct Measuring Device Length 450mm

Hexagonal Screw Driver Cannulated for 6.4mm & 8.0mm Bolts

Delta Tibial Nail, Lower End Distal Hole (14 Bend)

Delta Tibia Nail 11 Bend (Modified Version)

End Cap for Tibia Nail

Delta Femoral Nail, Lower End Distal Hole

Delta Slim Femur Cannulated Nail

End Cap for Femoral Nail

Locking Bolt 4.9mm Self Tapping

Unreamed (Solid) Delta Tibia Nail Lower End Distal Hole

Proximal Zig for Tibia

Proximal Zig for Femur

Cannulated Conical Bolt for Tibia

Cannulated Conical Bolt for Femur

Extractor Set Containing Two Items (Ram & Rod)

Driving Head

Protection Sleeve 10.0/8.0mm

Drill Sleeve 8.0/4.5mm

Trocar 8.0mm for Delta Tibia Femur Nailing

Tissue Protector

Reamer Rod Plain 2.5mm x 850mm Length

Reaming Rod with Stopper 2.5mm x 850mm Length

Spanner Stainless Steel 17mm

Plastic Medullary Tube

Drill Bit Q.C. S.S. 4.5mm x 4.0mm x 310mm Length

Extra Long Screw Driver 3.5mm Tip

Large Depth Gauge with 150mm Long Sleeve

Diamond Pointed Bone Awl

Protection Sleeve for Proximal Reamer 13mm

Proximal Cannulated Reamer 13.0mm

Screw Box for 4.9 Interlocking Bolts with Screw Tray & Screw Holding Forceps (without Locking Bolts)

Cannulated Awl for Femur I.L. Nails

Proximal Cum Distal Jig for Tibia Fixed Angle

Proximal Cum Distal Jig for Femur Fixed Angle

Proximal & Distal Zig for Tibia Variable Angle

Proximal & Distal Zig for Femur Variable Angle

Proximal Cum Distal Zig Fixed Angle Modified for Tibia

Proximal Cum Distal Zig Fixed Angle Modified for Femur

PFNA Nail-Short - 130 - Length 170mm

PFNA Nail-Short - 130 - Length 240mm

PFNA Nail-Long 130

Locking Bolt 4.9mm Self Tapping

PFNA Helical Blade

End Cap with Set Screw

Radiolucent Jig for PFNA - 130

Conical Bolt for PFNA

Threaded Protection Sleeve for PFNA 11.0mm Reamer & PFNA Blade

Trocar with T-Handle 11.0-mm

Guide Wire Sleeve for 2.5mm x 850mm Long Wire (use with Protection Sleeve 16.5mm)

Protection Sleeve for 4.9mm Locking Bolt

Drill Bit Plain Shank 4.0mm x 300mm Long

Drill Sleeeve for 4.0mm Drill Bit

Depth Gauge for PFNA

Threaded Screw Driver for PFNA Blade

Extra Long Screw Driver 3.5mm Tip for 4.9mm Locking Bolt

Graphic Measuring Scale

Depth Gauge with 150mm Long Sleeve

Guide Wire 2.5mm x 850mm Plain

Threaded Guide Wire 3.0mm x 500mm Long

Plastic Medullary Tube

Proximal Entry Reamer 16.5mm for PFNA

Drill Sleeve for Proximal Reamer 16.5mm

Socket Wrench - 10mm

Cannulated Awl

PFNA Reamer 11.0mm - Length 380mm

Guide Wire Sleeve for PFNA Blade - 3.0mm

T-Handle Quick Coupling

Hammer Guide

Detachable Slide Hammer 400mm gms.

Bone Hammer 200Gms

Impacting Device for Hammer