Industrial Marketing Company

Andheri, Mumbai, Maharashtra

• Fully Automatic Readout of :
• # Optical Rotation
• # Specific Rotation
• # Concentration
• # International Sugar Scale
• Large Multi functional LCD Display
• Easy Interactive Setup Menu
• RS-232 / USB Output Port
• Automatic Calculation of Average Value and Repeatability Factor
• Tungsten Lamp light source with filter
• Angular Scale : -45 to +45, LC : 0.001
• Sugar Scale +130 to -130 ISS
• Minimum Transmission : 1%

The antibiotic zone provides a rapid accurate method for determining the strength of antibiotic materials by measuring the diameter of an inhibited zone in Petri- dish

In use, the discs are placed on Petri-dish prepared with agar and inoculated with bacteria. After incubation, the bacterial cover the entire dish except for a circular in habited zone around being a function of the strength of the antibiotic.

This zone reader measures the diameter of the inhibited zone to 0.02 mm within range of 0 to 35 mm diameter. Light from a source in the base, passes through the transparent and semitransparent portion of the agar, then to a reflecting mirror supported by an arm above the unit. The mirror reflects the light to glass prism mounted at the front of the unit and magnified image of the zone of inhibition is clearly visible on the prism.

• Digital Indications of antibiotic zone diameter using a micro-computer.
• Measurement range 00.00 to 35.00 mm diameter readability 0.01 mm.
• Average of two diameter readings in vertical and horizontal direction of inhibited zone.
• Recall average diameter of inhibited zone.
• Key operations are acknowledged by beep sound.
• S.S. calibrated coins for calibration
• IQ / OQ Documentation

• Advantages :

  • An accurate method of determining the strength of antibiotic materials.
  • Magnified image of the inhibited zone is clearly visible on the prism.
  • Less time consuming for measuring the accurate diameter of an inhibited zone. (+/- 0.1 mm)
  • Easy to operate for single person.
  • Display shows direct reading.
  • Vertical & horizontal reading of the zone stored in memory.

Humidity Control Ovens are developed as a result of intensive innovation. The ovens confirm to international standards and are manufactured as per GMP regulations.

ICH Guidelines :

Stability Chambers are designed specifically to meet ICH guidelines for general stability testing of new drug substances and products as per Q1A (R), for long term intermediate and accelerated testing.

IQ, OQ, PQ & DQ :

Provides protocols for Installation Qualification (IQ), Operation Qualification (OQ), Performance Qualification (PQ) and Design Qualification (DQ) with MOC and SOP.

Calibration and Validation :

Calibrates the chamber and provides certificate with traceability. Also assures the uniformity in the chamber and complies to as per guidelines.

Construction :

The unit is a double walled, with exteriors made of mild steel, finished with powder coated epoxy paint. (optional-exterior made of stainless steel). Interiors made of stainless steel. The unit has glass wool insulation with full length inner glass door with latch. The outer door is a double walled metal door with magnetic gasket and lock. The unit has perforated adjustable and removable stainless steel trays, with forced air circulation for uniform temperature. The unit rests on castor wheels for easy movability.

Heating and Cooling :

The unit has been incorporated with long lasting S.S. tubular heaters with fins for better heat transfer. A hermetically sealed compressor coupled with evaporation coil and fan cooled condenser provides efficient cooling in the chamber. The cooling system is placed at the bottom of the machine for easy servicing. The compressor is safeguarded with time delay circuit.

Humidity :

Humidity is formed by steam injection in the chamber. Humidity formed is non-condensing type to avoid droplets deposition on the samples. For steam formation a boiler tank is provided and connected with water tank (Reservoir). A float valve is provided in the water tank to control the water level.

Sensors :

The temperature of the chamber is sensed by PT-100 sensor measured in I0;C, with 0.1I0; C resolution. The set and measured temperature is displayed separately.

The humidity in the chamber is sensed by electronic capacitance type senor and measured directly in %RH with 0.1I0;% RH. The set and measured humidity is displayed separately.

Control Panel :

The unit will be supplied with front panel at the top consisting of digital display microprocessor based temperature / humidity controller along with PT-100 temperature sensor and RH sensor for humidity control, ampere meter, main ON/OFF switch (MCB) and pilot lamps for all controls.

Salient Features :

• Humidity is directly displayed in terms of % RH measured directly by RH sensor.
• Acoustic alarm is provided for detecting the temperature / humidity deviation from set value.
• Alarms are also provided for boiler water low level and open sensor.
• Dual Safety systems has been provided for over temperature in case of malfunction to protect the samples.
• Better reliability for its performance

Supply Voltage : 230 Volts, AC 50 Hz

Microprocessor Based Temperature and Humidity Controllers :

Control Panel :

The control panel is a membrane key board provided with digital display selectable indicators. The data mode has the following parameters : 1) Real Time, 2) Date, Month and Year, 3) Temperature / Humidity, 4) Print interval duration 10 to 990 mins. 5) Print Mode (on / off line)

A) Ordering Information

TEMP RANE:10 C TO 50ACCURACY:+/- 0.5C.

HUMIDITY RANGE:40 TO 95% RH ACCURACY:+/-3% RH

Centronic Port For Printing Data on Printer :

The unit offer data printing on printer at the desired duration the recording interval can vary from 10 to 990 minutes in step of 10 minutes and can store data upto 3000 readings (If print interval is 30 mins. Then it stores upto 30 days). This enables one to maintain a records of the test as per the requirements of GMP & FDA regulations.

RS 485 Port For Interfacing With Computer

OPTIONALS :-

Temperature / Humidity Scanner 4 Points (auto Validation System) :

The unit can be supplied with a 4- point temperature and 4-point humidity scanner, with PT-100 temperature sensor and electronic humidity sensor. The sensors are placed at the four corners of the chamber i.e. at the upper and lower part of the chamber to know about the temperature / humidity gradient (i.e. self validation system). The data can be stored in memory. The recording interval can vary from 10 to 990 minutes in step of 10 minutes and can be printed on a dot matrix printer. The data can also be stored in a computer.

Dot Matrix Printer :

The unit can be supplied with 80 columns dot matrix printer with trolley for printing data i.e. date-time, set-temperature, measured-temp, set RH and measured RH.