Innovative Flexotech Pvt. Ltd.

Thaltej, Ahmedabad, Gujarat

• @FlexoPhotopolymer Plate Making Machine
• ForWaterwash flexo Plate Making Equipment
• (Model : @C-A2SSF / @C-A3SSF / @C-A4SSF / @C-2430 / @C-3040)
• Plates suitable : Label, film, paper, corrugated board, paper carton, bag, Tetra pak etc. Exposure + Washout + Drying +Treatment (Light finishing) in complete set @C-A2SSF
• All stainless steel.
• Exposing+drying+washout+treatment.
• With water circulation & filtration system.
• Simple operation, best plate result

photopolymer plate-making machine. The machine can process plates ranging from 21*30cms to 40*50 inch in different models. The company will also run live demo of its Techsetter2 thermal imagesetter. A complete in-house production in india, 24*7 online service support, and a claim that it offers 15 of its equipments that are set along with CTP 200 LPI1% reproduction systems.

This Machine is suitable to printing of rolling paper. Packing paper glass paper, P.P., P.E. and Polysterene HDPE etc.The built-in impression counter can be presented and stops the machine automatically when the desired quality of prints is acquired, and starts again on reset.Using a hot-air dryer and a cold-air fan simultaneously, it makes the production speedier. The dryer and fan will shut down automatically when the machine stops, it makes this machine more safe.

Instant light up Philips high intensity lamps, Excellent lamps cooling exhausting system, Quick vacuum drawdown pump with indicator, Temperature adjustable by a precise controller.

This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling, can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.

Using hydraulic system to set the printing plates, it is easy and accurate. There will be no defects when starting and stopping the machine.The throw-off or on action of printing cylinder is hydraulically operated. The interlocking mechanism keeps the inking rolls running to avoid drying of ink on such rolls, accomplishing the throw-off of printing cylinder.

This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.

B. Technical information:

Recovery volume: 100 litersPower consume: 220V AC 6.65KWDiathermic oil: 40 KGMachine dimension: Main body: 1500x 9801500 mmRecovery rate: 85%Recovery time: 3 4 hours

C. Operating steps:

1. After opening the crate, plug in 220 V power, and connect the ground (earth).2. Open the lid and fill the tank up to the level with solvent to be recovered (100 L)3. Close the lid and tighten it.4. Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe (1).5. set up the thermostat (18) for example for Perc. Is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure (3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat (11) at 40 degree C.6. Turn on the power switch (15), steam cooling switch (16), heater switch (17) and vacuum pump switch (12).7. If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer (14) then turn on the switch (13).

D. Important:

1. Install the unit in a wide and ventilated place.2. Disconnect electric power before doing any action.3. No taking off the control panel4. Change the diathermic oil every 1000 working hours.5. No filling the solvent container up over the level (100 liters)6. Remove the waste after every recovery process

MODELS : @A4-FL @A3-FLPlate Making : For Photopolymer StampExposure + Washout + Drying + Treatment Units 4 in 1