Our Products
Bandages
1 Products availableMetal & Metal Products
1 Products availablePackaging Foils & Films
1 Products availablePlumbing & Pipe Fittings
1 Products availableOur Complete range of products are Aluminium 5086 Sheet, Aluminium 5052 Plate, Aluminium 1070 Hex Bars, Aluminium 1060 Pipes and Aluminium 1070 Pipes.
Aluminium 5086 Sheets Chemical Composition
Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Others, each | Others, total | Al |
0.4 | 0.5 | 0.1 | 0.20-0.70 | 3.5-4.5 | 0.05-0.25 | 0.25 | 0.15 | 0.05 | 0.15 | Balance |
Mechanical Properties of Aluminum 5086 Sheets
Proof Stress | Tensile Strength | Hardness Brinell | Elongation |
125 Min MPa | 275 - 350 MPa | 75 HB | 12 Min % |
Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Al |
0.50 | 0.50 | 3.8/4.9 | 0.30/0.9 | 1.2/1.8 | 0.10 | 0.25 | 0.15 | Balance |
Hardness, Brinell | Poisson's Ratio | Melting Point | Electrical Resistivity | Modulus of Elasticity | Specific Heat |
47 | 0.33 | 607 - 649 °C | 4.99e-006 ohm-cm | 70.3 GPa | 0.88 J/g-°C |
Properties | Conditions | ||
T (°C) | Treatment | ||
Density (×1000 kg/m3) | 7.7-8.03 | 25 | |
Poisson's Ratio | 0.27-0.30 | 25 | |
Elastic Modulus (GPa) | 190-210 | 25 | |
Tensile Strength (Mpa) | 640 | 25 | cold drawn, spheroidized annealed more |
Yield Strength (Mpa) | 495 | ||
Elongation (%) | 10 | ||
Reduction in Area (%) | 45 | ||
Hardness (HB) | 192 | 25 | cold drawn, spheroidized annealed more |
Properties | Conditions | ||
T (°C) | Treatment | ||
Thermal Expansion (10-6/ºC) | 11.8 | 0-100 more | rolled |
Aluminium 1060 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
0.15 - 0.20 | 0.10 - 0.15 | 0.01 - 0.03 | 0.01 - 0.03 | 0.01 - 0.05 | 0.01 - 0.03 | 0.020 - 0.030 | 99.60 |
Mechanical Properties - Al 1060 | |||||||||||||||||||
Alloy | Temper | UTS(Mpa) | % Elongation | ||||||||||||||||
Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | |||||||||||||||
1060 | O | 55 | 75 | 25 | 25 | 30 | |||||||||||||
H12 | 75 | 110 | 6 | 6 | 7 | ||||||||||||||
H14 | 90 | 120 | 5 | 5 | 6 | ||||||||||||||
H16 | 95 | 130 | 4 | 4 | 4 | ||||||||||||||
H18 | 130 | --- | 3 | 3 | 3 | 23 |
Aluminium 1070 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
0.25 | 0.2 | 0.03 | 0.03 | 0.03 | 0.07 | 0.03 | 99.70 |
Properties | Conditions | ||
T (°C) | Treatment | ||
Density (×1000 kg/m3) | 7.7-8.03 | 25 | |
Poisson's Ratio | 0.27-0.30 | 25 | |
Elastic Modulus (GPa) | 190-210 | 25 | |
Tensile Strength (Mpa) | 640 | 25 | cold drawn, spheroidized annealed more |
Yield Strength (Mpa) | 495 | ||
Elongation (%) | 10 | ||
Reduction in Area (%) | 45 | ||
Hardness (HB) | 192 | 25 | cold drawn, spheroidized annealed more |
Alloy | Fe | Si | Mg | Mn | Cu | Zn | Ti | Cr | Others | AI |
1100 (min) | 0.35 | 0.25 | 0.01 | 0.01 | 0.05 | 0.01 | 0.020 | Trace | 0.05 (each) | 99.60% |
1100 (max) | 0.50 | 0.35 | 0.03 | 0.05 | 0.20 | 0.05 | 0.030 | Trace | 0.15 (total) | remainder |
Alloy | Temper | UTS(Mpa) | % Elongation | |||
Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | ||
1100 | O | 75 | 110 | 20 | 25 | 29 |
H12 | 95 | 130 | 5 | 6 | 7 | |
H14 | 110 | 145 | 3 | 4 | 5 | |
H16 | 130 | 165 | 2 | 3 | 4 | |
H18 | 150 | --- | 2 | 2 | 3 |
Aluminium 2014 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
0.7 | 0.50 - 1.20 | 0.2 - 0.8 | 0.4 - 1.2 | 3.9 - 5.0 | 0.25 | 0.15 | 93.5 |
Material | Temper | Diameter (mm) | Tensile Strength min ((N/mm²) | Yield Strength (min) (N/mm²) | Elongation on 5.65 V (min) |
2014 Pipes | T4 | <20 | 370 | 230 | 11 |
2014 Pipes | T4 | 20-75 | 390 | 250 | 11 |
2014 Pipes | T4 | 75-150 | 390 | 250 | 9 |
2014 Pipes | T4 | 150-200 | 370 | 230 | 8 |
2014 Pipes | T6510 | 20-75 | 480 | 435 | 7 |
2014 Pipes | T6510 | 75-150 | 465 | 420 | 7 |
Al | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Other Each | Other Total |
Bal. | 0.20-0.8 | 0.7 max | 3.5-4.5 | 0.40-1.0 | 0.40-0.8 | 0.10 max | 0.25 max | 0.15 max | 0.05 max | 0.15 max |
Material | Condition | Tensile Strength (N/mm²) min | Yield Strength | Elongation in 4D % | ||
ksi | Mpa | ksi | Mpa | |||
Al 2017 | 2017-T4 Bar | 55 | 379 | 32 | 221 | 12 |
Grade | Al | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Other |
min. | Bal | 3.80 | 0.30 | 1.20 | ||||||
max. | Bal | 0.50 | 0.50 | 4.90 | 0.90 | 1.80 | 0.10 | 0.25 | 0.15 | 0.05 |
Temper | Tensile Strength | Yield Strength | Elongation |
KSI | KSI | % | |
(annealed) | 32 | 14 | 12 |
T3 | 63 | 42 | 15 |
Al | Cr | Cu | Fe | Mg | Mn | Other Total | Si | Ti | Zn |
Remainder | - | 0.05 to 0.20% | 0.7% | - | 1.0 to 1.5% | 0.15% | 0.6% | - | 0.10% |
Properties | Metric | Imperial |
Tensile strength | 130 MPa | 18855 psi |
Yield strength | 125 MPa | 18130 psi |
Shear strength | 83 MPa | 12039 psi |
Fatigue strength | 55 MPa | 7977 psi |
Elastic modulus | 70-80 GPa | 10153-11603 ksi |
Poisson's ratio | 0.33 | 0.33 |
Elongation | 10% | 10% |
Hardness | 35 | 35 |
GRADE | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Al |
5052 | 0.50 | 0.50 | 3.8/4.9 | 0.30/0.9 | 1.2/1.8 | 0.10 | 0.25 | 0.15 | Balance |
Mechanical Property | Hardness, Brinell | Poisson's Ratio | Melting Point | Electrical Resistivity | Modulus of Elasticity | Specific Heat |
Value | 47 | 0.33 | 607 - 649 °C | 4.99e-006 ohm-cm | 70.3 GPa | 0.88 J/g-°C |
Mg | Mn | Si | Cu | Fe | Cr | Zn | Ti | Cu | Other (Each) | Others (Total) | Al |
2.60 - 3.60 | 0.0 - 0.50 | 0.0 - 0.40 | 0.0 - 0.40 | 0.0 - 0.30 | 0.0 - 0.20 | 0.0 - 0.15 | 0.0 - 0.10 | 0.0 - 0.05 | 0.0 - 0.05 | 0.0 - 0.15 | Balance |
Proof Stress | Tensile Strength | Elongation at 50 mm | Hardness Brinell |
80 Min MPa | 190 - 260MPa | 12 Min % | 52 HB |
Weight% | Al | Si | Fe | Cu | Mn | Cr | Mg | Ti | Zn | Other Each | Others Total |
5083 | Bal | 0.40 max | 0.40 max | 0.10 max | 0.40 / 1.0 | 0.05 / 0.25 | 4.0 / 4.90 | 0.15 max | 0.25 max | 0.05 max | 0.15 max |
Properties | Proof Stress | Tensile Strength | Hardness Brinell | Elongation |
Metric | 125 Min MPa | 275 - 350 MPa | 75 HB | 12 Min % |
Cu | Si | Fe | Mn | Mg | Zn | Cr | Ti | Other Each | Others Total | Al |
.10 (max) | .20/.60 | .35 (max) | .10 (max) | .45/.90 | .10 (max) | .10 (max) | .10 (max) | .05 | .015 | Remainder |
Tensile Strength (psi) | Yield Strength (psi) | Elongation (% in 2") | Brinell Hardness |
27,000 | 21,000 | 12 | 60 |
Weight% | Al | Si | Fe | Cu | Mn | Cr | Mg | Zn | Ti | Other Each | Others Total |
Aluminium 6082 | Bal | 0.7 - 1.3 | 0.50 max | 0.10 max | 0.40-1.00 | 0.25 max | 0.06-1.20 | 0.20 max | 0.10 max | 0.05 max | 0.15 max |
Diameter or minor sectional dimension mm | Tensile Strength, MPa | Yield Strength 0.2%, MPa | Elongation % |
0-20 | 295 | 255 | 8 |
20-150 | 310 | 270 | 8 |
150-200 | 280 | 240 | 5 |
Material | Temper | Tensile Strength (ksi) | Yield Strength (ksi) | Elongation in 2" % |
Aluminium Alloy 8011 Angle (AMS 4340) | T76511 | 79 | 69 | 7 |
Aluminium Alloy 8011 Angle (AMS 4340) | T73511 | 70 | 60 | 8 |
Aluminium Alloy 8011 Angle (AMS 4342) | T74511 | 73 | 63 | 7 |
Aluminium 1060 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
0.15 - 0.20 | 0.10 - 0.15 | 0.01 - 0.03 | 0.01 - 0.03 | 0.01 - 0.05 | 0.01 - 0.03 | 0.020 - 0.030 | 99.60 |
Mechanical Properties - Al 1060 | |||||||||||||||||||
Alloy | Temper | UTS(Mpa) | % Elongation | ||||||||||||||||
Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | |||||||||||||||
1060 | O | 55 | 75 | 25 | 25 | 30 | |||||||||||||
H12 | 75 | 110 | 6 | 6 | 7 | ||||||||||||||
H14 | 90 | 120 | 5 | 5 | 6 | ||||||||||||||
H16 | 95 | 130 | 4 | 4 | 4 | ||||||||||||||
H18 | 130 | --- | 3 | 3 | 3 |
Aluminium 1070 | Fe | Si | Mg | Mn | Cu | Zn | Ti | Al |
0.25 | 0.2 | 0.03 | 0.03 | 0.03 | 0.07 | 0.03 | 99.70 |
Mechanical Properties - Al 1070 | |||||||||||||||||||
Properties | Conditions | ||||||||||||||||||
T (°C) | Treatment | ||||||||||||||||||
Density (×1000 kg/m3) | 7.7-8.03 | 25 | |||||||||||||||||
Poisson's Ratio | 0.27-0.30 | 25 | |||||||||||||||||
Elastic Modulus (GPa) | 190-210 | 25 | |||||||||||||||||
Tensile Strength (Mpa) | 640 | 25 | cold drawn, spheroidized annealed more | ||||||||||||||||
Yield Strength (Mpa) | 495 | ||||||||||||||||||
Elongation (%) | 10 | ||||||||||||||||||
Reduction in Area (%) | 45 | ||||||||||||||||||
Hardness (HB) | 192 | 25 | cold drawn, spheroidized annealed more |
Alloy | Fe | Si | Mg | Mn | Cu | Zn | Ti | Cr | Others | AI |
1100 (min) | 0.35 | 0.25 | 0.01 | 0.01 | 0.05 | 0.01 | 0.020 | Trace | 0.05 (each) | 99.60% |
1100 (max) | 0.50 | 0.35 | 0.03 | 0.05 | 0.20 | 0.05 | 0.030 | Trace | 0.15 (total) | remainder |
Alloy | Temper | UTS(Mpa) | % Elongation | |||
Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | ||
1100 | O | 75 | 110 | 20 | 25 | 29 |
H12 | 95 | 130 | 5 | 6 | 7 | |
H14 | 110 | 145 | 3 | 4 | 5 | |
H16 | 130 | 165 | 2 | 3 | 4 | |
H18 | 150 | --- | 2 | 2 | 3 |
Grade | Al | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Other |
min. | Bal | 3.80 | 0.30 | 1.20 | ||||||
max. | Bal | 0.50 | 0.50 | 4.90 | 0.90 | 1.80 | 0.10 | 0.25 | 0.15 | 0.05 |
Temper | Tensile Strength | Yield Strength | Elongation |
KSI | KSI | % | |
(annealed) | 32 | 14 | 12 |
T3 | 63 | 42 | 15 |
Al | Cr | Cu | Fe | Mg | Mn | Other Total | Si | Ti | Zn |
Remainder | - | 0.05 to 0.20% | 0.7% | - | 1.0 to 1.5% | 0.15% | 0.6% | - | 0.10% |
Properties | Metric | Imperial |
Tensile strength | 130 MPa | 18855 psi |
Yield strength | 125 MPa | 18130 psi |
Shear strength | 83 MPa | 12039 psi |
Fatigue strength | 55 MPa | 7977 psi |
Elastic modulus | 70-80 GPa | 10153-11603 ksi |
Poisson's ratio | 0.33 | 0.33 |
Elongation | 10% | 10% |
Hardness | 35 | 35 |
Cu | Si | Fe | Mn | Mg | Zn | Cr | Ti | Other Each | Others Total | Al |
.10 (max) | .20/.60 | .35 (max) | .10 (max) | .45/.90 | .10 (max) | .10 (max) | .10 (max) | .05 | .015 | Remainder |
Tensile Strength (psi) | Yield Strength (psi) | Elongation (% in 2") | Brinell Hardness |
27,000 | 21,000 | 12 | 60 |
Weight % | Zn | Cu | Mg | Zr | Fe | Si | Mn | Ti | Cr | Others (total) |
Minimum | 5.7 | 2.0 | 1.9 | 0.08 | - | - | - | - | - | - |
Maximum | 6.7 | 2.6 | 2.6 | 0.15 | 0.15 | 0.12 | 0.10 | 0.06 | 0.04 | 0.15 |
Material | Temper | Tensile Strength (ksi) | Yield Strength (ksi) | Elongation in 2" % |
Aluminium Alloy 7050 Angle (AMS 4340) | T76511 | 79 | 69 | 7 |
Aluminium Alloy 7050 Angle (AMS 4340) | T73511 | 70 | 60 | 8 |
Aluminium Alloy 7050 Angle (AMS 4342) | T74511 | 73 | 63 | 7 |
Alloy | Temper | UTS(Mpa) | % Elongation | |||
Min | Max | 0.5 mm -0.8 mm | 0.81 mm - 1.30 mm | 1.30 mm - above | ||
1060 | O | 55 | 75 | 25 | 25 | 30 |
H12 | 75 | 110 | 6 | 6 | 7 | |
H14 | 90 | 120 | 5 | 5 | 6 | |
H16 | 95 | 130 | 4 | 4 | 4 | |
H18 | 130 | --- | 3 | 3 | 3 |
Properties | Conditions | ||
T (°C) | Treatment | ||
Density (×1000 kg/m3) | 7.7-8.03 | 25 | |
Poisson's Ratio | 0.27-0.30 | 25 | |
Elastic Modulus (GPa) | 190-210 | 25 | |
Tensile Strength (Mpa) | 640 | 25 | cold drawn, spheroidized annealed more |
Yield Strength (Mpa) | 495 | ||
Elongation (%) | 10 | ||
Reduction in Area (%) | 45 | ||
Hardness (HB) | 192 | 25 | cold drawn, spheroidized annealed more |
Aluminium 2014 Sheets Chemical Composition
Alloy | Si | Fe | Cu | Zn | Mn | Mg | Ti | Other | Cr | Ni | Others | Ti+Zr | Al |
2014 (min) (max) | 0.50 - 0.90 | 0.0 - 0.50 | 3.90 - 5.00 | 0.0 - 0.25 | 0.40 - 1.20 | 0.20 - 0.80 | 0.0 - 0.15 | 0.0 - 0.15 | 0.0 - 0.10 | 0.0 - 0.10 | 0.0 - 0.05 | 0.0 - 0.20 | Balance |
Mechanical Properties of Aluminum 2014 Sheets
Alloy | Temper | UTS (Mpa) | Yield Strength (Mpa) | Elongation (%) | ||
- | - | Minimum | Maximum | Minimum | Maximum | A 50mm (Minimum) |
EN AW-2014 | O | – | 250 | – | 135 | 10 |
T4 | 370 | – | 230 | – | 11 |
Aluminium 2024 Sheets Chemical Composition
Grade | Al | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Other |
min. | Bal | 3.80 | 0.30 | 1.20 | ||||||
max. | Bal | 0.50 | 0.50 | 4.90 | 0.90 | 1.80 | 0.10 | 0.25 | 0.15 | 0.05 |
Mechanical Properties of Aluminum 2024 Sheets
Temper | Tensile Strength | Yield Strength | Elongation |
KSI | KSI | % | |
(annealed) | 32 | 14 | 12 |
T3 | 63 | 42 | 15 |